Pentair · Kreepy Krauly
Pentair Kreepy Krauly Legend
Pentair's discontinued original Legend, the booster-pump pressure cleaner: the 28 to 32 RPM wheel test, the back-up valve, hose sizing and the parts.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Kreepy Krauly Legend is the original Legend, the pressure-side cleaner that runs on a booster pump. It came in two colors, the gray-and-white LL505G and the all-gray LL505GG, and Pentair's page now marks both discontinued. The Legend II, whose brochure compares it to the original Legend, runs on the filter pump alone; the Legend needs a booster pump of its own.
The two share many parts, including the top and bottom covers, the turbine shaft and bearings, the sweep hose, the bags, the wheels and the wall fitting screen, but not the wall fitting, back-up valve, feed mast, main frame or hoses. Check which one you have before ordering. Pentair's other pressure-side cleaners here are the Kreepy Krauly Platinum and the discontinued Racer and Racer LS, all on boosters.
What it does
The manual says it travels randomly around the pool, vacuuming and sweeping the floor, and climbs better in pools without sharp angles where the floor meets the wall. About every 3-1/2 minutes, the back-up valve pulls it backward for about 30 seconds to unstick it and mix up its route. The sweep hose trails behind, stirring debris out of corners. Pentair's page credits it with a large intake throat for big and small debris, and four wheels so it doesn't tip.
It wasn't designed for steps, swimouts or use under a solar cover, or for plaster dust and the first cleanup of a new or newly opened pool. If the pool has a chlorinator, solar heating or any equipment that adds air, the manual says to call Pentair's technical support before installing it. Pentair recommends a check every year.
The booster pump
The manual expects a 3/4 HP booster on a dedicated line with a 1-1/2 in. female thread; it calls Pentair's the Universal Booster Pump. The booster isn't self-priming, and it has to be fed from the pool filter ahead of any in-line chlorinator. If the pool has no dedicated cleaner line, the manual says to call Pentair's technical support.
Fitting it
- Flush the cleaner line with the filter pump and booster running, then turn both off.
- Screw the wall adapter by hand into the dedicated line. Twist-lock the wall fitting into it a quarter turn and pull it out to a snug fit.
- Lay the hose out straight in the sun, for a day if you can, to take the coil out of it. If it still goes round in a circle, reverse the first or second section from the wall, or both.
- Cut the soft hose to the pool's depth. The back-up valve sits in the soft hose, 30 in. from the cleaner, and should stay there, so cut any excess from the end that joins the white hose. Leave the first float next to the back-up valve and put the second midway between it and the swivel. If the pool is deeper than 10 ft., don't cut it.
- Size the white hoses. With the hose on the wall fitting, walk the soft hose's end to the farthest point of the pool without stretching it, and measure how far the hose overshoots. Cut half of that from each 10 ft. white hose, next to the marked swivel. If more than 2 ft. comes off each, take off the floats next to that swivel. Keep as many floats as you can, evenly spaced, so the hose floats.
- Put the mender nuts on the swivels first, push the hoses over the barbs and turn the nuts clockwise by hand until tight. Fit the soft hose half an inch over the cleaner's mast with its own mender nut.
- Twist-lock the sand and silt bag onto the cleaner over the rubber debris valve, then lower the cleaner into the pool.
To start it, turn on the filter pump first, wait 30 seconds to push the air out of the hose, then turn on the booster. From then on, the booster's time clock turns it on and off. A large pool can take a third white hose; see the bundle below.
The wheel test
The Legend should turn 28 to 32 RPM. With the pumps off, take the cleaner out and mark a front drive wheel, or use the Pentair logo on the tire's side. Have someone start the pool pump and booster while you hold it just under the water, and count the wheel's turns for exactly one minute, while the back-up valve isn't cycling. Hold the sweep hose, or it will soak you.
- Over 32: unscrew the pressure relief valve at the wall fitting slowly until the count falls between 28 and 32.
- Under 28: the manual says to call a pool professional or Pentair's technical support.
The cleaner-not-moving guide has the same test for other cleaners.
Tuning it
Thrust jet: the jet at the back alters the cleaner's direction. It comes set in the middle, pointing straight out; loosen its two screws to reposition it.
Sweep hose: the screw on the feed mast below the ballast float sets how hard it sweeps. Clockwise for less, counterclockwise for more. If the hose still breaks the surface and sprays, the optional weight, EH09C, goes on its end.
Running it
- Disconnect it before cleaning or backwashing the filter, then run the filter at least five minutes to flush the return lines before reconnecting it. After any filter work, take the wall fitting out and flush the dedicated line.
- Take it out before anyone swims, and before shocking the pool. The manual's rule: water unsafe for swimming is unsafe for the cleaner.
- Empty the bag at half full. Push the U-shaped snap lock up with your thumb to open it, empty the bag, then push the middle of the bag in, stack the edges like an accordion and snap the lock back down. After a storm, run two shorter cycles and empty the bag between them.
- For very fine sand and silt, Pentair's disposable bag replaces the regular one on Legend cleaners. Take the debris valve off and hold the bag on the vacuum tube with a double-wrapped rubber band; throw it away when it's full.
- Store it out of direct sun. For winter, drain all the water out and take the wall fitting out. Freeze damage isn't covered.
When it misbehaves
The manual's troubleshooting, in short:
- Doesn't move, moves sluggishly or hangs on the steps: check both pumps, clean the pool filter and the wall fitting screen, check the wheel speed, check the back-up valve cycles, and look for leaks at the hose connections and swivels. Turn the front wheels backward by hand to free debris from their gear teeth.
- Falls over: usually a full bag. If not, check the ballast float for water inside.
- Won't back up: check the back-up valve cycles out of the water, the wheel speed, and the bag, emptying it if it's even half full.
- Won't climb: brush the walls even without visible algae, check the wheel speed, and reposition the thrust jet.
- Hoses tangle: shorten the hose if it's long, check it floats with the floats evenly spaced, replace any swivel that won't spin, and lay the hose straight in full sun.
- Booster pump very noisy: check the wall fitting is mounted correctly and the filtration system works, then call a pool professional about the booster.
Parts the manual doesn't explain
The 2016 sheet's accessories add a pressure stick without gauge (JVP8), a pressure gauge (15060-0000T) and a step deflector (EU13). The manual never mentions them, and the 2025-2026 catalog doesn't list them.
Where Pentair's documents disagree
- Cleaning time. Pentair's page and the 2020 brochure say most pools in 1 to 3 hours. The manual's general section says about 4 to 6.
- The hose numbers. The manual's US column puts G-L- in front of most part numbers, as G-L-EC86; the 2016 sheet and the catalog don't. The white 10 ft. hose is LD45 on the sheet and in the catalog, but LLD45 in the manual's international column and its own steps for adding a hose. The soft hose is LD50 on the sheet and LLD50 in the manual's international column.
- How many swivels and mender nuts. The manual's box list says four swivels and twelve mender nuts; its parts list gives two swivels and eight mender nuts.
- The gray thrust jet repair kit, 360014. Both the manual and the 2016 sheet say it holds LLC135 and E19. Neither lists either number anywhere else; the gray plate is LLC135G and the thrust jet O-ring is E18.
- The warranty. No document gives a term, and Pentair's warranty table doesn't list the Legend.
Which model do you have?
The model number is on the cleaner label. Everything else in the range is shared — these are the parts that change with it.
| Model | Colors | Bottom cover | Back-up valve |
|---|---|---|---|
| LL505G | Gray and white | 360004 | E10 |
Note on LL505G: Gray top, white bottom, which Pentair suggests for lighter-colored pools. A 22 lb carton. | |||
| LL505GG | All gray | 360011 | LL10PM |
Note on LL505GG: All gray, for darker pools. Where Pentair's lists give a part in two colors, the gray one matches this version. | |||
Pentair Kreepy Krauly Legend parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
A filter screen inside the wall fitting that keeps whatever gets past the pool filter out of the cleaner. It's second on the manual's list for a cleaner that won't move, after the pumps: pull it out of the wall fitting, rinse it and push it back. Never run without it; the manual says that can damage the cleaner and voids the warranty. A screen that keeps plugging means a problem in the pool's filter system. $16.40 US list.
The valve in the soft hose that pulls the cleaner away from where it is, about every 3-1/2 minutes. The manual's test: hold it out of the water, and its jet should come on for about 30 seconds and shut off for about 3-1/2 minutes. If it cycles, check the wheel speed and empty the bag before blaming it. Its gears are EG15. $161.37 US list; the gray one is LL10PM at $166.01.
The twist-lock fitting the hose connects to, with a relief valve that lets off excess pressure. Above 32 RPM, the manual says to unscrew the relief valve slowly until the count falls between 28 and 32. For a noisy booster, its first check is that the wall fitting is mounted correctly. The relief valve alone is E25, at $23.58. $60.18 US list; the gray fitting is LLW22PM at $83.20.
A full bag is the usual reason the cleaner tips over, the manual says. If it isn't the bag, check the ballast float on the mast for a leak: unscrew it by pulling back while turning it counterclockwise, then shake it and listen for water inside. $9.82 US list; the gray float is LLA20G at $14.27.
Rotate or replace the tires when they're worn to the wear groove; the manual calls tires and wheel bearings wear items. A good bearing, EC60 at $32.60, spins freely. Debris jammed in the gear teeth of a front drive wheel can stop the cleaner: rotate the front wheels backward by hand to free it. $21.19 US list; the gray tire is 360012 at $21.17.
An accessory in the manual, designed to climb in problem areas and on fiberglass, tile and smooth surfaces. For a cleaner that won't climb, the manual's first steps are to brush the walls even if they show no algae, check the wheel speed, and reposition the thrust jet by loosening its two screws. Not priced in the 2025-2026 catalog.
Both have the same first fix: the adjustment screw, 370198, on the feed mast below the ballast float. Turn it clockwise for less motion, counterclockwise for more, until the hose sweeps gently. If it still breaks the surface, add the optional sweep hose weight, EH09C at $76.03. The wear rings, EB10, protect the hose; rotate them to avoid flat spots. $58.76 US list; the gray hose is LLB5G at $86.73.
The rubber valve under the debris bag that works like a check valve, letting debris in one way and keeping it in the bag. The manual says to replace it when it starts to stiffen. $6.11 US list.
The manual's fixes for tangling: check the hose isn't too long, that it floats with its floats evenly spaced, and that every swivel spins freely; replace any that won't. Lay the hose straight in full sun to take out its memory. $25.12 US list; the gray swivel is LLD05PM at $36.65.
The bag it ships with, for general use. Empty it at half full; the manual says the cleaner runs better and it's easier emptied dry. It isn't for leaves and twigs, whose sharp points tear it: the coarse mesh leaf bag, EU15 at $83.53, is. Take the cleaner out before adding chemicals to make bags last. $84.73 US list; the gray bag is 360009 at $84.74.
If you are doing the job anyway
Prices are the 2025-2026 catalog's for the Legend, pages 310 and 311; the rest are from the 2021 manual and the 2016 sheet, unpriced.
Longer feed hose, white
The manual's parts for a pool the hose won't reach: one more 10 ft. white hose, four floats, one swivel and two mender nuts, fitted between the soft hose and the white hoses, with any overage cut in thirds from the three white hoses so they stay the same length. The gray equivalents are LLD45PM, LLD10PM, LLD05PM and LLD15PM.
- LD45LD45
- ED10PED10P
- Feed hose swivelED05
- ED15ED15
Pentair Kreepy Krauly Legend manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Legend installation and user's guide (P/N 370270 Rev. E, 10/19/21), English, French, Spanish and Italian, with the parts list on pages 19 and 20manual
- Kreepy Krauly Legend product page, with the discontinued noticespec
- Pentair Pool 2025-2026 product catalog: Legend replacement parts and US list prices on pages 310 and 311diagram
- LL505G and LL505GG replacement parts, the older catalog pages (PDF 2016)diagram
- Kreepy Krauly Legend brochure (P1-801, March 2020)spec
- Cleaning the sand and silt bag, 360002 and 360009guide
- Disposable sand and silt bag installation instructions, for Legend and Polaris cleaners (P/N 370257 Rev. A, 8/11/06)guide
- Pentair pool product warranty informationspec
Pentair Kreepy Krauly Legend warranty
No term in its documents, and Pentair's current warranty table doesn't list it
The manual describes a limited warranty against defects in parts and construction without giving its length, and the 2020 brochure gives none. Pentair's warranty table doesn't list the Legend; it gives the pressure-side Platinum one year and its other cleaners two. The manual calls the tires, wheel bearings, sweep hose and other moving parts wear items, outside the warranty, and says running without the wall fitting screen voids it. Freeze damage isn't covered.
Manufacturer’s termsPentair Kreepy Krauly Legend complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
90 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 360003 | Top cover | $145.34 US list |
| 2 | LLU145N | Main frame | $2,175.35 US list |
| 2 | 360010 | Main frame, gray | |
| 3 | 360004 | Bottom cover | |
| 3 | 360011 | Bottom cover, gray | |
| 4 | LLU6 | Feed mast with O-ring, white | $77.23 US list |
| 4 | LLU6G | Feed mast with O-ring, gray | $93.87 US list |
| 5 | EC86 | Turbine drive shaft, complete | $60.33 US list |
| 6 | EC83 | Turbine spacers | Two |
| 7 | EC80 | Turbine bearings | Two. $59.05 US list |
| 8 | EA40 | Turbine shaft shield | |
| 9 | EC110 | Turbine cover with elbows | $22.04 US list |
| 10 | EC120 | Turbine and venturi hose, 7-3/4 in. | Two |
| 10 | LLC120G | Turbine and venturi hose, 7-3/4 in., gray | Two |
| 11 | EB5L | Sweep hose, complete what goes wrong | $58.76 US list |
| 11 | LLB5G | Sweep hose, complete, gray | $86.73 US list |
| 12 | EB10 | Sweep hose wear ring | Nine |
| 13 | EB25 | Sweep hose jet with collar | |
| 13 | LLB25PM | Sweep hose jet with collar, gray | |
| 14 | 370198 | Sweep hose adjustment screw | |
| 15 | EA20 | Ballast float what goes wrong | $9.82 US list |
| 15 | LLA20G | Ballast float, gray | $14.27 US list |
| 16 | EH07 | Sweep hose sleeve | Four |
| 16 | LLH07PM | Sweep hose sleeve, gray | Four |
| 17 | EU15 | Coarse mesh leaf bag, blue, optional | $83.53 US list |
| 17 | EU15G | Coarse mesh leaf bag, gray collar, optional | $84.93 US list |
| 18 | 360002 | Fine mesh bag, mechanical lock what goes wrong | $84.73 US list |
| 18 | 360009 | Fine mesh bag, mechanical lock, gray | $84.74 US list |
| 18 | EU16 | Fine mesh bag, hook-and-loop fastener | $65.55 US list |
| 18 | EU16G | Fine mesh bag, hook-and-loop fastener, gray | $74.58 US list |
| 19 | EU9 | Debris valve what goes wrong | $6.11 US list |
| 20 | EU7 | O-ring for feed mast | |
| 21 | E18 | O-ring for thrust jet | |
| 22 | EC130 | Thrust jet | |
| 23 | EC135 | Thrust jet plate | |
| 23 | LLC135G | Thrust jet plate, gray | $18.81 US list |
| 24 | EC65 | Axle, large wheels | Four. $8.29 US list |
| 25 | EC70 | Axle plate | Four |
| 26 | 370258Z | Axle screw with lock washer | Eight |
| 27 | 360006 | Wheel without bearings | Four. $25.71 US list |
| 28 | EC60 | Wheel bearings only | Eight. $32.60 US list |
| 29 | EC55 | Wheel screw, plastic | Four. $16.51 US list |
| 29 | LLC55PM | Wheel screw, plastic, gray | Four. $17.91 US list |
| 30 | E10 | Back-up valve what goes wrong | $161.37 US list |
| 30 | LL10PM | Back-up valve, gray | $166.01 US list |
| 31 | 360007 | Wheel with rubber tire what goes wrong | Four. $21.19 US list |
| 31 | 360012 | Wheel with gray tire | Four. $21.17 US list |
| 32 | EB15 | Hose clamp | Five. $4.65 US list |
| 33 | EC40 | Screw | Seven |
| 34 | 360005 | Hub cap | Four. $7.57 US list |
| 34 | 360013 | Hub cap, gray | Four |
| 35 | LD50 | Feed hose, soft, 10 ft. | The 2016 sheet's number; LLD50 in the manual's international column |
| 35 | LLD50PM | Feed hose, soft, gray, 10 ft. | $87.10 US list |
| 36 | ED10P | Feed hose float | Ten. $11.44 US list |
| 36 | LLD10PM | Feed hose float, gray | Ten. $40.97 US list |
| 37 | LD45 | Feed hose, white, 10 ft. | Two. $50.85 US list; LLD45 in the manual's international column and its extra-hose steps |
| 37 | LLD45PM | Feed hose, gray, 10 ft. | Two. $111.74 US list |
| 38 | ED05 | Feed hose swivel what goes wrong | Two. $25.12 US list |
| 38 | LLD05PM | Feed hose swivel, gray | Two. $36.65 US list |
| 39 | LLU1 | Adapter hose, white, 8-1/2 in. | |
| 39 | LLU1PM | Adapter hose, gray, 8-1/2 in. | |
| 40 | ED15 | Feed hose mender nut, plastic | Eight. $13.12 US list |
| 40 | LLD15PM | Feed hose mender nut, plastic, gray | Eight. $23.39 US list |
| 41 | EW22 | Wall fitting, complete what goes wrong | $60.18 US list |
| 41 | LLW22PM | Wall fitting, complete, gray | $83.20 US list |
| 41 | E25 | Pressure relief valve, white | $23.58 US list |
| 41 | LL25PM | Pressure relief valve, gray | |
| 42 | E24 | Wall fitting screen what goes wrong | $16.40 US list |
| 43 | E23 | Quick disconnect adapter | $7.92 US list |
| 43 | LL23PM | Quick disconnect adapter, gray | $15.72 US list |
| 44 | EC64 | Wheel washer, plastic | Four |
| — | EH09C | Sweep hose weight, optional | $76.03 US list |
| 46 | EG15 | Gears for the back-up valve | |
| 47 | EC131 | Thrust jet repair kit: EC130, EC135 and E18 | |
| 47 | 360014 | Thrust jet repair kit, gray | Both lists say it includes EC130, LLC135 and E19 |
| 48 | EA30 | Screw for the shaft shield and turbine cover | Five |
| 49 | 370017 | Sweep hose scrubber | $5.13 US list |
| 50 | EU147 | Snap-fit vacuum tube posts | Two. $9.77 US list |
| 50 | LLU147G | Snap-fit vacuum tube posts, gray | Two. $10.53 US list |
| 51 | EU79 | Nut and bolt, feed mast to vacuum tube | |
| 52 | LLU8 | Venturi jets | Two |
| 52 | LLU8G | Venturi jets, gray | Two |
| 53 | EU80 | Screw, top and bottom cover | Four |
| 54 | 360008 | Hose clip for bag 360002 | |
| 54 | 360015 | Hose clip, gray, for bag 360009 | |
| — | LL209 | Legend hose kit | $538.41 US list |
| — | LC6LSA | Suction cup tires, optional what goes wrong | The manual's accessories page |
| — | JVP8 | Pressure stick without gauge | The 2016 sheet only |
| — | 15060-0000T | Pressure gauge | The 2016 sheet only |
| — | EU13 | Step deflector | The 2016 sheet only |