Pentair · Kreepy Krauly
Pentair Kreepy Krauly Legend II
Pentair's discontinued booster-free pressure cleaner: the 25 to 32 RPM wheel test, the back-up valve check, the wear parts, and where its documents disagree.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Kreepy Krauly Legend II is Pentair's pressure-side cleaner that needs no booster pump. It screws into a dedicated return line and runs on the filter pump's own flow, during the normal filtration cycle. It came in two colors, the gray-and-white LX5000G and the all-gray LX5000GG, and Pentair's page now marks both discontinued.
Most pressure-side cleaners need a booster pump, including Pentair's own Kreepy Krauly Platinum and its discontinued Racer. The Legend II's brochure says it cleans like the original Legend, which runs on a booster, without one.
What it does
The manual says it travels randomly around the pool, vacuuming and sweeping the floor, and climbs better in pools without sharp curves where the floor meets the wall. About every 3-1/2 minutes, the back-up valve pulls it backward for about 30 seconds to unstick it and mix up its route. The sweep hose trails behind, stirring debris out of corners.
It wasn't designed for steps, swimouts or use under a solar cover, or for plaster dust and the first cleanup of a new or newly opened pool.
Fitting it
- Flush the cleaner line with the pump, then turn the pump off.
- Screw the wall adapter by hand into the return. Twist-lock the wall fitting into it a quarter turn.
- Pressure test, with a clean filter: with the pump running, hold the pressure tester end of the hose underwater and cover its large hole. The relief valve in the wall fitting should let water out. If it doesn't, the manual says the pump may not have enough pressure to run the cleaner.
- Size the hose. Lay it in the sun for a day if you can, to take the coil out of it. With the pump on, pull the free end to the farthest corner without stretching it. Excess comes off the first 6 ft. section, the one nearest the wall. The hose lengthens under pressure, so measure twice.
- Take off the pressure tester, whose mender nut has a left-hand thread. Connect the hose to the swivel mast with no twist in it, and twist-lock the bag onto the vacuum tube, with the debris valve in place.
The wheel test
The Legend II should turn 25 to 32 RPM. Mark a front drive wheel, hold the running cleaner just under the surface, and count its turns for exactly one minute, while the back-up valve isn't cycling.
- Under 25: clean the screen inside the wall fitting first, then the skimmer basket, pump basket and filter. If the line has a gate valve, open it further. If it's still slow, the manual says to call a pool professional.
- Over 32, when it flies around the pool: unscrew the relief valve at the wall fitting slowly until the count drops into range, or close down the gate valve.
The cleaner-not-moving guide has the same test for other cleaners.
Tuning it
Thrust jets: two at the back steer it. Pentair sets them slightly to the right. Point them up to climb more, down to climb less, and left or right to push it that way.
Sweep hose: the screw on the swivel mast below the ballast float sets how hard it sweeps. Clockwise for less, counterclockwise for more. Turn it down if the hose gets sucked into the cleaner or sprays out of the water.
Running it
- Disconnect it before cleaning or backwashing the filter, then run the filter at least five minutes to flush the return lines before reconnecting.
- Take it out before anyone swims, and before shocking the pool. The manual's rule: water unsafe for swimming is unsafe for the cleaner.
- Empty the bag at half full. After a storm, run it in two shorter cycles and empty the bag between them.
- For very fine sand and silt, Pentair's disposable bag replaces the regular one on Legend cleaners. Take the debris valve off and hold the bag on the vacuum tube with a double-wrapped rubber band; throw it away when it's full.
- Store it out of direct sun. For winter, drain all the water out and take the wall fitting out. Freeze damage isn't covered.
When it misbehaves
The manual's troubleshooting, in short:
- Doesn't move or moves slowly: check the filter pump, the skimmer basket, the wall fitting screen and the wheel speed. Check the back-up valve cycles, that the hose and swivels don't leak, and that nothing's jammed in a front wheel's gear teeth.
- Won't back up: check the back-up valve cycles out of the water, the wheel speed, and the bag.
- Won't climb: brush the walls even without visible algae, check the wheel speed, and reposition the thrust jets.
- Hoses tangle: shorten the hose if it's long, space the floats evenly, and replace any swivel that won't spin.
Where Pentair's documents disagree
- Cleaning time. The 2022 brochure says most pools in 1 to 3 hours. The 2011 manual's general section says about 4 to 6.
- The short feed hose section. The manual's box list says 4-1/2 ft. Its hose drawing and its cutting tips say 5 ft.
- The gray thrust jet repair kit, 360014. Both the manual and the 2016 sheet say it holds LLC135 and E19. Neither lists either number anywhere else; the gray plate is LLC135G and the thrust jet O-ring is E18.
- What's still priced. The 2025-2026 catalog lists only 11 Legend II parts. The rest, including the wall fitting, back-up valve and bags, appear only in the manual and the 2016 sheet.
- The warranty. No document gives a term, and Pentair's warranty table no longer lists the cleaner.
Which model do you have?
The model number is on the cleaner label. Everything else in the range is shared — these are the parts that change with it.
| Model | Colors | Bottom cover | Tire |
|---|---|---|---|
| LX5000G | Gray and white | 360004 | 360007 |
Note on LX5000G: Gray top, white bottom, which Pentair suggests for lighter-colored pools. | |||
| LX5000GG | All gray | 360011 | 360012 |
Note on LX5000GG: All gray, for darker pools. Where Pentair's lists give a part in two colors, the gray one matches this version. | |||
Pentair Kreepy Krauly Legend II parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
A filter screen inside the wall fitting that catches whatever gets past the pool filter. The manual says a small amount of debris on it significantly affects the cleaner, so it's the first thing on its list for a low wheel count. Pull it out, rinse it and push it back. Never run without it: the manual says that can damage the cleaner and voids the warranty. A screen that keeps plugging means a problem in the pool's filter system.
The valve in the feed hose that pulls the cleaner away from where it is, about every 3-1/2 minutes. The manual's test: hold it out of the water, and its jet should come on for about 30 seconds and shut off for about 3-1/2 minutes. If it cycles, check the wheel speed and empty the bag before blaming it. The gray version is 360018; its gear assembly, LX16, is listed separately.
The twist-lock fitting the feed hose connects to, with a pressure relief valve that lets off excess water. Above 32 RPM, the manual says to unscrew the relief valve slowly until the count falls between 25 and 32, or close down a gate valve on the cleaner line if there is one. The gray version is 360024; the valve assembly alone is LX25.
Rotate or replace the tires when they're worn to the wear groove; the manual calls tires and wheel bearings wear items. A good bearing, EC60, spins freely. Debris jammed in the gear teeth of a front drive wheel can stop the cleaner: rotate the front wheels backward by hand to free it. The gray tire is 360012.
Both have the same fix: the adjustment screw, 370198, on the swivel mast below the ballast float. Turn it clockwise for less motion, counterclockwise for more, until it sweeps gently. The wear rings, EB10, protect the hose; rotate them to avoid flat spots. $58.76 US list; the gray hose is LLB5G at $86.73.
The rubber valve under the debris bag that works like a check valve, keeping debris in when the water stops. The manual says to replace it when it starts to stiffen, and to make sure it's in place before locking the bag on.
The manual's fixes for tangling: check the feed hose isn't too long, that it floats with its floats evenly spaced, and that every swivel spins freely; replace any that won't. A hose that remembers being coiled straightens after a day laid out in the sun. The gray swivel is 360023.
The bag it ships with, for general use. Empty it at half full; the manual says the cleaner runs better and it's easier emptied dry. It isn't for leaves and twigs, whose sharp points tear it: the coarse mesh leaf bag, EU15 at $83.53, is. Take the cleaner out before adding chemicals to make bags last. The gray bag is 360009.
If you are doing the job anyway
Prices are the 2025-2026 catalog's, which lists only 11 Legend II parts; the rest are from the 2011 manual and the 2016 sheet, unpriced.
Longer feed hose, white
The manual's parts for a pool the hose won't reach: one 6 ft. section, one swivel, two menders with O-rings and one float. The gray equivalents are 360020, 360023, 360022 and 360019.
- LX17LX17
- Feed hose swivelLX19
- LX20LX20
- LXD10LXD10
Pentair Kreepy Krauly Legend II manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Legend II installation manual (P/N 370271 Rev. C, 04/04/11), with the parts lists on pages 12 to 15manual
- Kreepy Krauly Legend II product page, with the discontinued noticespec
- Pentair Pool 2025-2026 product catalog: Legend II replacement parts and US list prices on page 312diagram
- LX5000G and LX5000GG replacement parts, the older catalog pages (PDF 2016)diagram
- Kreepy Krauly Legend II brochure (P1-811, May 2022)spec
- Disposable sand and silt bag installation instructions, for Legend and Polaris cleanersguide
- Pentair pool product warranty informationspec
Pentair Kreepy Krauly Legend II warranty
No term in its documents, and Pentair's current warranty table doesn't list it
The manual describes a limited warranty without giving its length, the brochures give none, and Pentair's warranty table no longer lists the Legend II. It does list Pentair's pressure-side Platinum at one year and its other cleaners at two. The manual calls the tires, wheel bearings, sweep hose and other moving parts wear items, outside the warranty, and says running without the wall fitting screen voids it. Freeze damage isn't covered.
Manufacturer’s termsPentair Kreepy Krauly Legend II complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
89 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 360003 | Top cover | $145.34 US list |
| 2 | LXU145N | Main frame | |
| 2 | 360016 | Main frame, gray | |
| 3 | 360004 | Bottom cover | |
| 3 | 360011 | Bottom cover, gray | |
| 4 | LXU6 | Feed mast with O-ring and swivel, gray | $82.98 US list |
| 4 | 360017 | Feed mast with O-ring and swivel | |
| 5 | EC86 | Turbine drive shaft, complete | $60.33 US list |
| 6 | EC83 | Turbine spacers | Two |
| 7 | EC80 | Turbine bearings | Two. $59.05 US list |
| 8 | EA40 | Turbine shaft shield | |
| 9 | LXC110 | Turbine cover with elbows | |
| 10A & B | EC120 | Turbine and venturi hose, 7-3/4 in. | Two and one. $3.13 US list |
| 10A & B | LLC120G | Turbine and venturi hose, 7-3/4 in., gray | |
| 11 | EB5L | Sweep hose, complete what goes wrong | $58.76 US list |
| 11 | LLB5G | Sweep hose, complete, gray | $86.73 US list |
| 12 | EB10 | Sweep hose wear ring | Nine |
| 13 | EB25 | Sweep hose jet with collar | |
| 13 | LLB25PM | Sweep hose jet with collar, gray | |
| 14 | 370198 | Sweep hose adjustment screw | |
| 15 | EA20 | Ballast float | $9.82 US list |
| 15 | LLA20G | Ballast float, gray | $14.27 US list |
| 16 | EH07 | Sweep hose sleeve | Four |
| 16 | LLH07PM | Sweep hose sleeve, gray | Four |
| 17 | EU15 | Coarse mesh leaf bag, blue, optional | $83.53 US list |
| 17 | EU15G | Coarse mesh leaf bag, gray collar, optional | $84.93 US list |
| 18 | 360002 | Fine mesh bag, mechanical lock what goes wrong | |
| 18 | 360009 | Fine mesh bag, mechanical lock, gray | |
| 18 | EU16 | Fine mesh bag, hook-and-loop fastener | |
| 18 | EU16G | Fine mesh bag, hook-and-loop fastener, gray | |
| 19 | EU9 | Debris valve what goes wrong | |
| 20 | EU7 | O-ring for feed mast | |
| 21 | E18 | O-ring for thrust jet | |
| 22 | EC130 | Thrust jet | |
| 23 | EC135 | Thrust jet plate | |
| 23 | LLC135G | Thrust jet plate, gray | |
| 24 | EC65 | Axle, large wheels | Four |
| 25 | EC70 | Axle plate | Four |
| 26 | 370258Z | Axle screw with lock washer | Eight |
| 27 | 360006 | Wheel without bearings | Four |
| 28 | EC60 | Wheel bearings only | Eight |
| 29 | EC55 | Wheel screw, plastic | Four |
| 29 | LLC55PM | Wheel screw, plastic, gray | Four |
| 30 | 360007 | Wheel with rubber tire what goes wrong | Four |
| 30 | 360012 | Wheel with gray tire | Four |
| 31 | 360005 | Hub cap | Four |
| 31 | 360013 | Hub cap, gray | Four |
| 32 | EB15 | Hose clamp | Seven |
| 33 | EC40 | Screw | Seven |
| 34 | EC64 | Wheel plastic washer | Four |
| 35 | EC131 | Thrust jet repair kit: EC130, EC135 and E18 | |
| 35 | 360014 | Thrust jet repair kit, gray | Both lists say it includes EC130, LLC135 and E19 |
| 36 | EA30 | Screw for the shaft shield and turbine cover | Five |
| 37 | EU147 | Snap-fit vacuum tube posts | Two |
| 37 | LLU147G | Snap-fit vacuum tube posts, gray | Two |
| 38 | EU79 | Nut and bolt, feed mast to vacuum tube | |
| 39 | LXU8 | Venturi jets | Two |
| 40 | EU80 | Screw, top and bottom cover | Four |
| 41 | 370017 | Sweep hose scrubber | |
| 42 | 360008 | Hose clip for bag 360002 | The manual |
| 42 | 360015 | Hose clip, gray, for bag 360009 | The manual |
| — | EH09C | Sweep hose weight, optional | |
| H2 | LX10 | Back-up valve, low pressure what goes wrong | |
| H2 | 360018 | Back-up valve, low pressure, gray | |
| H2 | E15 | Back-up valve housing screw | Six |
| Inside H2 | E13 | Back-up valve housing O-ring | |
| Inside H2 | E14 | Back-up valve gear assembly O-ring | |
| Inside H2 | LX16 | Back-up valve gear assembly | |
| H3 | LXD10 | Feed hose float, white | Seven |
| H3 | 360019 | Feed hose float, gray | Seven |
| H4 | LX18 | Feed hose, white, 2 ft. section | |
| H4 | 360021 | Feed hose, gray, 2 ft. section | |
| H5 | LX17 | Feed hose, white, 6 ft. section | Four |
| H5 | 360020 | Feed hose, gray, 6 ft. section | Four |
| H6 | LX20 | Feed hose mender, white, with O-ring | Twelve |
| H6 | 360022 | Feed hose mender, gray, with O-ring | Twelve |
| H7 | LX19 | Feed hose swivel, white what goes wrong | Four |
| H7 | 360023 | Feed hose swivel, gray | Four |
| H8 | LXW22 | Wall fitting, complete, white what goes wrong | |
| H8 | 360024 | Wall fitting, complete, gray | |
| Inside H8 | E23 | Wall fitting adapter, white | |
| Inside H8 | LL23PM | Wall fitting adapter, gray | |
| Inside H8 | E21 | Wall fitting O-ring | Two-pack |
| Inside H8 | E24 | Wall fitting screen what goes wrong | |
| Inside H8 | LX25 | Wall fitting valve assembly, white | |
| Inside H8 | 360025 | Wall fitting valve assembly, gray | |
| H9 | LX26 | Pressure tester | |
| — | LX509 | Feed hose, complete, gray | The 2016 sheet |
| — | LX209 | Feed hose, complete, white | The 2016 sheet |