Pentair · IntelliFlo VSF
Pentair IntelliFlo VSF
The IntelliFlo before the IntelliFlo3: the parts that changed in late 2020, the WhisperFlo wet end it shares, and the settings that look like faults.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The IntelliFlo VSF was Pentair's variable speed and flow pump before the IntelliFlo3. Like the IntelliFlo3, it can hold a speed or a flow. The IntelliFlo VS shares its wet end and, from 2019, its motor, but has its own drive and no flow control. Set a flow anywhere from 20 to 140 GPM and the pump changes its own speed to keep it as the filter loads.
Pentair's product page now marks it discontinued, under item number 011056. Its parts aren't. Pentair's 2025–2026 catalog, updated September 2025, still lists the wet end, the motor and both versions of the drive, with prices. This page is for the pump already on your pad.
Find out which build you have
Pentair changed three parts partway through production: the impeller, the diffuser and the drive, and with it the drive assembly. The 2020 manual splits them at November 2020. The 2025–2026 catalog says October 2020 for the impeller, diffuser and drive, and November 2020 for the drive assembly.
The two builds share one item number, 011056. Pentair doesn't say whether the later parts fit an earlier pump. Ask a Pentair dealer to confirm which build you have before ordering any of the three. Both are in the table below.
One printing error is worth knowing about. The manual labels both drive rows "before 11/20". The catalog puts 356944z after the change, and its drive history table names 356944z as the current drive for 011056.
The wet end is a WhisperFlo's
Most of this pump's wet end carries the WhisperFlo's part numbers: the lid clamp, lid, lid o-ring, basket, volute, drain plugs, shaft seal and seal plate kit. On a pump built before late 2020, so do the impeller and diffuser. They're the parts of the 3 HP WhisperFlo, the WFE-12.
So Pentair sells kits for this wet end that it also lists for the WhisperFlo pumps:
- Quick kit, 356198. Every seal and o-ring you'd replace with the pump apart, at $53.55 US list. The shaft seal alone lists at $48.53.
- Seal plate kit, 350202. The seal plate with the shaft seal already pressed in, at $322.49. Fitting a seal yourself means sealant that Pentair says to leave overnight to cure.
- Volute kit, 357243z. The whole strainer pot assembly, for a cracked pot.
On a salt pool or a system with ozone, ask for the resistant shaft seal, 071732s, or the seal plate kit built with it, 350199.
The unions aren't included with the pump. They're kit 357603.
The drive is the expensive part
The seals, o-rings and basket cost a few dollars each. The drive and motor don't:
- Drive, after late 2020 (356944z): $1,902.12 US list
- Drive, before late 2020 (356880z): $2,059.50
- Drive assembly with the keypad (356971z or 356922z): $2,477.20 or $2,477.21
- Motor (350305s): $1,566.62
Before you price a drive, rule out the problems Pentair's manual fixes for free:
- Overheat. Above 130°F inside the drive, the pump slows down until it cools. Pentair says to shade the motor, ventilate any enclosure and leave at least 3 inches behind the motor fan.
- Low voltage. Check the voltage at the motor terminals while the pump runs. If it's below 90% or above 110% of the rating, Pentair says to call a licensed electrician.
- A flickering screen. Check that the connection between the drive and the keypad is tight.
If the drive really has failed, get a price for a whole new pump before you order one, so you're choosing between two real numbers.
Settings that look like faults
Priming is on by default, and turning it off takes two steps. With the pump on Pentair automation, priming has to be disabled on both the automation and the pump. Pentair's order is to disable it on the automation, unplug the RS-485 cable, disable it on the pump, then plug the cable back in. The pump obeys its own settings at startup before it takes commands.
If it won't come out of priming, raise the priming range. If it leaves priming with air still in the pot, lower it. The range runs 1 to 10, and the default is 5. A pump that can't prime within the maximum priming time, 11 minutes by default, stops for 10 minutes and tries again. After five failed tries it needs a manual reset.
Thermal mode isn't freeze protection. Its sensor is in the drive, not in the air or the water, and it's there to protect the pump. Its defaults are 1,000 RPM, starting when the drive reads 40°F. The pump's own thermal protection is also off whenever it's on an automation system, so freeze protection has to come from the automation.
A warning light isn't always a fault. In a flow program, the pump stops speeding up when it reaches the maximum pressure setting, 30 psi by default. The flow it was asked for doesn't arrive, and a warning light comes on. The warning means a setting or a restriction is in the way, such as a dirty filter. Low pool water pressure covers finding the restriction.
It's 230 V only. The IntelliFlo VSF won't run on a 115 V circuit. That matters if you replace it, because the IntelliFlo3's 1.5 HP model takes either voltage.
The IntelliPro VSF is a different pump
Pentair also sold an IntelliPro VSF, item 013004, under its Sta-Rite name, and it's discontinued too. Its brochure describes it the same way, but its manual, P/N 356654, shows a different wet end: its own trap body, V-clamp, impeller, diffuser and seal. None of the wet-end parts on this page fit it.
It shares a few parts with the IntelliFlo VSF: the black motor (350306s), the drive hardware kit (355685), the black keypad relocation kit (356905z) and the communication cable. Its drive is its own, 356657z, in drive kit 353141z.
Pentair's own pages disagree on its efficiency. The IntelliPro VSF page says WEF 6.6 at the top and 6.9 in its table. Its manual says 6.6.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Impeller | Diffuser | Drive | Drive kit |
|---|---|---|---|---|---|
| IntelliFlo VSF, built before late 2020 | 011056 | 073131z | 072928z | 356880z | 356922z |
Note on IntelliFlo VSF, built before late 2020: The manual splits these parts at November 2020 and Pentair's 2025–2026 catalog at October 2020. Pentair doesn't say whether the later impeller, diffuser or drive fits an earlier pump, so confirm which you have with a Pentair dealer before ordering. The earlier impeller and diffuser are the same numbers as the 3 HP WhisperFlo's. | |||||
| IntelliFlo VSF, built after late 2020 | 011056 | 356237 | 356238 | 356944z | 356971z |
Note on IntelliFlo VSF, built after late 2020: The same item number with a new impeller, diffuser and drive. Pentair's catalog lists the new impeller and diffuser at CALL rather than a price. | |||||
Pentair IntelliFlo VSF parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
Pentair's chart lists a defective strainer gasket under a pump that won't prime, and its fix for a suction air leak starts with securing the lid and checking the gasket is in place. The maintenance section says to keep the o-ring clean and well lubricated, and to turn the locking ring until its handles sit perpendicular to the inlet. $6.04 US list.
A clogged basket is on Pentair's chart under both. The guide says to look at it through the lid at least once a week, replace it if it's cracked, and line up the notch in its bottom with the rib in the bottom of the volute when it goes back in. $26.77 US list.
Two halves: a ceramic seat that turns in the impeller and a spring seal that sits still in the seal plate. Their polished faces leak if they're scratched, so the guide says to handle them with care. The spring half goes into the seal plate with silicone sealant on its metal part, kept off the faces, and Pentair says to let it cure overnight before reassembling. 071732s is the ozone and salt resistant version. $48.53 US list, or $40.66 for 071732s.
The guide's warning is specific. The gasket can get pinched between the seal plate and the housing while the six bolts are tightened, and then the pump leaks slowly when it restarts. Grease it before reassembly, start the two through bolts first for alignment, and finger-tighten all six before tightening any. $10.34 US list.
Pentair's chart blames a clogged impeller for reduced capacity, and gravel or metal in it for a noisy motor. To clear it, the guide takes the strainer pot off the seal plate, then the diffuser, then the impeller. The impeller screw is a left-hand thread that loosens clockwise, and a 1/4-inch Allen wrench in the end of the motor shaft, through the fan cover, holds the shaft still. 073131z is for pumps built before late 2020, at $160.28 US list. Later pumps take 356237, which the catalog prices at CALL.
Check the cheap things before pricing this one. For a flickering screen, Pentair's chart says to check that the connection between the drive and the keypad is tight. After an over current or over voltage alarm, Pentair says the drive restarts 20 seconds after the condition clears. For an internal error, Pentair says to clear the alarm and restart, and to call its technical service if it keeps coming back. 356944z is for pumps built after late 2020, at $1,902.12 US list. Earlier pumps take 356880z, at $2,059.50.
To winterize, the guide says to cut power at the breaker, take out the two thumb-twist drain plugs, drain the pump and store the plugs in the strainer basket. It also says freeze damage isn't covered under warranty. Each plug seals with a 192115z o-ring. $9.85 US list.
If you are doing the job anyway
Pentair names the quick kit for the WhisperFlo and IntelliFlo together, and the seal plate and volute kits carry the same numbers on its WhisperFlo VST list.
Quick kit
The shaft seal, seal plate gasket, diffuser o-ring, lid o-ring, both drain plug o-rings and the impeller screw washer, which is every seal you'd replace with the pump apart. It lists at $53.55. The shaft seal alone lists at $48.53.
- Shaft seal071734s
- Seal plate gasket357100z
- 355227z355227z
- Lid o-ring350013z
- 192115z192115z
- 075713z075713z
Sold as a kit: 356198
Seal plate kit
The seal plate with the shaft seal already in it, plus the gasket. It skips the overnight wait for the seal's sealant to cure. $322.49 US list, or $314.95 for the ozone and salt resistant 350199.
- 074564z074564z
- Seal plate gasket357100z
- Shaft seal071734s
Sold as a kit: 350202
Volute kit
The strainer pot with its clamp, lid, lid o-ring, basket, drain plugs and their o-rings: items 1 to 7. For a cracked pot. $764.82 US list.
- 357199z357199z
- 357151z357151z
- Lid o-ring350013z
- Strainer basket070387z
- 350015z350015z
- 192115z192115z
- Drain plug071131z
Sold as a kit: 357243z
Pentair IntelliFlo VSF manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- IntelliFlo VSF installation and user's guide (P/N 356652 Rev. F, 2020)manual
- Installation and user's guide, Spanishmanual
- Installation and user's guide, Frenchmanual
- Pentair Pool 2025–2026 product catalog, pump parts: the IntelliFlo VSF on page 431, and the drive history on page 427, with US list pricesdiagram
- IntelliFlo VSF replacement parts sheet (2019)diagram
- IntelliFlo VSF brochure, with the performance curves (2020)curves
- IntelliFlo VSF product page, with the item number tablespec
- IntelliPro VSF product pagespec
- IntelliPro VSF installation and user's guide (P/N 356654 Rev. F, 2021)manual
Pentair IntelliFlo VSF warranty
3 years parts
Three years. Pentair's warranty page puts the IntelliFlo VSF on one line with the IntelliFloXF VSF at that term. On a discontinued pump the term matters less than the clauses. Coverage starts on the installation date, not the purchase date, and passes to the next owner with proof of purchase while the pump stays where it was installed. Pentair counts pump mechanical seals, o-rings, gaskets and strainer baskets as consumables, with one year of parts and labor. Bought online, the warranty page gives one year, parts only, from the date of purchase. Pentair's 2020 brochure called the pump TradeGrade, but 011056 isn't on the TradeGrade list revised October 23, 2026. The manual adds that undiluted chemicals added in front of the pump's suction void the warranty, that water or dirt damage may void the motor warranty, and that freeze damage isn't covered.
Manufacturer’s termsPentair IntelliFlo VSF complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
45 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 357199z | Clamp, cam and ramp | Almond. $76.56 US list. Black: 357150 |
| 2 | 357151z | See-through lid | $57.49 US list |
| 3 | 350013z | Lid o-ring what goes wrong | $6.04 US list |
| 4 | 070387z | Strainer basket what goes wrong | $26.77 US list |
| 5 | 350015z | Volute | Almond. $366.49 US list. Black: 357157 |
| 6 | 192115z | O-ring 112, drain plug | 2 required. $4.04 US list |
| 7 | 071131z | Drain plug what goes wrong | 2 required. Almond. $9.85 US list. Black: 357161 |
| 8 | 357243z | Volute kit | Includes items 1 to 7. Almond. $764.82 US list. Black: 357244 |
| 9 | 071406z | Nut, 1/4-20 hex, stainless | 2 required. $2.60 US list |
| 10 | 072183 | Washer, flat, 1/4 in. ID x 5/8 in. OD | 2 required. The 2019 parts sheet prints 072186; the 2020 manual 072183 |
| 11 | 071657 | Screw, 1/4-20 x 1 in. hex cap, stainless | 2 required |
| 12 | 070927z | Foot | Almond. $61.41 US list. Black: 357159 |
| 13 | 070929z | Foot insert, pump motor support | Almond. $30.82 US list. Black: 357160 |
| 14 | 070429z | Bolt, 3/8-16 x 7/8 in. hex head | 4 required. $5.03 US list |
| 15 | 070430z | Bolt, 3/8-16 x 1-1/4 in. hex head | 4 required. $4.02 US list |
| 16 | 072184 | Washer, flat, 3/8 in. ID x 7/8 in. OD | 6 required. $2.48 US list |
| 17 | 070431 | Bolt, 3/8-16 x 2 in. hex head | 2 required |
| 18 | 350305s | Motor, 3.2 kW, 10 pole | Almond. $1,566.62 US list. Black: 350306s |
| 19 | 356880z | Drive, variable speed | Pumps built before late 2020. Almond. $2,059.50 US list. Black: 356894z |
| 19 | 356944z | Drive, variable speed what goes wrong | Pumps built after late 2020. Almond. $1,902.12 US list. Black: 356992z. The manual labels this row 'before 11/20' as well; the catalog says after |
| 20 | 357527z | Drive cover kit, with keypad cover | Includes item 21. The catalog calls it the keypad assembly kit. Almond. $592.10 US list. Black: 358527z |
| 21 | 400100 | Keypad cover | Almond. $346.76 US list. Black: 401100 |
| 22 | 356904z | Keypad relocation kit | Relocation cable and blank drive cover, for mounting the keypad on a wall. Almond. $118.87 US list. Black: 356905z |
| 23 | 355685 | Drive hardware kit | Drive screws, drive gasket and screw caps |
| 24 | 074564z | Seal plate | Almond. $174.06 US list. Black: 357158 |
| 25 | 357100z | Seal plate gasket what goes wrong | $10.34 US list |
| 26 | 071734s | Mechanical seal what goes wrong | $48.53 US list |
| 26 | 071732s | Mechanical seal, ozone and salt resistant | The alternative for item 26. $40.66 US list |
| 27 | 073131z | Impeller what goes wrong | Pumps built before late 2020. $160.28 US list |
| 27 | 356237 | Impeller | Pumps built after late 2020. The catalog's price is CALL |
| 28 | 075713z | Rubber washer, impeller set screw | $2.89 US list |
| 29 | 071652z | Impeller set screw, 1/4-20, left-hand thread | $5.03 US list |
| 30 | 072928z | Diffuser | Pumps built before late 2020. $60.48 US list |
| 30 | 356238 | Diffuser | Pumps built after late 2020. The catalog's price is CALL |
| 31 | 071660 | Diffuser set screw, 4-40 x 1-1/8 in. | 2 required |
| 32 | 355227z | Diffuser o-ring | $5.21 US list |
| 33 | 071403 | Nut, 3/8-16 brass, nickel plated | 2 required. The 2019 parts sheet prints 071404; the 2020 manual 071403 |
| 34 | 356922z | Drive assembly | Items 19 to 21 and 23. Pumps built before late 2020. Almond. $2,477.21 US list. Black: 355868z |
| 34 | 356971z | Drive assembly | Items 19 to 21 and 23. Pumps built after late 2020. Almond. $2,477.20 US list. Black: 356991z |
| — | 350122z | Communication cable, 50 ft | Not shown. $271.62 US list |
| — | 350202 | Seal plate kit with mechanical seal | Items 24 to 26. Not shown. Almond. $322.49 US list. Black: 350203 |
| — | 350199 | Seal plate kit, ozone and salt resistant | Not shown. Almond. $314.95 US list. Black: 350198 |
| — | 357603 | Union kit | Two complete unions for one pump, not included with it. Almond only. $178.84 US list |
| — | 356198 | WhisperFlo/IntelliFlo quick kit | Items 3, 6 (two), 25, 26, 28 and 32, by the manual's numbers. Catalog only. $53.55 US list |
| — | 352401 | Motor fan kit | Catalog only. $277.95 US list |