Pentair · Racer
Pentair Racer
Pentair's discontinued booster-pump pressure cleaner with Night Cruize lights: the flow gauge, the 31 to 36 RPM wheel test, hose sizing and the parts.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Racer is Pentair's pressure-side cleaner with lights. It runs off a dedicated return line on a booster pump, carries its own debris bag, and has twin Night Cruize LEDs powered by its own water turbine. Pentair's item number is 360228, and its page now marks the Racer discontinued.
Pentair made a separate Racer LS too, without the lights and with its own parts pages in the catalog. This page is the Racer only. Pentair's other pressure-side cleaners in this catalog are the Kreepy Krauly Platinum, which also needs a booster, and the discontinued Kreepy Krauly Legend II, which doesn't.
What it does
The manual says it travels in a random pattern, vacuuming and scrubbing, with a rotating brush across the front. It goes into reverse every couple of minutes, which the manual says helps it clean the whole pool, and it climbs better where the floor curves gently into the wall. Its brochure credits it with four venturis and a vacuum intake 40% larger than other pressure-side cleaners.
It wasn't designed for steps, swimouts or use under a solar cover, or for plaster dust and the first cleanup of a new or newly opened pool. If the pool has a chlorinator, solar heating, an ozone generator or any equipment that adds air, the manual says to call Pentair's technical support before installing it.
Fitting it
- Flush the cleaner line with the filter pump and booster running, then turn both off.
- Screw the wall adapter by hand into the dedicated 1-1/2 in. return until it's snug. Push the wall fitting in over the quick-lock pegs, turn it a quarter turn clockwise, and pull gently to engage the pegs.
- Set the flow. Lock the flow gauge onto the wall fitting and start the filter pump, then the booster. Turn the valve in the wall fitting with a flathead screwdriver until the white plunger lines up with the arrows: clockwise for less flow, counterclockwise for more. Turn the booster off, then the filter pump, and take the gauge off.
- Size the hose. It comes as three 10 ft. sections. Cut the soft light gray lead hose, section 1, to the depth of the deepest part of the pool; leave it whole if the pool is deeper than 10 ft. Then connect the hose and walk the free end to the farthest point of the pool, resting it on the water, and cut half the excess from each of sections 2 and 3. If more than 3 ft. comes off each, take one float off each.
- Push the cut ends all the way onto the swivel barbs and tighten the mender nuts. The hose should reach the pool's edge and end no more than 6 in. beyond it. A large pool can take a fourth section, 360266, joined at the wall fitting end.
- Snap the hose's quick connect onto the cleaner's feed tube and click the bag onto the vacuum tube, with the debris seal in place.
To start it, lower it into the pool, start the filter pump, wait at least 60 seconds for air to clear the hose, then start the booster.
The wheel test
The Racer should turn 31 to 33 RPM with the sweep hose on, and 33 to 36 without it. With the pumps off, take the cleaner out and mark a front wheel. Have someone start the filter pump and booster while you hold the cleaner just under the water, and count the marked wheel's turns for one minute, while it isn't reversing. Hold the sweep hose if it's on: it sprays as the pumps start.
- Too fast: turn the wall fitting valve clockwise until the count falls back into range.
- Too slow: the manual says to call a pool professional or Pentair's technical support. Its troubleshooting table checks the pumps, the filter, the wall fitting screen and the flow gauge first.
The cleaner-not-moving guide has the same test for other cleaners.
Tuning it
Thrust jet: the jet at the back, below the sweep hose regulator, steers it. It comes pointing straight out. Turning it toward 12 o'clock makes it climb more, toward 6 less, and left or right moves the cleaner that way. The manual's alternate setting, for better climbing, is 10 o'clock.
Sweep hose: optional, and the manual says most pools don't need it. Its regulator comes closed. To open it, push the hose fitting onto the regulator and turn it about 45 degrees clockwise, then pull it out to lock. To close it, turn it back. Never adjust it while the cleaner is running.
Running it
- Disconnect it before cleaning or backwashing the filter, then run the filter and booster for at least five minutes to flush the returns before reconnecting it. Clean the wall fitting screen after its first cycle, too.
- Take it out before anyone swims, and before shocking the pool. The manual's rule: water unsafe for swimming is unsafe for the cleaner.
- Empty the bag. To take it off, unhook its strap from the hose, press the release button on the vacuum tube and lift. On the hook-and-loop bag, pull the tabs apart at the top, turn it over and empty it. Strap it back on above the first float so it doesn't fold over. If the pool is very dirty, run two short cycles and empty the bag between them.
- Inspect the wear parts: the wall fitting screen, tires, bag, the sweep hose scrubber and the wear rings on the sweep hose, which should turn freely.
- Store the hose straight, with no kinks. If it was coiled, lay it straight in the sun for 12 to 24 hours before using it, and check the flow with the gauge.
When it misbehaves
The manual's troubleshooting, in short:
- Doesn't move or moves slowly: check both pumps run and move water, clean the pool filter and the wall fitting screen, check the flow with the gauge, and look for leaks at the hose connections and swivels. Turn the front wheels backward by hand to free debris from their gear teeth, and check the rear wheels spin.
- Hangs on the steps or won't reverse: check the front wheels reverse about every 2-1/2 minutes, and check the flow.
- Won't climb: empty the bag, check the flow, and turn the thrust jet up.
- Tilts to one side: usually a full bag. It leans onto two wheels in some turns, so watch it for a few minutes first.
- Hoses tangle: shorten the hose if it's long, space the floats about two feet apart, take out kinks, and replace any swivel that's tight.
- Booster pump very noisy: check both pumps move water and the wall fitting is in properly, with a good O-ring. Then call a pool professional about the booster.
Parts the manual doesn't explain
The sheet's hose drawing puts an in-line filter, 360392, in the feed hose, with its own screen cartridge, 360437. The manual lists both but never mentions them in its text.
The tie bar stop kit guide from 2018 adds two stops to the Racer's tie bar, and to the Racer LS's. Fitting them is a strip-down: all four wheels and the top cover come off, then the chassis lifts out of the lower cover to free the tie bar. The guide doesn't say what the stops are for, and no list gives the kit a part number.
Where Pentair's documents disagree
- Cleaning time. The manual's operation page recommends a one-hour cycle for an average 15 by 30 ft. pool. Its safety page says about 4 to 6 hours.
- The reverse cycle. Its overview says about every two minutes. Its operation page says about every 2-1/2 minutes, for about 15 seconds, and so does its troubleshooting.
- The tune-up kit, 360263. The catalog lists it at $64.05, and at $255.93 in the box beside it that lists what's inside: a bag, a drive shaft, four wheel bearings, two drive shaft bearings, a scrubber bearing, two large tires, a scrubber, two small wheels, two needle bearings, two wheel screws, two 1/2 in. screws and two hubcaps.
- The Racer LS's pages. The catalog prices five of the same part numbers differently there: the 10 ft. hard hose, 360266, at $162.87 rather than $95.77; the wall fitting screen, E24, at $16.40 rather than $27.64; the wall adapter, LL23PM, at $15.72 rather than $53.69; the in-line filter, 360392, at $65.32 rather than $56.13; and the float, 360270, as "call" rather than $101.10. This page uses the Racer's own pages.
- The water management kit, 360261. A footnote on the 2021 sheet and in the catalog says a cleaner made before 15 January 2016 will need it replaced, but nothing on either list carries the footnote's mark, so neither says what job calls for it.
- The manual and the 2021 sheet. The sheet calls item 4 the chassis kit with tie bar and item 24 the feed mast kit; the manual calls them the chassis kit and the feed line connector kit. The manual marks the mechanical-lock bag, 360269, as not shown; the sheet draws it.
- The warranty. No document gives a term, and Pentair's warranty table doesn't list the Racer.
Which model do you have?
The model number is on the cleaner label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Feed hose | Large tires |
|---|---|---|---|
| Racer | 360228 | Three 10 ft. sections | 360237 |
Note on Racer: Pentair's only item number for it, which its page calls the Kreepy Krauly Racer, in a 22.5 lb carton. The page now carries the discontinued notice. The Racer LS is a separate model with its own parts pages. | |||
Pentair Racer parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The stainless steel screen inside the wall fitting, a second filter for whatever gets past the pool filter. It's on the manual's list for a cleaner that won't move: turn off the booster and then the filter pump, pull the wall fitting, rinse the screen and push it back. Never run without it; the manual says that can damage the cleaner and void the warranty. A screen that keeps getting dirty points at the pool's filter system. $27.64 US list.
The quick-lock fitting the hose connects to, with the flow valve you turn with a flathead screwdriver. For a noisy booster, the manual says to check both pumps are moving water, then that the wall fitting is properly installed; if it leaks, an O-ring may need replacing. If the noise goes on, it says to call a pool professional about the booster. $56.54 US list.
The manual's fixes for tangling: check the hose isn't too long, that it floats with its floats about two feet apart, that it has no kinks, and that every swivel spins freely. Replace any swivel that's tight. A hose stored coiled straightens after 12 to 24 hours laid straight in the sun. $80.78 US list.
The brush at the front turns with the front wheels. Watch the running cleaner: the wheels and the brush should turn together. If the brush doesn't, the manual's fix is to clear any tangled debris from it. The scrubber gear kit is 360238. $100.61 US list.
For a dragging rear wheel, the manual says to clear tangled debris from the wheel sleeve, pulling the wheel straight off to get at it. For one that keeps falling off, replace the wheel and its sleeve; no list gives the sleeve its own number. Free-spinning rear wheels are also on its list for a slow cleaner. $101.10 US list.
The manual says the tires protect the pool's floor and give traction, and wear out and need replacing occasionally. Debris jammed in the gear teeth of a front wheel can stop the cleaner: turn the front wheels backward by hand to free it. The large wheel kit is 360235. $74.04 US list.
A cleaner that tilts to one side usually has a full bag, the manual says, though it tips onto two wheels for a moment in some turns. Replace the bag when the fabric is torn. This kit comes without the collar, 360241 at $19.28; the lists also give a bag with a mechanical lock, 360269, unpriced. It's easier to empty dry. $72.90 US list.
The fix is the sweep hose regulator, which comes closed from the factory: make sure it's fully open. Push the hose fitting on and turn it about 45 degrees clockwise. Never adjust it while the cleaner runs. The roller rings that protect the hose, which the lists call wear rings (EB10G), should turn freely. $86.39 US list.
The lights run off a generator turbine, and the manual says dark lights don't affect cleaning. Debris may be clogging the turbine. Pull the left rear wheel straight off, push a large paper clip about 2 in. into the access hole until you feel the paddle, and turn it several times. Not priced in the 2025-2026 catalog.
In some vinyl pools with a deep diving end, the cleaner struggles over the slope into the shallow end. The manual's fix is two wedges pushed between tire and wheel to put a hump in the tires, lined up with each other, or it may still struggle. They came with the cleaner; the lists call the kit the wheel hump insert kit. Not priced in the 2025-2026 catalog.
If you are doing the job anyway
Prices are the 2025-2026 catalog's, which lists 28 Racer parts; the rest are from the 2024 manual and the 2021 sheet, unpriced.
Hook-and-loop bag with a new collar
The bag kit comes without its collar, so a cleaner whose collar is cracked or lost needs both. The other bag on Pentair's lists is the mechanical-lock bag, 360269, unpriced.
- Debris bag, hook-and-loop, without collar360240
- 360241360241
Pentair Racer manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Racer installation and user's guide (P/N 371004 Rev. E, 3/14/24), English, Spanish and French, with the parts list on page 13manual
- Racer product page, with the discontinued noticespec
- Pentair Pool 2025-2026 product catalog: Racer replacement parts and US list prices on pages 304 and 305diagram
- Racer replacement parts sheet (PDF 2021)diagram
- Tie bar stop kit installation guide, Racer and Racer LS (P/N 371209 Rev. A, 10/22/18)guide
- Racer brochure (P1-163, July 2019)spec
- Pentair pool product warranty informationspec
Pentair Racer warranty
No term in its documents, and Pentair's current warranty table doesn't list it
The 2024 manual mentions a warranty card and says running without the wall fitting screen can damage the cleaner and void the warranty, but it gives no term, and neither does the 2019 brochure. Pentair's warranty table doesn't list the Racer. It gives the pressure-side Platinum one year and its other cleaners two.
Manufacturer’s termsPentair Racer complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
51 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 360229 | Top front cover kit | |
| 2 | 360230 | Rear cover kit | $92.79 US list |
| 3 | 360231 | Bottom cover kit | |
| 4 | 360391 | Chassis kit | With the tie bar, per the 2021 sheet |
| 5 | 360233 | Front grill kit | |
| 6 | 360234 | Side covers kit | |
| 7 | 360235 | Large wheel kit | $70.38 US list |
| 8 | 360236 | Small wheel kit what goes wrong | $101.10 US list |
| 9 | 360237 | Large tires kit what goes wrong | $74.04 US list |
| 10 | 360238 | Scrubber gear kit | $21.68 US list |
| 11 | 360239 | Scrubber kit what goes wrong | $100.61 US list |
| 12 | 360240 | Debris bag kit, hook-and-loop, without collar what goes wrong | $72.90 US list |
| 13 | 360241 | Debris bag collar kit | $19.28 US list |
| 14 | 360242 | Vacuum tube kit | $56.13 US list |
| 15 | 360243 | Debris valve kit | |
| 16 | 360244 | Sweep hose kit what goes wrong | $86.39 US list |
| 17 | 360245 | Sweep hose scrubber kit | $21.56 US list |
| 18 | 360246 | Gear box kit | $67.33 US list |
| 19 | 360247 | Timer valve kit | $115.90 US list |
| 20 | 360248 | LED kit what goes wrong | |
| 21 | 360249 | Feed hose swivel kit: one swivel, two mender nuts what goes wrong | $80.78 US list |
| 22 | 360250 | Quick connector to the cleaner: mender nut, swivel and connector | $39.86 US list |
| 23 | 360251 | Wall fitting with two O-rings what goes wrong | $56.54 US list |
| 24 | 360252 | Feed mast kit: feed tube, O-ring and two screws | The 2021 sheet's name; the manual calls it the feed line connector kit |
| 25 | 360253 | Drive shaft kit: drive shaft and two bearings | $36.25 US list |
| 26 | LLC55PMB | Wheel screw kit | |
| 27 | 360255 | Screw kit | Eleven 1/2 in., four 5/8 in., nine machine screws and two 1 in. |
| 28 | 360256 | Turn jet hose kit, right and left | |
| 29 | 360257 | Rear thrust jet hose kit: thrust jet and two 5/8 in. screws | |
| 30 | 360258 | Rubber button kit | |
| 31 | 360414 | Turbine kit | $32.39 US list |
| 32 | 360260 | Venturi manifold kit | |
| 33 | 360261 | Water management kit | $43.57 US list |
| 34 | 360262 | Turbine hose kit | |
| 35 | 360263 | Tune-up kit | $64.05 in the catalog's list, $255.93 in its own box |
| 36 | 360264 | Feed hose kit, complete | $92.79 US list |
| 37 | 360265 | Soft feed hose, 10 ft. | $32.00 US list |
| 38 | 360266 | Hard feed hose, 10 ft. | $95.77 US list |
| 39 | E24 | Wall fitting screen what goes wrong | The lists call it the debris screen. $27.64 US list |
| 40 | LL23PM | Threaded wall adapter | $53.69 US list |
| 41 | EB10G | Sweep hose wear ring | |
| 42 | 360270 | Feed hose float | $101.10 US list |
| 43 | 360268 | Feed hose O-ring kit | One each of -017, -020, -012, -027 and -220, and six -011 |
| 44 | 360269 | Debris bag with mechanical lock | |
| 45 | 360274 | Wheel hump insert kit, the tire wedges what goes wrong | |
| 46 | 360434 | Axle kit | |
| 47 | EC64 | Wheel washer kit | |
| 48 | 360392 | In-line filter kit | $56.13 US list |
| 49 | 360437 | Replacement screen cartridge for the in-line filter | |
| — | 360320 | Quick disconnect hose connector kit | $6.47 US list; $4.77 on the 2021 sheet |
| — | 360318 | Sweep tail quick connect | The 2021 sheet only, at $3.70 |