Pentair · Max-E-Pro
Pentair Sta-Rite Max-E-Pro
Sta-Rite's single-speed pump, now discontinued: which model you have, the parts still listed, the seal job, and the pumps Pentair lines up in its place.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Max-E-Pro is Sta-Rite's single-speed pool pump. Pentair owns the Sta-Rite name, and its product page now marks the Max-E-Pro discontinued. Its 2025-2026 catalog no longer sells the pump, but it still lists the parts: three pages of them, with US list prices. So this page is for keeping one running, and for knowing what to buy when that stops making sense.
Which Max-E-Pro you have
The model number is on the motor's nameplate. There are three families:
- 348185: the last model, built to the Department of Energy's efficiency rule. It has its own parts page and its own manual.
- 348150 to 348153, and 345076 to 345079: the TEFC models, single-phase and three-phase at 208-230/460 V.
- Numbers starting P6: the older generation, at 115/230 V, 230 V, 200/400 V three-phase and 575 V.
The model table below gives each one's motor, impeller, diffuser and base from the 2025-2026 catalog. Where it says none listed, the catalog has no motor for that model. The shaft seal, the strainer lid, the trap body, the band clamp and the seal plate kit are the same on all of them. The two parts diagrams number things differently, so the complete parts list gives the older models' item number first and the 348185's second.
The 2025-2026 catalog dropped a set of older models that Pentair's earlier parts pages, dated 2019, still carry. From those pages:
- 348152, 2 HP single-phase TEFC: motor 354816S, impeller C105-238PEBA
- P6E6C-204L, 1/2 HP: motor AE100CHL, impeller C105-238PX
- P6EA6E-205L, 1 HP: motor AE100ELL, impeller C105-238P
- P6EA6F-206L, 1½ HP: motor AE100FLL, impeller C105-238PB
- P6R6F-207L, 1½ HP: motor 355025S, impeller C105-238PDBA
- P6E6G-208L, 2 HP: motor AE100GHL, impeller C105-238PEBA
- P6EA6G-207L, 2 HP: motor 355025S, impeller C105-238PDBA
- P6R6G-208L, 2 HP: motor 355027S, impeller C105-238PEBA
- P6EAA6G-208L, 2½ HP: motor AE100G5LL, impeller C105-238PEBA
- P6R6H-209L, 3 HP: motor 355034S, impeller C105-238PLA
- 345077, 1½ HP three-phase: motor 354808S, impeller C105-238PDBA
- 345078, 2 HP three-phase: motor 354810S, impeller C105-238PEBA
- P6R62D3-186, 3/4 HP three-phase 200/400 V: motor AP100DH2, impeller C105-238A
- P6R62G3-189, 2 HP three-phase 200/400 V: motor AP100GH2, impeller C105-238PEBA
- P6EA6G36-207, 2 HP at 575 V: motor 62001-1020S, impeller C105-238PDBA
- P6E6H36-209, 3 HP at 575 V: motor 62001-1021S, impeller C105-238PLA
Read those pages with care. They put the impeller screw's number, 37337-6080, in the diffuser column for the four TEFC models, and they spell the square seal plate o-ring 375099Z where the current catalog has 357099Z. The 2025-2026 numbers are the ones to order by.
Why the 348185 was the last
The 2021 federal pump rule left room only for small single-speed pumps. The 348185 is one: 1.10 total horsepower, a WEF of 3.50 and 0.65 hydraulic horsepower, with a NEMA Premium Efficient TEFC motor. Pentair's product page marks it the one DOE-compliant Max-E-Pro. The other models listed there are international versions, most of them marked "not for sale in the USA."
California is stricter. The manual and the catalog both say a single-speed pump or motor of 1 total horsepower or more can't be sold, offered or installed for residential pool filtration there. The 348185 is 1.10. So even the last model was never a California filtration pump.
The ports: 2 inches or 1½?
The manual says the ports take 2-inch NPT pipe inside, with a 3¼-inch buttress thread outside for the union collar, U11-200P. Pentair's product page lists the port size as 1.5 inches for every model. The manual has the detail, so measure yours before buying fittings.
The unions are sold separately: PKG 188 for 2-inch slip and PKG 189 for 2-inch NPT, each with two collars, two o-rings and two adapters. Hand-tighten the collars, and check that each union's o-ring sits in its groove. Use thread seal tape on threaded pipe, never pipe dope, which the manual says can crack the plastic.
The shaft seal, and running dry
The manual's strongest warning is about water level. If the water drops below the suction port, the pump draws air, loses its prime and runs dry. Running dry damages the seal and the pump starts leaking. Keep running it like that, and the case, the impeller and the seal can all be damaged.
The seal, 17351-0101S at $41.75 list, is the same on every model. The manual's replacement steps, in short:
- Turn the power off at the breaker, close the valves, release the pressure and drain the pump.
- Take off the band clamp and pull the motor and seal plate away from the pump body.
- Remove the diffuser's 5 screws, hold the motor shaft with a 1/4-inch hex key at the back of the motor, and unscrew the impeller.
- Take off the seal plate and tap the old white ceramic seal out.
- Press the new ceramic seal in square, wetted with a little liquid detergent, without scratching its face.
- Refit the seal plate at 60 to 80 inch-pounds, slide the rotating half on with its polished carbon face out, and screw the impeller back on.
- Refit the diffuser at 10 to 14 inch-pounds, the band clamp and the drain plug, then prime the pump.
The 356196 Quick Kit, at $48.11, adds the o-rings that job disturbs. A leaking pump covers telling a seal leak from the others.
The strainer lid and priming
Cleaning the basket is the only routine maintenance the manual asks for. Turn the power off and close the valves first, then turn the lid counterclockwise. Put the basket back with its large opening facing the pipe port. The manual says the lid won't fit if the basket goes in backward.
The lid o-ring comes with a permanent internal lubricant, so don't grease it. The lid goes on hand-tight only.
To prime a pump above the water, fill the pot with water, refit the lid, and start it. If it won't prime, check that the valves are open, the suction pipe end is under water and the suction line has no leaks. The manual's warning: never open the pot of a pump that failed to prime or ran without water. It can hold scalding water under vapor pressure. Open the valves and wait until the pot is cool to the touch. A pump that won't prime has the rest.
Winter
Letting the pump freeze damages it and voids the warranty. Drain the pump through its plugs and the piping by gravity. Protect anything that still holds water with propylene glycol, "RV antifreeze," which the manual says is the only antifreeze to use. Its mix for an unprotected pump is 40% antifreeze to 60% water, good to -50°F.
Keep the motor dry and covered, but don't wrap it in plastic, which traps condensation. If you blow the lines out, use only a low-pressure blower, below 5 psi.
Replacing it
Pentair's 2025-2026 catalog lists two riser base kits that line its IntelliFlo3 VSF up with a Max-E-Pro's plumbing: 357832Z for the 1.5 HP IntelliFlo3 and 357833Z for the 3 HP. Other makers plan for the swap too. Hayward's online diagram gives its TriStar VS 800 a riser base for a Max-E-Pro, and Jandy lists the Max-E-Pro with the bases for its VS FloPro.
A new motor is often not an option. For most of the older models the 2025-2026 catalog lists no motor at all, and since the 2025 motor rule, every pool pump motor made from 1.15 to 5 total horsepower has to be variable speed. For those models, a failed motor means a new pump.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | Build | Motor | Impeller | Diffuser | Base |
|---|---|---|---|---|---|---|
| 348185, the DOE model | 1.1 THP | DOE TEFC | 356362S | C105-238PDOEZ | 356359Z | C4-79P, pad C35-43 |
Note on 348185, the DOE model: The last one sold in the US, and the only model on Pentair's product page marked DOE compliant: a NEMA Premium Efficient TEFC motor at 115/208-230 V, WEF 3.50, 0.65 hydraulic horsepower and 10.5/5.5-5.4 full-load amps. Motor 356362S lists at $695.57. It has its own parts page, and its impeller, diffuser and base differ from the older models'. The 2023 manual covers this model, and the impeller number comes from it; the catalog's page leaves it out. | ||||||
| 348150 | 1 | 1-phase TEFC | 354822S | C105-238PBZ | C1-271P1Z | C104-79P, pad C35-44 |
| 348151 | 1.5 | 1-phase TEFC | 354824S | C105-238PDBAZ | C1-271PZ | C104-79P, pad C35-44 |
| 348153 | 3 | 1-phase TEFC | 354818S | C105-238PLA | C1-271PZ | C104-79P, pad C35-44 |
| P6E6D-205L | 0.75 | 115/230 V | None listed | C105-238P | C1-271P1Z | C4-78P, pad C35-43 |
| P6R6D-205L | 0.75 | 115/230 V | None listed | C105-238P | C1-271P1Z | C104-79P, pad C35-44 |
| P6E6E-206L | 1 | 115/230 V | None listed | C105-238PBZ | C1-271P1Z | C4-78P, pad C35-43 |
| P6RA6E-205L | 1 | 115/230 V | None listed | C105-238P | C1-271P1Z | C104-79P, pad C35-44 |
| P6R6E-206L | 1 | 115/230 V | None listed | C105-238PBZ | C1-271P1Z | C104-79P, pad C35-44 |
| P6RA6F-206L | 1.5 | 115/230 V | None listed | C105-238PBZ | C1-271P1Z | C104-79P, pad C35-44 |
| P6E6F-207L | 1.5 | 230 V | None listed | C105-238PDBAZ | C1-271PZ | C4-78P, pad C35-43 |
| P6EAA6F-216L | 1.75 | 230 V | None listed | C105-238PDCA, printed C105238PDCA | C1-271PZ | C4-78P, pad C35-43 |
| P6RAA6F-216L | 1.75 | 230 V | None listed | C105-238PDCA | C1-271PZ | C4-78P, pad C35-43 |
| P6RA6G-207L | 2 | 230 V | None listed | C105-238PDBAZ | C1-271PZ | C104-79P, pad C35-44 |
| P6E6H-209L | 3 | 230 V | None listed | C105-238PLA | C1-271PZ | C104-79P, pad C35-44 |
| 345076 | 1 | 3-phase TEFC | 354806S | C105-238PBAZ; screw 37337-6081Z | C1-271P1Z | C104-79P, pad C35-44 |
| 345079 | 3 | 3-phase TEFC | 354812S | C105-238PLA; screw 37337-6081Z | C1-271PZ | C104-79P, pad C35-44 |
| P6R62E3-187 | 1 | 3-phase 200/400 V | AP100EH2 | C105-238PBA; screw 37337-6080 | C1-271P1Z | C4-78P, pad C35-43 |
| P6R62F3-188 | 1.5 | 3-phase 200/400 V | None listed | C105-238PDBAZ; screw 37337-6081Z | C1-271PZ | C4-78P, pad C35-43 |
| P6EA6D36-204 | 0.75 | 3-phase 575 V | 16502-0024S | C105-238PX; screw 37337-6081Z | C1-271P1Z | C104-79P, pad C35-44 |
Note on P6EA6D36-204: The catalog prints a stray A after this impeller number; the 2019 parts sheet has none. | ||||||
| P6EA6E36-205 | 1 | 3-phase 575 V | None listed | C105-238P; screw 37337-6081Z | C1-271P1Z | C104-79P, pad C35-44 |
Note on P6EA6E36-205: The catalog prints a stray A after this impeller number; the 2019 parts sheet has none. | ||||||
| P6EA6F36-206 | 1.5 | 3-phase 575 V | 62001-1019S | C105-238PBA; screw 37337-6081Z | C1-271P1Z | C4-78P, pad C35-43 |
Pentair Sta-Rite Max-E-Pro parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The same seal on the 348185 and on every older model. The manual's warning is blunt: run the pump dry and the seal is damaged and the pump starts leaking, and the seal must be replaced. Its seal job is a power-off, drain, pull-the-motor repair: hold the shaft with a 1/4-inch hex key at the back of the motor, unscrew the impeller, tap the old ceramic half out of the seal plate, and press the new one in square. $41.75 US list.
The catalog's rebuild kit: the seal plate o-ring, the shaft seal, the impeller screw o-ring, the diffuser o-ring, two base washers and the trap o-ring. At $48.11 US list it costs $6.36 more than the shaft seal alone, so if the pump is coming apart for the seal, it's the one to order. The catalog lists it on the older models' page.
The o-ring under the strainer lid, on every model. Clean and inspect it each time the lid comes off, and refit it in its groove. Don't lubricate the original: the manual says it carries a permanent internal lubricant. A replacement that doesn't may need a silicone lubricant. Tighten the lid by hand only. $29.77 US list.
The clear Quick-lock lid with its ring and o-ring. It comes off with a counterclockwise turn; the manual says to tap the handles with a rubber mallet if it sticks, and its lugs take a pry bar. Never open the pot on a pump that has failed to prime or run dry: the manual warns of trapped vapor and scalding water, so open the valves and wait until the pot is cool. $112.32 US list.
The clamp that holds the motor and seal plate to the pump body, tightened by its knob, WC36-22Z at $20.34. The manual says the knob can sit anywhere around the pump, but if it's moved after assembly, tighten it while tapping around the clamp so it seals. Never move the clamp with the pump full of water. The seal under it is the seal plate o-ring: 357099Z square or U9-228AZ round on the older models, and gasket 357099 on the 348185. $167.19 US list for the clamp.
Cleaning it is the only routine maintenance the manual lists. Put it back with its large opening toward the pipe port, between the ribs; the manual says the lid won't fit with the basket turned the wrong way. $22.05 US list on the older models' page; the 348185 page prices its basket on request.
If you are doing the job anyway
The seal job opens the seal plate and the diffuser, so every o-ring behind them is in your hand at once.
Shaft seal job
The Quick Kit carries the seal with the o-rings the job disturbs, for $6.36 more than the seal alone.
- Max-E-Pro and IntelliPro Quick Kit356196
Strainer lid that won't seal
The trap o-ring is the usual suspect; a cracked lid is the whole cover assembly, which comes with a new o-ring.
- Trap o-ring, the strainer lid seal35505-1440Z
- Trap cover assembly, the strainer lid17307-0111S
Pentair Sta-Rite Max-E-Pro manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Max-E-Pro installation and user's guide, the 348185 (P/N 356990 Rev. C, 2023)manual
- Max-E-Pro product page: marked discontinued, with every model's electrical figuresspec
- SuperMax and Max-E-Pro single-speed pumps brochure, the DOE models (P1-253, 2021)spec
- Pentair Pool 2025-2026 product catalog, pump parts: the Max-E-Pro on pages 456 to 458, with US list pricesdiagram
- Max-E-Pro series replacement parts, the older catalog pages with every model (PDF 2019)diagram
- Pentair Pool 2025-2026 product catalog, pumps: the riser base kits that line an IntelliFlo3 VSF up with a Max-E-Prospec
- Pentair pool and spa equipment warranty informationspec
Pentair Sta-Rite Max-E-Pro warranty
One year, or two if Pentair counts it as a TEFC Super Duty pump
Pentair's warranty table gives single-speed pumps one year, and single-phase TEFC Super Duty pumps two; it doesn't say which row a TEFC Max-E-Pro falls in. Either way it's parts and labor only when the pump was bought from a store, builder or service company and professionally installed. Bought online, or installed by an owner, it's one year, parts only. Pump mechanical seals and o-rings are consumables, covered for one year. The manual adds that letting the pump freeze voids the warranty.
Manufacturer’s termsPentair Sta-Rite Max-E-Pro complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
59 parts
| No. | Part | Description | Note |
|---|---|---|---|
| — / 1 | 356362S | Motor, 348185 | $695.57 US list. Older models: see the model table |
| 1 / — | 354822S | Motor, 348150 | 1 HP single-phase TEFC. No list price in the catalog |
| 1 / — | 354824S | Motor, 348151 | 1½ HP single-phase TEFC. No list price in the catalog |
| 1 / — | 354818S | Motor, 348153 | 3 HP single-phase TEFC. No list price in the catalog |
| 1 / — | 354806S | Motor, 345076 | 1 HP three-phase TEFC. No list price in the catalog |
| 1 / — | 354812S | Motor, 345079 | 3 HP three-phase TEFC. No list price in the catalog |
| 1 / — | AP100EH2 | Motor, P6R62E3-187 | 1 HP three-phase, 200/400 V. No list price in the catalog |
| 1 / — | 16502-0024S | Motor, P6EA6D36-204 | 3/4 HP, 575 V. No list price in the catalog |
| 1 / — | 62001-1019S | Motor, P6EA6F36-206 | 1½ HP, 575 V. No list price in the catalog |
| 10 / — | C105-238P | Impeller | P6E6D-205L, P6R6D-205L, P6RA6E-205L and P6EA6E36-205 |
| 10 / — | C105-238PBZ | Impeller | 348150, P6E6E-206L, P6R6E-206L and P6RA6F-206L |
| 10 / — | C105-238PBA | Impeller | P6R62E3-187 and P6EA6F36-206 |
| 10 / — | C105-238PBAZ | Impeller | 345076 |
| 10 / — | C105-238PDBAZ | Impeller | 348151, P6E6F-207L, P6RA6G-207L and P6R62F3-188 |
| 10 / — | C105-238PDCA | Impeller | P6EAA6F-216L and P6RAA6F-216L |
| 10 / — | C105-238PLA | Impeller | 348153, P6E6H-209L and 345079 |
| 10 / — | C105-238PX | Impeller | P6EA6D36-204 |
| 11 / — | C1-271P1Z | Diffuser | The 3/4 HP and 1 HP models, P6RA6F-206L and P6EA6F36-206 |
| 11 / — | C1-271PZ | Diffuser | The 1½ HP and larger models, except P6RA6F-206L and P6EA6F36-206 |
| 5 / 2 | C203-194P | Seal plate kit | Every model. Includes the seal plate's o-ring or gasket and the shaft seal. $267.62 US list |
| 2 / — | U30-692SS | Screw, #10-32 by 1/2 in. | Older models. $3.40 US list |
| 2A / — | U43-22SS | Lock washer | The 2019 parts sheet only |
| — / 3 | 357099 | Gasket, seal plate to housing, 348185 | Price on request |
| 3 / — | U17-568 | Bonding lug | Older models. Price on request |
| 4 / — | 17351-0009 | Water slinger | Older models. $3.01 US list |
| 6 / — | U9-228AZ | O-ring, round, seal plate to housing | Older models. $15.63 US list |
| 6 / — | 357099Z | O-ring, square, seal plate to housing | Older models. The 2019 parts sheet prints 375099Z. $16.40 US list |
| 7 / 4 | 17351-0101S | Shaft seal, EPDM black what goes wrong | Every model. $41.75 US list |
| — / 7 | C105-238PDOEZ | Impeller, 348185 | The 2023 manual; the 2025-2026 catalog's 348185 page has no impeller row. Older models: see the model table |
| 8 / 6 | WC36-22Z | Band clamp knob | Every model. $20.34 US list |
| — / 8 | 356359Z | Diffuser, 348185 | $112.80 US list. Older models: see the model table |
| 9 / 5 | C19-37AZ | Band clamp what goes wrong | Every model. $167.19 US list |
| 12 / 9 | 357098Z | Diffuser o-ring, blue coating | The 348185's, per the 2023 manual; the 2019 sheet lists it for the older models too |
| — / 10 | 357841Z | Diffuser screw kit, 348185 | The 2023 manual |
| 10A / — | 35505-1426 | Impeller screw o-ring | Older models. In the Quick Kit |
| 10B / — | 37337-6080 | Impeller screw | P6R62E3-187, per the 2025-2026 catalog |
| 10B / — | 37337-6081Z | Impeller screw | The three-phase and 575 V models, per the 2025-2026 catalog |
| 15 / 11 | 17307-0110S | Trap body assembly | Every model. Trap body, basket, drain plugs and the trap cover assembly. $496.67 US list |
| 12 / — | U9-374Z | Diffuser o-ring | Older models. $8.68 US list |
| 16 / 12 | 17307-0111S | Trap cover assembly what goes wrong | Every model. Trap cover, trap ring and trap o-ring. $112.32 US list |
| 13 / — | U43-21SSZ | Lock washer, #8 | Older models. $2.91 US list |
| 17 / 13 | 35505-1440Z | Trap o-ring what goes wrong | Every model. $29.77 US list |
| 14 / — | U30-542SSZ | Screw, with the C1-271P1Z diffuser | Older models. $3.61 US list |
| 18 / 14 | C8-58PZ | Strainer basket what goes wrong | $22.05 US list on the older models' page; price on request on the 348185's |
| 19 / 15 | U178-920PZ | Drain plug, 1/4 in. NPT | Two on the 348185. $8.07 US list |
| 19 / — | U9-359Z | Drain plug o-ring | Older models. $2.89 US list |
| 21 / 16 | U30-918SS | Base screw | Two required. $7.88 US list |
| — / 17 | C4-79P | Base, 348185 | The 2023 manual |
| 23 / 18 | C35-43 | Motor pad | The 348185, and the older models on base C4-78P |
| 24 / 19 | U30-74SSZ | Screw, 3/8-16 by 1 in. hex head | Four on the 348185. $7.00 US list |
| 20 / — | U43-41SSZ | Base washer | Older models. $4.07 US list |
| 22 / — | C4-78P | Base | Older models marked note 5 in the catalog. $72.55 US list |
| 22 / — | C104-79P | Base with motor pad C35-44 | Older models marked note 6 in the catalog; the 2019 sheet says 3 HP only. $74.26 US list |
| 23 / — | C35-44 | Motor pad, with base C104-79P | The 2019 sheet says 3 HP only |
| — | 357810 | Fan guard kit, 348185 | Price on request |
| — | 357924Z | Fan guard kit, TEFC and Super-Duty | Older models. Price on request |
| — | 356196 | Max-E-Pro and IntelliPro Quick Kit what goes wrong | O-rings, shaft seal, impeller screw o-ring, base washers and trap o-ring. $48.11 US list |
| — | PKG 188 | Union kit, 2 in. slip, a pair | Union collars U11-200P, o-rings U9-362 and slip adapters U11-196P. The 2025-2026 catalog prints PKG 188Z |
| — | PKG 189 | Union kit, 2 in. NPT, a pair | Union collars U11-200P, o-rings U9-362 and NPT adapters U11-199P |