Pentair · IntelliFlo VS
Pentair IntelliFlo VS
Pentair's discontinued IntelliFlo VS: its three builds and the parts that differ, the WhisperFlo wet end, and the settings that make it look broken.
Discontinued. Replaced by the IntelliFlo3 VSF, which Pentair names as the recommended replacement. Everything on this page still applies to the units already installed.

The IntelliFlo VS is Pentair's 3 HP variable-speed IntelliFlo without flow control. It holds whatever speed you set, from 450 to 3,450 RPM. Its sibling, the IntelliFlo VSF, can also hold a set flow.
Pentair's product page now marks the VS discontinued, under item number 011028, and names the IntelliFlo3 VSF as its replacement. Its parts aren't discontinued. Pentair's 2025–2026 catalog, updated September 2025, still lists the wet end, both motors and the drive, with prices. This page is for the pump already on your pad.
The manual and brochure give its efficiency under EC-011028. Pentair uses the EC- prefix for products sold online, and those carry its online warranty terms.
Find out which build you have
Pentair's catalog prints two parts pages for this pump. One is for pumps built before 2019, the other for pumps built after 2018. The later build then changed its impeller and diffuser in late 2020: October 2020 in the catalog, November 2020 in the manual. That makes three builds:
- Before 2019. Motor 350105s, power end 070118, impeller 073131z and diffuser 072928z. The drive sits under a drive control cover kit: 350601 on pumps built before December 23, 2013, and 400100z after.
- 2019 to late 2020. Motor 350305s, power end 354044, impeller 073131z and diffuser 072928z, with the keypad assembly kit 357527z. This is the build the 2020 manual describes.
- After late 2020. The same as above, with impeller 356237 and diffuser 356238.
The drive doesn't change. Pentair's drive history table gives 356878z as the current drive, and 356879z as the current drive kit, for every IntelliFlo VS, including the earliest pumps under item number 011018.
Pentair's documents don't say where to read the build date on the pump, or whether a later motor, impeller or diffuser fits an earlier pump. Ask a Pentair dealer to confirm your build before you order any of those.
The wet end is a WhisperFlo's
Most of this pump's wet end carries the WhisperFlo's part numbers: the lid clamp, lid, lid o-ring, basket, volute, drain plugs, shaft seal, seal plate gasket and seal plate kit. On a pump built before late 2020, so do the impeller and diffuser. It's the same wet end as the IntelliFlo VSF's, and Pentair's catalog prints the later build on one page with the VSF.
So the kits are the same too:
- Quick kit, 356198. Every seal and o-ring you'd replace with the pump apart, at $53.55 US list. The shaft seal alone lists at $48.53.
- Seal plate kit, 350202. The seal plate with the shaft seal already pressed in, at $322.49. Fitting a seal yourself means sealant that Pentair says to leave overnight to cure.
- Volute kit, 357243z. The whole strainer pot assembly, for a cracked pot, at $764.82.
- Volute and seal plate kit, 357149. The pot and the seal plate kit together, almond only, at $480.93 on Pentair's list. That's less than the volute kit alone, so ask a dealer to price both.
On a salt pool or a system with ozone, ask for the resistant shaft seal, 071732s, or the seal plate kit built with it, 350199.
The unions aren't included with the pump. They're kit 357603.
The drive is the expensive part
The seals, o-rings and basket cost a few dollars each. The rest doesn't:
- Drive (356878z): $2,059.50 US list
- Drive kit with the keypad (356879z): $2,394.18
- Motor (350305s or 350105s): $1,566.62
- Power end, after 2018 (354044): $3,834.41
Before you price a drive, rule out the problems Pentair's manual fixes for free:
- Overheat. Above 130°F inside the drive, the pump slows down until it cools. Pentair says to shade the motor, ventilate any enclosure and leave at least 3 inches behind the motor fan.
- Low voltage. Below 170 volts the drive shuts down to protect itself. Check the voltage at the motor terminals while the pump runs. If it's below 90% or above 110% of the rating, Pentair says to call a licensed electrician.
- Over voltage with nothing wrong at the panel. Pentair says water turning the pump from outside can cause it. For a pump plumbed in parallel with another, the manual calls for check valves, to stop the impeller and motor turning backward. The pump also won't start while its impeller is turning.
- A flickering screen. Check that the connection between the drive and the keypad is tight.
If the drive really has failed, get a price for a whole new pump before you order one, so you're choosing between two real numbers.
Settings that look like faults
Speeds 3 and 4 turn themselves off. Out of the box they're Egg Timer speeds: press one and start the pump, and it runs for a set time and then stops. Pentair says that's to keep the pump from running above half its maximum speed indefinitely. Speeds 1 and 2 default to Manual, and 3 and 4 can be changed to Manual in the menu.
Time Out holds the pump off. The Time Out button stops the pump for a set period, 3 hours by default, then returns it to its schedule. Quick Clean does the opposite: 3,450 RPM for 10 minutes by default, then back to the schedule.
A schedule doesn't run until Start/Stop is lit. Pentair also says a speed can't have the same start and stop times. To run one around the clock, set the start one minute after the stop. If two scheduled speeds overlap, the pump runs the faster one. Pool pump won't turn on covers the checks outside the pump.
Priming is on by default, and turning it off takes two steps. With the pump on Pentair automation, priming has to be disabled on both the automation and the pump. Pentair's order is to disable it on the automation, unplug the RS-485 cable, disable it on the pump, then plug the cable back in. The pump obeys its own settings at startup before it takes commands.
If it won't come out of priming, raise the priming range. If it leaves priming with air still in the pot, lower it. The range runs 1 to 10, and the default is 5. A pump that can't prime within the maximum priming time, 11 minutes by default, stops for 10 minutes and tries again. After five failed tries it needs a manual reset. If the maximum speed is set below the lowest priming speed, the pump goes over it while priming. Pentair's answer, if that's a problem, is to turn priming off.
Thermal mode isn't freeze protection. Its sensor is in the drive, not in the air or the water, and it's there to protect the pump's electronics. Its defaults are 1,000 RPM, starting when the drive reads 40°F. The pump's own thermal protection is off whenever it's on an automation system, so freeze protection has to come from the automation's freeze setting.
On automation, it wants its own power. Pentair says to feed it straight from the breaker, with no lights or other appliances on that circuit. On a GFCI breaker it should have its own circuit, unless it runs together with a Pentair salt chlorine generator. It's 230 V only, and it can't be connected in series with another pump.
A noise at start-up isn't always the seal
Pentair's troubleshooting chart has a line for a noise that's most evident as the pump starts or slows down. Its fix isn't the pump's mechanical seal. It's the motor's slinger and the rubber seal behind it: inspect them and lubricate the motor shaft's rubber seals.
The chart's other noise causes are the usual ones. Unsupported piping strains the pump, and Pentair says to mount it on concrete, never a wooden platform. Gravel or metal in the impeller means taking the pump apart to clean it. Cavitation means improving the suction, with bigger pipe or fewer fittings. Pool pump making noise goes through all of them.
If you're replacing it
Pentair names the IntelliFlo3 VSF as the replacement. Its 2025–2026 catalog also still sells the IntelliFlo VS+SVRS, item 011057. That's this pump's sibling with a safety vacuum release system built in, with the same 3.95 total horsepower and 6.9 WEF, and a minimum speed of 1,100 RPM where the VS goes down to 450. The VS has no SVRS of its own.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Motor | Power end | Impeller | Diffuser |
|---|---|---|---|---|---|
| IntelliFlo VS, built before 2019 | 011028 | 350105s | 070118 | 073131z | 072928z |
Note on IntelliFlo VS, built before 2019: Pentair's catalog gives this build its own parts page, with its own motor, power end and drive cover parts. The drive cover kit changed on December 23, 2013: 350601 before that date, 400100z after. The earliest pumps carry item number 011018, which Pentair's drive history marks obsolete. It takes the same drive and drive kit as 011028 today. | |||||
| IntelliFlo VS, built 2019 to late 2020 | 011028 | 350305s | 354044 | 073131z | 072928z |
Note on IntelliFlo VS, built 2019 to late 2020: The build the 2020 manual describes. Pentair's catalog splits the impeller and diffuser at October 2020, and the manual at November 2020. | |||||
| IntelliFlo VS, built after late 2020 | 011028 | 350305s | 354044 | 356237 | 356238 |
Note on IntelliFlo VS, built after late 2020: A new impeller and diffuser, which the catalog prices at CALL. Pentair doesn't say whether either fits an earlier pump. | |||||
Pentair IntelliFlo VS parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
Pentair's chart lists a defective strainer gasket under a pump that won't prime, and its fix for a suction air leak starts with securing the lid and checking the gasket is in place. The maintenance section says to keep the o-ring clean and well lubricated, and to turn the locking ring until its handles sit perpendicular to the inlet. $6.04 US list.
A clogged basket is on Pentair's chart under both. The guide says to look at it through the lid at least once a week, replace it if it's cracked, and line up the notch in its bottom with the rib in the bottom of the volute when it goes back in. $26.77 US list.
Pentair's guide says a pump run dry damages this seal and starts leaking, and that the damaged seal then has to be replaced. Two halves: a ceramic seat that turns in the impeller and a spring seal that sits still in the seal plate. Their polished faces leak if they're scratched. The spring half goes into the seal plate with silicone sealant on its metal part, kept off the faces, and Pentair says to let it cure overnight before reassembling. 071732s is the ozone and salt resistant version. $48.53 US list, or $40.66 for 071732s.
The guide's warning is specific. The gasket can get pinched between the seal plate and the housing while the six bolts are tightened, and then the pump leaks slowly when it restarts. Grease it before reassembly, start the two through bolts first for alignment, and finger-tighten all six before tightening any. $10.34 US list.
Pentair's chart blames a clogged impeller for reduced capacity, and gravel or metal in it for a noisy motor. To clear it, the guide takes the strainer pot off the seal plate, then the diffuser, then the impeller. The impeller screw is a left-hand thread that loosens clockwise, and a 1/4-inch Allen wrench in the end of the motor shaft, through the fan cover, holds the shaft still. 073131z is for pumps built before late 2020, at $160.28 US list. Later pumps take 356237, which the catalog prices at CALL.
Check the cheap things before pricing this one. For a flickering screen, Pentair's chart says to check that the connection between the drive and the keypad is tight. After an over current or over voltage alarm, the drive restarts 20 seconds after the condition clears, and Pentair says an over voltage alarm can come from water turning the pump from outside. For an internal error, Pentair says to clear the alarm and restart, and to call its technical service if it keeps coming back. Every build takes this drive, at $2,059.50 US list, or the drive kit with the keypad, 356879z, at $2,394.18.
Pentair's chart gives four checks before anything is replaced: the cable is connected at both ends, the pump's address matches the one the automation uses, the pump has a circuit name on the automation, and the pump's screen says DISPLAY NOT ACTIVE. It adds that one defective device can stop the whole network, so disconnect devices one at a time until it works. The 50 ft cable comes with the pump. $271.62 US list.
To winterize, the guide says to cut power at the breaker, take out the two thumb-twist drain plugs, drain the pump and store the plugs in the strainer basket. It also says freeze damage isn't covered under warranty. Each plug seals with a 192115z o-ring. $9.85 US list.
If you are doing the job anyway
Pentair names the quick kit for the WhisperFlo and IntelliFlo together, and the 2020 manual lists the volute and seal plate kit for this pump in almond only.
Quick kit
The shaft seal, seal plate gasket, diffuser o-ring, lid o-ring, both drain plug o-rings and the impeller screw washer, which is every seal you'd replace with the pump apart. It lists at $53.55. The shaft seal alone lists at $48.53.
- Shaft seal071734s
- Seal plate gasket357100z
- 355227z355227z
- Lid o-ring350013z
- 192115z192115z
- 075713z075713z
Sold as a kit: 356198
Seal plate kit
The seal plate with the shaft seal already in it, plus the gasket. It skips the overnight wait for the seal's sealant to cure. $322.49 US list, or $314.95 for the ozone and salt resistant 350199.
- 074564z074564z
- Seal plate gasket357100z
- Shaft seal071734s
Sold as a kit: 350202
Volute kit
The strainer pot with its clamp, lid, lid o-ring, basket, drain plugs and their o-rings: items 1 to 7. For a cracked pot. $764.82 US list.
- 357199z357199z
- 357151z357151z
- Lid o-ring350013z
- Strainer basket070387z
- 350015z350015z
- 192115z192115z
- Drain plug071131z
Sold as a kit: 357243z
Volute and seal plate kit
Items 1 to 7 and the seal plate kit together, almond only. On Pentair's catalog it lists at $480.93, less than the volute kit alone. Confirm the price with a dealer before choosing between them.
- 357199z357199z
- 357151z357151z
- Lid o-ring350013z
- Strainer basket070387z
- 350015z350015z
- 192115z192115z
- Drain plug071131z
- 074564z074564z
- Seal plate gasket357100z
- Shaft seal071734s
Sold as a kit: 357149
Pentair IntelliFlo VS manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- IntelliFlo variable speed pump installation and user's guide (P/N 356919 Rev. C, 2020)manual
- Installation and user's guide, Spanishmanual
- Pentair Pool 2025–2026 product catalog, pump parts: the build after 2018 on page 431, the build before 2019 on page 433, and the drive history on page 427, with US list pricesdiagram
- IntelliFlo VS and VS+SVRS replacement parts list, the build before 2019 (2020)diagram
- IntelliFlo variable speed pump brochure, with the performance curves (2020)curves
- IntelliFlo VS product page, with the item number tablespec
Pentair IntelliFlo VS warranty
Two years, on Pentair's row for first-generation IntelliFlo pumps
Pentair's warranty page doesn't name the IntelliFlo VS. Its row for IntelliFlo and IntelliPro pumps of the first generation gives two years, a year less than the IntelliFlo VSF and IntelliFlo 2 VST rows. On a discontinued pump the clauses matter more than the term. Coverage starts on the installation date and passes to the next owner with proof of purchase while the pump stays where it was installed. Pentair counts pump mechanical seals, o-rings, gaskets and strainer baskets as consumables, with one year of parts and labor. A pump that needed professional installation and didn't get it has one year, parts only. So does one bought online, counted from the date of purchase. Pentair's product page shows the TradeGrade logo, but 011028 isn't on the TradeGrade list revised October 23, 2026. The manual adds that undiluted chemicals added in front of the pump's suction void the warranty, that water or dirt damage may void the motor warranty, and that freeze damage isn't covered.
Manufacturer’s termsPentair IntelliFlo VS complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
52 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 357199z | Clamp, cam and ramp | Almond. $76.56 US list. Black: 357150 |
| 2 | 357151z | See-through lid | $57.49 US list. The catalog's page for the build before 2019 adds a chemical resistant lid, 357156, at $108.44 |
| 3 | 350013z | Lid o-ring what goes wrong | $6.04 US list |
| 4 | 070387z | Strainer basket what goes wrong | $26.77 US list |
| 5 | 350015z | Volute | Almond. $366.49 US list. Black: 357157 |
| 6 | 192115z | O-ring 112, drain plug | 2 required. $4.04 US list |
| 7 | 071131z | Drain plug what goes wrong | 2 required. Almond. $9.85 US list. Black: 357161 |
| 8 | 357243z | Volute kit | Includes items 1 to 7. Almond. $764.82 US list. Black: 357244 |
| 9 | 071406z | Nut, 1/4-20 hex, stainless | 2 required. $2.60 US list |
| 10 | 072183 | Washer, flat, 1/4 in. ID x 5/8 in. OD | 2 required. The catalog lists it as 072183z at $2.48 on its page for the build before 2019 |
| 11 | 071657 | Screw, 1/4-20 x 1 in. hex cap, stainless | 2 required. The catalog lists it as 071657z at $5.03 on its page for the build before 2019 |
| 12 | 070927z | Foot | Almond. $61.41 US list. Black: 357159 |
| 13 | 070929z | Foot insert, pump motor support | Almond. $30.82 US list. Black: 357160 |
| 14 | 070429z | Bolt, 3/8-16 x 7/8 in. hex head | 4 required. $5.03 US list |
| 15 | 070430z | Bolt, 3/8-16 x 1-1/4 in. hex head | 4 required. $4.02 US list |
| 16 | 072184 | Washer, flat, 3/8 in. ID x 7/8 in. OD | 6 required. $2.48 US list |
| 17 | 070431 | Bolt, 3/8-16 x 2 in. hex head | 2 required |
| 18 | 350305s | Motor, 3.2 kW, 10 pole | Pumps built after 2018. Almond. $1,566.62 US list. Black: 350306s |
| 18 | 350105s | Motor, 3.2 kW, permanent magnet | Pumps built before 2019, from the catalog's page 433. Almond. $1,566.62 US list |
| 19 | 356878z | Drive, variable speed what goes wrong | Every build, per the catalog's drive history. Almond. $2,059.50 US list. Black: 356892z |
| 20 | 357527z | Drive cover kit, with keypad cover | Includes item 21. The catalog calls it the keypad assembly kit. Almond. $592.10 US list. Black: 358527z |
| 21 | 400100 | Keypad cover | Almond. $346.76 US list. Black: 401100 |
| 22 | 356904z | Keypad relocation kit | Relocation cable and blank drive cover, for mounting the keypad on a wall. Almond. $118.87 US list. Black: 356905z |
| 23 | 355685 | Drive hardware kit | Drive screws, drive gasket and screw caps. Not priced on the catalog's page for this pump |
| 24 | 074564z | Seal plate | Almond. $174.06 US list. Black: 357158 |
| 25 | 357100z | Seal plate gasket what goes wrong | $10.34 US list. The catalog's page for the build before 2019 also lists an almond gasket, 357102z, at CALL |
| 26 | 071734s | Mechanical seal what goes wrong | $48.53 US list |
| 26 | 071732s | Mechanical seal, ozone and salt resistant | The alternative for item 26. $40.66 US list |
| 27 | 073131z | Impeller what goes wrong | Pumps built before late 2020. $160.28 US list |
| 27 | 356237 | Impeller | Pumps built after late 2020. The catalog's price is CALL |
| 28 | 075713z | Rubber washer, impeller set screw | $2.89 US list |
| 29 | 071652z | Impeller set screw, 1/4-20, left-hand thread | $5.03 US list |
| 30 | 072928z | Diffuser | Pumps built before late 2020. $60.48 US list |
| 30 | 356238 | Diffuser | Pumps built after late 2020. The catalog's price is CALL |
| 31 | 071660 | Diffuser set screw, 4-40 x 1-1/8 in. | 2 required |
| 32 | 355227z | Diffuser o-ring | $5.21 US list |
| 33 | 071403 | Nut, 3/8-16 brass, nickel plated | 2 required. The catalog's price is CALL |
| 34 | 356879z | Drive kit | Items 19 to 21 and 23. Every build, per the catalog's drive history. Almond. $2,394.18 US list. Black: 356893z |
| — | 350122z | Communication cable, 50 ft what goes wrong | Not shown. Included with the pump. $271.62 US list |
| — | 350202 | Seal plate kit with mechanical seal | Items 24 to 26. Not shown. Almond. $322.49 US list. Black: 350203 |
| — | 350199 | Seal plate kit, ozone and salt resistant | Catalog only. $314.95 US list |
| — | 357149 | Volute and seal plate kit | Items 1 to 7 and 24 to 26. Almond only. $480.93 US list |
| — | 354044 | Power end, 3 HP | Pumps built after 2018. Almond only. $3,834.41 US list |
| — | 070118 | Power end | Pumps built before 2019, from the catalog's page 433, which prices it at CALL |
| — | 357603 | Union kit | Two complete unions for one pump, not included with it. $178.84 US list |
| — | 356198 | WhisperFlo/IntelliFlo quick kit | Items 3, 6 (two), 25, 26, 28 and 32, by the manual's numbers. Catalog only. $53.55 US list |
| — | 352401 | Motor fan kit | Catalog only. $277.95 US list |
| — | 350601 | Drive control cover kit | Pumps built before December 23, 2013, from the catalog's page 433. Almond. $346.76 US list |
| — | 400100z | Drive control cover kit | Pumps built from December 23, 2013 until 2019, from the catalog's page 433. Almond. $346.76 US list, the same as keypad cover 400100, item 21. Pentair doesn't say whether they're the same part |
| — | 350612 | Drive hardware and gasket kit | Three screws, three spacer caps and the drive gasket. Pumps built before 2019. $173.56 US list |
| — | 350108z | Drive gasket | Pumps built before 2019. $13.92 US list |
| — | 350621z | Junction box cover | Pumps built before 2019. Almond. $32.49 US list |