Pentair · SuperMax
Pentair Sta-Rite SuperMax
Sta-Rite's single-speed pump, sold as a drop-in for Hayward's Super Pump: the one US model left, the impeller a TEFC motor needs, and the seal job.

The SuperMax is Sta-Rite's single-speed pool pump. Pentair owns the Sta-Rite name, still sells it, and calls it a direct, drop-in replacement for Hayward's Super Pump. It's the single-speed sibling of the SuperMax VS, and the 348191 shares its motor with the last Max-E-Pro.
One model left in the US
Pentair sells one SuperMax here: the 348191, at 1.10 total horsepower, with a WEF of 3.60 and 0.63 hydraulic horsepower. It's the only one Pentair marks compliant with the Department of Energy's efficiency rule. Every other model on its product page is marked "not for sale in the USA" or built for 50 Hz power abroad. The conversion guide explains why a small single-speed pump like this survived the 2021 rule.
Not in California. The manual says a single-speed pump or motor of 1 total horsepower or more can't be sold, offered or installed for residential pool filtration there. At 1.10, the 348191 is over that line.
The 348191 isn't the old SuperMax with a new motor. Its pot, lid, clamp, basket, seal plate and unions are the older pumps' part numbers. Its impeller, diffuser, impeller screw and shaft seal set are its own, and its motor, 356362S at $695.57 list, is the Max-E-Pro 348185's.
In place of a Hayward Super Pump
That's the job Pentair builds it for: its catalog calls the SuperMax a direct replacement for the Super Pump, and its product page a drop-in. The SuperMax comes with unions for 1½-inch internal slip and 2-inch external slip pipe. Pentair doesn't publish port heights to compare, so offer it up to the old plumbing before cutting anything. Replacing a pool pump covers that check.
Older SuperMax pumps: the impeller a TEFC motor takes
Before 2021 the SuperMax came from 1/2 to 2½ HP, with standard open drip-proof, two-speed, energy-efficient and TEFC motors. Pentair's parts pages for them list motors, impellers and diffusers by horsepower, not by model number, so read your motor's nameplate.
Here's the catch. The 2025-2026 catalog lists one impeller for each horsepower. The pre-2021 manual shows that a TEFC motor takes the next size up:
- 1 HP TEFC: impeller 355074Z and diffuser 355618Z, the 1½ HP standard pump's parts
- 1½ HP TEFC: impeller 355086Z, the 2 HP standard pump's
- 2 HP TEFC: impeller 355093 and diffuser 350170, the 2½ HP standard pump's
Order by the catalog's horsepower line for a TEFC SuperMax and you'd get the wrong impeller. The manual doesn't say which impeller an energy-efficient motor takes, and no document gives one for the 3/4 HP TEFC motor that only the 2025-2026 catalog lists.
The lid, and the basket
The see-through Cam and Ramp lid comes off with a counterclockwise tap on its clamp, and goes back on by turning the clamp clockwise until the handles are horizontal. Before opening it, turn the power off at the breaker and open the filter's air relief valve.
Lubricate the lid o-ring. The SuperMax manual says to keep it clean and well lubricated. That's the opposite of the Max-E-Pro's manual, which says its original o-ring carries its own lubricant and shouldn't be greased. Don't carry the habit from one Sta-Rite pump to the other.
Look at the basket through the lid at least once a week, the manual says. A dirty one cuts flow through the filter and heater and strains the motor. When it goes back, line up the notch in its bottom with the rib in the bottom of the pump. Fill the pot with water up to the inlet before restarting.
Never open the pot of a pump that has failed to prime or run without water. The manual warns it can hold scalding water under vapor pressure. Open the valves and wait until the pot is cool. A pump that won't prime covers the rest.
The shaft seal
Run the pump dry and the seal is damaged and the pump starts leaking; both manuals say so. The older models take seal set 354545S, $45.83 list, or the ozone- and salt-resistant 356210S at $51.07. The 348191 takes 354545SS, priced on request.
The 2021 manual's steps, in short:
- Turn the power off at the breaker, release the system pressure, and drain the pump through its two plugs.
- Take out the four bolts holding the motor and hydraulics to the pot, and ease them apart.
- Remove the diffuser's three screws.
- Hold the motor shaft with a 1/4-inch hex key at the back of the motor. The impeller screw has a left-hand thread and loosens clockwise. Then unscrew the impeller counterclockwise.
- Change the seal, cleaning both halves with soapy water, and take the seal plate off with a 9/16-inch wrench if it needs to come off.
- Reassemble with the shaft threads greased and the impeller hand-tight. Line up the molded line on the diffuser with the one on the seal plate, and grease the diffuser's quad ring and the seal plate o-ring.
- Grease the bolt threads, and finger-tighten all four bolts before tightening any of them fully.
Pentair's 356197 Quick Kit, at $51.94, adds the o-rings and the diffuser seal that job disturbs. A leaking pump covers telling a seal leak from the others.
Where it goes
The 2021 manual sets the limits:
- At least 5 feet from the inside wall of the pool or spa
- At least 3 feet from a heater's outlet
- No more than 10 feet above the water level
- At least 3 inches of space behind the motor, so it can come out
- Not inside an enclosure or under a hot tub's skirt unless the pump is marked for it
Give it a straight run of pipe into the inlet at least 5 times the pipe's diameter, 10 inches on 2-inch pipe, with no elbow right at the pump. Add a check valve on the discharge where the plumbing climbs a long way after the pump, and when two pumps run in parallel.
Winter
Freeze damage isn't covered. Turn the power off, drain the pump through its two plugs, and store the plugs in the basket. Cover the motor against rain and snow, but not with plastic or anything airtight, and never while it might run. In a mild climate, the manual's answer to a brief freeze is to run the equipment all night.
Where you buy it
The 348191 is on Pentair's TradeGrade list, so it's sold through pool stores, builders and service companies. Pentair's warranty table gives single-speed pumps one year and single-phase TEFC Super Duty pumps two, without saying which row the SuperMax falls in. Either term is parts and labor only for a pump bought from a store, builder or service company and professionally installed.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | Impeller | Diffuser | Shaft seal |
|---|---|---|---|---|
| 348191, the DOE model | 1.1 THP | 356356Z | 356358Z | 354545SS |
Note on 348191, the DOE model: The one SuperMax sold in the US, and the only one Pentair marks DOE compliant: a NEMA Premium Efficient TEFC motor at 115/208-230 V, WEF 3.60, 0.63 hydraulic horsepower. Its motor, 356362S, is the one the Max-E-Pro 348185 uses. The pot, lid, clamp, basket, seal plate and unions are the older SuperMax's; the impeller, diffuser and seal set are its own. The 2021 manual covers it. | ||||
| Older SuperMax, 1/2 HP | 0.5 | 355043 | 355617 | 354545S |
Note on Older SuperMax, 1/2 HP: Motors: 355019S standard, 355009S energy efficient. Neither is in the 2025-2026 catalog. | ||||
| Older SuperMax, 3/4 HP | 0.75 | 355043 | 355617 | 354545S |
Note on Older SuperMax, 3/4 HP: Motors: 355019S standard, 355375S two-speed at 115 V, 355009S energy efficient, and 354804S TEFC, the last only in the 2025-2026 catalog. No document gives the TEFC model's impeller. | ||||
| Older SuperMax, 1 HP | 1 | 355067Z; TEFC 355074Z | 355617; TEFC 355618Z | 354545S |
Note on Older SuperMax, 1 HP: Motors: 355021S standard, 355232S two-speed, 355009S energy efficient, 354822S TEFC. | ||||
| Older SuperMax, 1-1/2 HP | 1.5 | 355074Z; TEFC 355086Z | 355618Z | 354545S |
Note on Older SuperMax, 1-1/2 HP: Motors: 355023S standard, 355376S two-speed, 355011S energy efficient, 354824S TEFC. | ||||
| Older SuperMax, 2 HP | 2 | 355086Z; TEFC 355093 | 355618Z; TEFC 350170 | 354545S |
Note on Older SuperMax, 2 HP: Motors: 355025S standard, 355377S two-speed, 355013S energy efficient, 354816S TEFC. | ||||
| Older SuperMax, 2-1/2 HP | 2.5 | 355093 | 350170 | 354545S |
Note on Older SuperMax, 2-1/2 HP: Motors: 355027S standard, 355015S energy efficient. | ||||
Pentair Sta-Rite SuperMax parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The seal on every older SuperMax. Both manuals warn that running dry damages it and the pump starts leaking, and the seal then has to be replaced. Getting to it means pulling the motor and hydraulics off the pot, holding the shaft with a 1/4-inch hex key, and taking the impeller off. $45.83 US list. Pentair's ozone- and salt-resistant version is 356210S at $51.07. The 348191 takes its own set, 354545SS, priced on request.
Pentair's chemical-, salt- and ozone-resistant kit for these pumps: the seal set, the seal bracket o-ring, both drain plug o-rings, the diffuser seal and the lid o-ring. At $51.94 US list on the SuperFlo parts page, it costs $6.11 more than the seal alone, so if the pump is coming apart for the seal, it's the one to order.
The seal under the see-through lid, on every model. The SuperMax manual says to keep it clean and well lubricated, which is the opposite of the Max-E-Pro's, whose o-ring carries its own lubricant. The troubleshooting table names a defective lid gasket for a pump that won't prime. $8.84 US list; the 348191's page prices it on request.
The ring that holds the lid down. Tap it counterclockwise to take it off, and seat it and turn it clockwise until the handles are horizontal. Pentair's warning: air in a serviced system can blow the lid off, so bleed the filter's air relief valve and stand clear when the pump starts. $64.78 US list.
The 2021 manual asks for a look through the lid at least once a week, because a dirty basket cuts flow through the filter and heater and strains the motor. Replace it if it's cracked. When it goes back, line up the notch in its bottom with the rib in the bottom of the pump. $34.93 US list.
The troubleshooting table's answer to reduced flow, once the lines and basket check out, is a clogged impeller. Pull the motor and hydraulics, take out the left-hand impeller screw and its washer, and clear it. The screw loosens clockwise; the impeller itself unscrews counterclockwise. $93.97 US list. The older models' impellers are in the model table.
If you are doing the job anyway
The seal job takes the motor and hydraulics off the pot and the impeller off the shaft, so every o-ring between them is in your hand.
Shaft seal job
Pentair's Quick Kit carries the seal with the o-rings and the diffuser seal the job disturbs, for $6.11 more than the seal alone.
- Seal Quick Kit, SuperFlo and SuperMax356197
Strainer lid that won't seal
The lid o-ring is the cheap first suspect, and the manual wants it lubricated. A clamp that won't lock the lid down is the other part.
- Lid o-ring357255Z
- Clamp, Cam and Ramp, the lid's locking ring351090
Pentair Sta-Rite SuperMax manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- SuperMax installation and user's guide, the 2021 DOE model (P/N 356970 Rev. C, 2023)manual
- SuperMax installation and user's guide, the pre-2021 models (P/N 351096 Rev. R, 2023)manual
- SuperMax product page: the 348191 and the international modelsspec
- SuperMax and Max-E-Pro single-speed pumps brochure, the DOE models (P1-253, 2021)spec
- Pentair Pool 2025-2026 product catalog, pumps: the SuperMax on page 218spec
- Pentair Pool 2025-2026 product catalog, pump parts: the SuperMax on pages 459 to 461, with US list pricesdiagram
- SuperMax replacement parts, the older catalog page (PDF 2016)diagram
- Pentair TradeGrade SKU list (policy effective October 1, 2019)spec
- Pentair pool and spa equipment warranty informationspec
Pentair Sta-Rite SuperMax warranty
One year, or two if Pentair counts it as a TEFC Super Duty pump
Pentair's warranty table gives single-speed pumps one year, and single-phase TEFC Super Duty pumps two; it doesn't say which row the SuperMax falls in. Either way it's parts and labor only when the pump was bought from a store, builder or service company and professionally installed. Bought online, or installed by an owner, it's one year, parts only. The 348191 is on Pentair's TradeGrade list, sold only through stores, builders and service companies. Pump mechanical seals and o-rings are consumables, covered for one year. The manual says freeze damage isn't covered, and that a motor damaged by dirt or water voids the motor warranty.
Manufacturer’s termsPentair Sta-Rite SuperMax complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
60 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 / — | 355019S | Motor, 1/2 and 3/4 HP, standard | The pre-2021 manual and 2016 sheet; not in the 2025-2026 catalog |
| 1 / — | 355009S | Motor, 1/2 to 1 HP, energy efficient | The pre-2021 manual and 2016 sheet; not in the 2025-2026 catalog |
| 1 / — | 355375S | Motor, 3/4 HP two-speed, 115 V | The pre-2021 manual only |
| 1 / — | 354804S | Motor, 3/4 HP TEFC, 115/208-230 V | The 2025-2026 catalog only. $593.93 US list |
| 1 / — | 355021S | Motor, 1 HP standard | $533.24 US list. The catalog prints its voltage as 2115/208-230 |
| 1 / — | 355232S | Motor, 1 HP two-speed, 230 V | Not in the 2025-2026 catalog |
| 1 / — | 354822S | Motor, 1 HP TEFC, 115/208-230 V | $726.14 US list |
| 1 / — | 355023S | Motor, 1-1/2 HP standard | $858.12 US list |
| 1 / — | 355376S | Motor, 1-1/2 HP two-speed, 230 V | Not in the 2025-2026 catalog |
| 1 / — | 355011S | Motor, 1-1/2 HP energy efficient | $618.57 US list |
| 1 / — | 354824S | Motor, 1-1/2 HP TEFC, 208-230 V | $855.29 US list |
| 1 / — | 355025S | Motor, 2 HP standard | Not in the 2025-2026 catalog |
| 1 / — | 355377S | Motor, 2 HP two-speed, 230 V | Not in the 2025-2026 catalog |
| 1 / — | 355013S | Motor, 2 HP energy efficient, 208-230 V | $1,054.77 US list |
| 1 / — | 354816S | Motor, 2 HP TEFC, 208-230 V | $1,019.06 US list |
| 1 / — | 355027S | Motor, 2-1/2 HP standard, 208-230 V | $867.51 US list |
| 1 / — | 355015S | Motor, 2-1/2 HP energy efficient | Not in the 2025-2026 catalog |
| — / 1 | 356362S | Motor, 348191 | The same motor as the Max-E-Pro 348185. $695.57 US list |
| 2 / 2 | 355612Z | Seal plate, black | $139.50 US list |
| 3 / — | 351094 | Base, black | Both manuals; neither catalog page has a row for it |
| — / 3 | 070249 | Bolt, motor, 348191 | Four required. Price on request |
| 4 / 17 | 351090 | Clamp, Cam and Ramp, black what goes wrong | The lid's locking ring. $64.78 US list |
| 5 / 16 | 350091Z | Lid | $52.15 US list |
| 6 / 15 | 357255Z | O-ring, lid, #2-357 what goes wrong | $8.84 US list; price on request on the 348191's page |
| 7 / 13 | 351089 | Volute and strainer pot, black | $438.04 US list |
| 8 / 25 | 350093Z | Union adapter | Two required. $29.12 US list |
| 9 / 24 | 270141Z | Union nut | Two required. $31.27 US list; price on request on the 348191's page |
| 10 / 18 | 192115Z | O-ring, drain plug | Two required. $4.04 US list |
| 11 / 19 | 357161Z | Drain plug | Two required. $8.07 US list |
| — / 21 | 355621 | Bolt, strainer pot | Four required. Both manuals; neither catalog page lists it |
| 12 / 21 | 072184 | Washer, 3/8 in. stainless | Four required. $2.48 US list |
| 14 / 12 | 355619Z | O-ring, seal plate | $17.33 US list; price on request on the 348191's page |
| 15 / 26 | 6020018Z | O-ring, union adapter, #2-226 | Two required. $2.89 US list |
| 16 / 11 | 355030Z | Diffuser seal | $15.00 US list; price on request on the 348191's page |
| 17 / — | 355334Z | Screw, diffuser, #8-32 hex washer head | Older models. Three required. $5.03 US list |
| — / 10 | 356213Z | Screw, diffuser, #8-32 by 7/8 in., 348191 | Three required. $11.28 US list |
| 18 / — | 355617 | Diffuser, 1/2 to 1 HP | Standard motors. $153.69 US list |
| 18 / — | 355618Z | Diffuser, 1-1/2 and 2 HP, and 1 to 1-1/2 HP TEFC | $153.69 US list. The catalog lists it by horsepower only; the pre-2021 manual adds the TEFC sizes |
| 18 / — | 350170 | Diffuser, 2-1/2 HP, and 2 HP TEFC | $151.35 US list |
| — / 9 | 356358Z | Diffuser, 348191 | $146.62 US list |
| 19 / — | 070429Z | Bolt, 3/8-16 by 7/8 in. stainless hex head | Four required. $5.03 US list. The pre-2021 manual's item 19 is U30-74SS |
| 20 / — | 355043 | Impeller, 1/2 and 3/4 HP | $87.14 US list |
| 20 / — | 355067Z | Impeller, 1 HP and 1 HP two-speed | $95.25 US list |
| 20 / — | 355074Z | Impeller, 1-1/2 HP, 1-1/2 HP two-speed and 1 HP TEFC | $95.25 US list. The TEFC fit is the pre-2021 manual's |
| 20 / — | 355086Z | Impeller, 2 HP, 2 HP two-speed and 1-1/2 HP TEFC | $95.25 US list. The TEFC fit is the pre-2021 manual's |
| 20 / — | 355093 | Impeller, 2-1/2 HP and 2 HP TEFC | $92.18 US list. The TEFC fit is the pre-2021 manual's |
| — / 6 | 356356Z | Impeller, 348191 what goes wrong | $93.97 US list |
| 21 / — | 355389Z | Screw, impeller locking | Older models. $3.61 US list |
| — / 8 | 071652Z | Screw, impeller, 348191 | Left-hand thread. $5.03 US list |
| — / 7 | 075713Z | Washer, impeller screw, 348191 | $2.89 US list |
| — / 5 | 356357Z | Hydraulic isolator, 348191 | The 2025-2026 catalog only; the 2021 manual has no row for it. $37.62 US list |
| 22 / — | 354545S | Shaft seal set what goes wrong | Older models. $45.83 US list |
| 22 / — | 356210S | Shaft seal, ozone and salt resistant | Older models. $51.07 US list |
| — / 4 | 354545SS | Shaft seal set, 348191 | Price on request |
| 23 / 14 | 355667Z | Strainer basket, large what goes wrong | $34.93 US list |
| 24 / 23 | 351157 | Union kit, 1-1/2 in. internal by 2 in. external slip | Two each of the nut, adapter and o-ring. $135.49 US list |
| — | 356197 | Seal Quick Kit, SuperFlo and SuperMax, chemical, salt and ozone resistant what goes wrong | The seal set, seal bracket o-ring, two drain plug o-rings, diffuser seal and lid o-ring. $51.94 US list |
| — | 401014Z | Motor end cap and screw | Older models. $41.72 US list |
| — | 357924Z | Fan guard kit, TEFC and Super-Duty | Older models. Price on request |
| — | 357810 | Motor fan guard, 348191 | Price on request |