Pentair · System:3
Pentair Sta-Rite System:3 Sand
Sta-Rite's System:3 sand filter in two sizes: the tank it shares with the D.E. and cartridge filters, the sand it takes, and the part numbers that changed.

The System:3 SS Series is Sta-Rite's sand filter, sold by Pentair, which owns the Sta-Rite name. It comes in two sizes, the S7S50 and the S8S70, and Pentair's page lists both as current, through dealers. Like the rest of the System:3 family, it's a two-piece black tank split down the middle and held by Posi-Lok clamps, and Pentair says the modular tanks let you change filter media without changing the tank.
Its siblings are the System:3 D.E. filter and the System:3 cartridge filter. Sand, cartridge or D.E. covers how the three types compare.
Two sizes, two tanks
- S7S50: 2.4 square feet, 33 to 48 gallons a minute, 200 pounds of sand. A 21-inch tank with 7 clamps.
- S8S70: 3.4 square feet, 47 to 68 gallons a minute, 300 pounds of sand. A 25-inch tank with 8 clamps.
The S7S50's tank is the D.E. filter's. Its upper half, 24851-9000, cord ring, clamps and bolts carry the same numbers as the System:3 D.E. filter's and the smaller cartridge filters'. The S8S70's cord ring, 24850-0009, is the larger cartridge filters' too. Pentair's catalog lists a sand conversion kit, 25021-2021, for the 21-inch tank, with the collector bought separately.
The sand
Use only #20 silica sand, 0.40 to 0.55 mm, with a uniformity coefficient under 1.75. The manual says other sands reduce performance, can damage the pump, and void the warranty, and not to use anything finer.
The manual's steps for filling it:
- Look inside first for broken or loose laterals, and replace any you find.
- Fill the tank half full of water before the sand goes in. That takes the strain off the laterals.
- Pour in the sand until its top is about 12-1/2 inches below the top of the distributor, about 1-1/2 inches below the tank flange. That leaves 11 inches of freeboard below the backwash outlet.
- Wash all sand off the cord ring's seat before the top goes back on.
Inspect the sand bed at least once a year. When the top of the bed turns hard and crusty, replace all the sand.
Backwashing it
Backwash when the gauge reads 10 psi above the starting pressure. Each backwash sends 100 gallons or more to waste, so make sure where it goes is legal and won't flood anything. Always switch the pump off before you move the valve.
With a multiport valve:
- Pump off, valve to BACKWASH, air release valve open.
- Start the pump, and close the air release valve when a steady stream comes out.
- Backwash until the water runs clear.
- Pump off, valve to RINSE, then run the pump for a minute.
- Pump off, valve to FILTER, release the pressure, and restart.
With a slide valve, the handle goes up for backwash and down, pinned, for filter. There's no rinse.
Use one of the valves the manual names. It lists the 2-inch and 1-1/2-inch multiport valves, 18202-0200 and 18202-0150, and the brass and plastic 2-inch slide valves, WC212-136D and WC212-134P, and warns that any other valve could send water backward through the filter and damage its internals. Pentair's product page lists 18202-0150, 18201-0200, 263053 and 262508 beside the filters.
Opening the tank
Before you loosen anything, stop the pump, open the air release valve and the drain, and wait for all the pressure and water to go. The manual warns that adjusting a clamp under pressure will blow the tank off its base.
To drain it, hold the bottom drain fitting firmly in the tank while you take its plug out, so the sand stays put. The side plug is for emptying sand only.
Loosen the clamps on opposite sides in turn, and lift the top half off without damaging the cord ring. Putting it back, inspect the cord ring, clean both seats, and don't lubricate it. Tighten the clamps securely hand-tight in the crisscross order the manual draws, never working your way around the tank from one clamp to the next.
Sand in the pool
The manual's troubleshooting says sand in the pool means a broken lateral. Pentair's parts sheet shows a repair with the lateral extension adapter, 24700-0029: cut the broken lateral off square close to the break, cut a new one to length, and solvent weld them to the adapter with the solvent the sheet names, #771, its slots lined up with the lateral's ribs. Allow an hour before the sand goes back and 24 hours before the filter runs, and follow the cement maker's instructions exactly. Otherwise replace the lateral, or the whole collector, 24900-0100S on the S7S50 at $969.42. Sand in the pool covers the other causes.
Installing it
The manual wants the filter as close to the pool as possible, on a level base with drainage, and protected from weather and freezing. Use 2-inch pipe and thread seal tape on plastic threads, never pipe dope, which cracks plastic pipe. Assemble the unions dry and hand-tight, and don't overtighten the ports. A check valve between the filter and a heater stops hot water backing up into the filter.
Pentair's page and brochure give 104°F as the maximum water temperature inside the filter for pools and spas. The 2012 manual says 120°F. The lower figure is the newer one.
Winter
Open the air release valve and all the system valves, and set a multiport valve between positions so air reaches every port. Take the drain plugs out of the pump, trap, valve and filter, drain the piping, and cover the equipment to keep the weather off.
Where you buy it
Pentair sells both sizes through dealers. From a store, builder or service company and professionally installed, the filter gets two years, parts and labor. Without a professional install, or bought online, it's one year, parts only.
Which model do you have?
The model number is on the filter label. Everything else in the range is shared — these are the parts that change with it.
| Model | Area | Max flow | Sand | Cord ring | Lateral |
|---|---|---|---|---|---|
| S7S50 | 2.4 sq. ft. | 48 GPM | 200 lb | 24850-0008Z | 24900-0002 |
Note on S7S50: The 21 in. tank, with 7 clamps: the same upper half, cord ring, clamps and bolts as the System:3 D.E. filter and the smaller cartridge filters. | |||||
| S8S70 | 3.4 sq. ft. | 68 GPM | 300 lb | 24850-0009 | 24901-0003 |
Note on S8S70: The 25 in. tank, with 8 clamps. Its cord ring is the larger cartridge filters' too. | |||||
Pentair Sta-Rite System:3 Sand parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The seal between the tank halves, the same part as the System:3 D.E. filter's. Take it off slowly so it doesn't stretch or tear, replace it if it's cut, nicked, misshapen or has lost its spring, and clean both halves' seats. Don't lubricate it: the manual says lubricant attracts grit, can damage it and voids the warranty. $96.60 US list. The S8S70 takes 24850-0009 at $110.24.
Sixteen of these spokes collect the water at the bottom of the sand bed. The manual's troubleshooting says sand in the pool means a broken one. The 2016 parts sheet draws a repair: cut the broken one off square close to the break, cut a new lateral to length, and solvent weld the two together with the extension adapter, 24700-0029, lining its slots up with the lateral's ribs. Allow an hour before the sand goes back and 24 hours before the filter runs. $18.59 US list. The S8S70's is 24901-0003 at $21.11.
The collector with all sixteen laterals, as one part, at $969.42 US list. The S8S70's is 24901-0100S, which the 2025-2026 catalog doesn't price. To change it, empty the sand, unscrew the two tank fittings counterclockwise, lift the old one out, twist-lock the new laterals into its hub, fit new O-rings on the tank fittings and screw them back in.
The Posi-Lok clamps: seven on the S7S50, eight on the S8S70. Never touch them with the filter under pressure: the manual warns the tank will blow off its base. Tighten them securely hand-tight in the crisscross order the manual draws, never working your way around the tank from one clamp to the next, and loosen them on opposite sides in turn. $196.50 US list each; the bolt is 24850-0010Z at $47.59 and the retaining ring 24850-0016Z at $10.84.
The 2 in. gauge, the air release valve and the fittings between them. Write down the gauge reading with the filter running clean: backwash when it's 10 psi higher. $150.44 US list; the gauge alone is 33600-0023TZ at $72.10.
The small blue filter on the top of the vent tube inside the tank. The manual says to bleed the air from the filter every time the pump stops and starts. $23.10 US list.
The side plug, for taking the sand out only. To drain water, hold the bottom drain fitting, 24900-0505Z at $39.40, firmly in the tank and take out its plug: the manual says holding it stops the sand coming with the water. $42.97 US list.
Items 12 to 18: the O-rings, sand removal plug, drain fitting, plug and tank fittings. The catalog says the collector, item 7, has to be bought separately. $274.01 US list. The 2016 sheet lists the 25 in. tank's kit as 25021-2025.
If you are doing the job anyway
Both jobs open the tank and put the cord ring in your hand. The S8S70 takes cord ring 24850-0009 and lateral 24901-0003. Numbers carry the Z the 2025-2026 catalog prints where it lists the part.
Broken lateral, S7S50
Sand in the pool means a broken lateral. The extension adapter is the part Pentair lists for repairing one, and the tank has to open to reach it.
- Lateral, S7S5024900-0002
- 24700-002924700-0029
- Cord ring, S7S5024850-0008Z
Sand change, S7S50
The sand comes out through the side plug, which seals with this O-ring, and the cord ring comes off when the tank opens.
- Cord ring, S7S5024850-0008Z
- 35505-1424Z35505-1424Z
Pentair Sta-Rite System:3 Sand manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- System:3 high rate sand filters owner's manual, S7S50 and S8S70 (S282 Rev. C, 2012)manual
- System:3 SS Series product page: both sizes and their valves, dealer onlyspec
- System:3 sand filters for inground pools brochurespec
- Pentair Pool 2025-2026 product catalog, filter parts: the SS Series on page 358, with US list pricesdiagram
- SS Series replacement parts, the older catalog page (PDF 2016)diagram
- Pentair pool and spa equipment warranty informationspec
Pentair Sta-Rite System:3 Sand warranty
2 years parts, Included when bought from a dealer and professionally installed labor
Two years. Pentair's warranty table gives all filters that term, for one bought from a store, builder or service company and professionally installed. Without a professional install it's one year, parts only, and anything bought online, including from an authorized online reseller, gets one year of parts only from the date of purchase. Neither size is on Pentair's TradeGrade list. The manual adds that using a sand other than the grade it specifies, or lubricating the cord ring, voids the warranty.
Manufacturer’s termsPentair Sta-Rite System:3 Sand complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
50 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 33600-0023TZ | Gauge, 2 in. | $72.10 US list. Printed 33600-0023T in the manual |
| 2 | 154689Z | Valve assembly, air release | $45.64 US list. The 2012 manual gives WC212-120P |
| 2 | WC212-120P | Valve assembly, air release | The 2012 manual's number |
| — | U212-252DS | Brass deluxe air bleed, optional | The 2016 sheet |
| 3 | 35202-0959Z | Nipple | $21.10 US list. The 2012 manual gives U37-16P |
| 3 | U37-16P | Nipple | The 2012 manual's number |
| 4 | 24900-0504Z | Adapter bushing | $28.09 US list |
| 5 | 35505-1423Z | O-ring | $3.22 US list |
| 6 | 24851-9000 | Tank, upper half kit, S7S50 | Includes all decals and labels. $1,505.28 US list |
| 6 | 24851-9001 | Tank, upper half kit, S8S70 | $1,851.53 US list |
| 7 | 24900-0100S | Collector assembly, with laterals, S7S50 what goes wrong | $969.42 US list |
| 7 | 24901-0100S | Collector assembly, with laterals, S8S70 | The manual and the 2016 sheet; not priced in the 2025-2026 catalog |
| 8 | WC8-126Z | Air bleed filter, blue what goes wrong | $23.10 US list |
| 9 | WC37-386P | Vent tube | The manual and the 2016 sheet |
| 10 | WC78-84P | Elbow, male Parflex | The manual and the 2016 sheet |
| 11 | 24900-0002 | Lateral, S7S50 what goes wrong | Sixteen. $18.59 US list |
| 11 | 24901-0003 | Lateral, S8S70 | Sixteen. $21.11 US list. The 2012 manual prints 24900-0003 |
| 12 | 35505-1424Z | O-ring | Two. $14.92 US list |
| 13 | 24900-0503Z | Plug, sand removal what goes wrong | $42.97 US list |
| 14 | 24900-0505Z | Drain fitting | $39.40 US list |
| 15 | 27001-0022Z | Plug, 1-1/2 in. NPT | $4.45 US list. The 2012 manual prints 27001-0022S |
| 16 | 35505-1425Z | O-ring | Two. $24.90 US list |
| 17 | 24900-0500Z | Tank fitting | $74.87 US list |
| 18 | 24900-0501Z | Tank fitting | $66.72 US list |
| 19 | 24850-0200Z | Clamp assembly what goes wrong | Seven on the S7S50, eight on the S8S70. $196.50 US list |
| 19A | 24850-0010Z | Clamp bolt | $47.59 US list |
| 20 | 24850-0104S | Tank, lower half, S7S50 | The 2016 sheet; the 2012 manual gives 24850-0102S, and the 2025-2026 catalog lists none |
| 20 | 24851-0105S | Tank, lower half, S8S70 | The 2016 sheet; the 2012 manual gives 24851-0103S, and the 2025-2026 catalog lists none |
| 20 | 24850-0102S | Tank, lower half, S7S50 | The 2012 manual's number; the System:3 D.E. filter's lower half |
| 20 | 24851-0103S | Tank, lower half, S8S70 | The 2012 manual's number |
| 21 | 24850-0008Z | Cord ring, S7S50 what goes wrong | $96.60 US list |
| 21 | 24850-0009 | Cord ring, S8S70 | $110.24 US list |
| 22 | 24850-0105 | Valve and gauge assembly, items 1 to 5 what goes wrong | $150.44 US list |
| — | 24850-0016Z | Clamp retaining ring | $10.84 US list |
| — | 24700-0029 | Lateral extension adapter, for lateral repairs | As required. The manual and the 2016 sheet |
| — | 25021-2021 | System:3 sand conversion kit, S7S50, items 12 to 18 what goes wrong | The collector is bought separately. $274.01 US list |
| — | 25021-2025 | System:3 sand conversion kit, S8S70, items 12 to 18 | The 2016 sheet; the collector is bought separately |
| — | 32155-4045 | Decal, model label, S7S50 | The manual; the S8S70's is 32155-4047 |
| — | 32155-4047 | Decal, model label, S8S70 | |
| — | 32165-4004 | Decal, warning, S7S50 | The manual; the S8S70's is 32165-4005 |
| — | 32165-4005 | Decal, warning, S8S70 | |
| — | 32155-4046 | Decal, operating instructions, S7S50 | The manual; the S8S70's is 32155-4048 |
| — | 32155-4048 | Decal, operating instructions, S8S70 | |
| — | 18202-0200 | Multiport valve, 2 in. | The manual's approved valves |
| — | 18202-0150 | Multiport valve, 1-1/2 in. | The manual's approved valves; Pentair's page lists it too |
| — | WC212-136D | Slide valve, 2 in., brass | The manual's approved valves |
| — | WC212-134P | Slide valve, 2 in., plastic | The manual's approved valves |
| — | 18201-0200 | Valve listed on Pentair's SS Series page | No description on the page |
| — | 263053 | Push-pull valve, 7.81 in. centers | Listed on Pentair's SS Series page; described in the 2025-2026 filter catalog |
| — | 262508 | Valve listed on Pentair's SS Series page | No description on the page |