Pentair · Racer
Pentair Racer LS
Pentair's discontinued Racer LS pressure cleaner: the 35 to 42 RPM wheel test, the back-up valve, the in-line filter, hose sizing and the parts.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Racer LS is the Racer's sibling without the lights. Like the Racer, it runs off a dedicated return line on a booster pump and carries its own debris bag, but it reverses with a back-up valve in its hose rather than a timer valve inside the cleaner, and it turns faster. Pentair's item number is 360330, and its page now marks the Racer LS discontinued.
The two share wheels, tires, the bag, the sweep hose, the wall fitting and the in-line filter, but not the covers or the reversing parts, and Pentair's lists disagree on the chassis, so check which one you have before ordering. Neither the Racer LS's manual nor its parts lists mention Night Cruize lights, and they list no LED kit. Pentair's other pressure-side cleaners here are the Kreepy Krauly Platinum, which also needs a booster, and the discontinued Kreepy Krauly Legend II, which doesn't.
What it does
The manual says it travels in a random pattern, vacuuming and sweeping the floor, and climbs better where the floor curves gently into the wall. About every 3-1/2 minutes the back-up valve in the hose pulls it backward for about 15 seconds, to get it past obstructions and mix up its route. Its brochure credits it with four vacuum jets, 25% more cleaning power than other pressure-side cleaners, and a vacuum intake it calls 40% larger.
It wasn't designed for steps, swimouts or use under a solar cover, or for plaster dust and the first cleanup of a new or newly opened pool. Its 2021 brochure suggests pairing it with Pentair's HydroBoost booster pump.
Fitting it
- Flush the cleaner line with the filter pump and booster running, then turn both off.
- Check the wall adapter. If the one in the return isn't Pentair's, press out its red or blue flow restrictor plate with your thumbs. The manual says a plate left in starves the cleaner, so it runs slowly and takes longer to clean.
- Screw the wall adapter by hand into the dedicated 1-1/2 in. return until it's snug. Push the wall fitting in over the quick-lock pegs, turn it a quarter turn clockwise, and pull gently to engage the pegs.
- Size the hose. It comes as two 10 ft. sections and a lead hose in two pieces, 7.5 ft. and 2.5 ft., with the back-up valve between them. Cut the soft light gray lead hose, section 1, so it reaches the depth of the deepest part of the pool, back-up valve included; leave it whole if the pool is deeper than 10 ft. Then connect the hose and walk the free end to the farthest point of the pool, resting it on the water, and cut half the excess from each of sections 2 and 3. If more than 3 ft. comes off each, take one float off each.
- Push the cut ends all the way onto the swivel barbs and tighten the mender nuts. The hose should reach the pool's edge and end no more than 6 in. beyond it. A large pool can take another 10 ft. section, 360266, joined at the wall fitting end.
- Snap the hose's quick connect onto the cleaner's feed tube and click the bag onto the vacuum tube, with the debris seal in place.
To start it, lower it into the pool, start the filter pump, wait at least 60 seconds for air to clear the hose, then start the booster.
The wheel test
The Racer LS should turn 35 to 42 RPM. With the pumps off, take the cleaner out and mark a front wheel. Have someone start the filter pump and booster while you hold the cleaner just under the water, and count the marked wheel's turns for one minute, while the back-up valve isn't cycling. Hold the sweep hose: it sprays as the pumps start.
- Over 42: turn the wall fitting valve clockwise with a flathead screwdriver until the count drops back under 42.
- Under 35: the manual says to call a pool professional or Pentair's technical support. Its troubleshooting table checks the pumps, the filter, both screens and the restrictor plate first.
The cleaner-not-moving guide has the same test for other cleaners.
The sweep hose
It comes with a cap over the sweep hose connection, which blocks the flow until the hose goes on. To take the cap off, push it in toward the cleaner and turn it a quarter turn counterclockwise, then pull it straight off. Line the lock tabs inside the hose's fitting up with the slots on the connection, push it on, turn it clockwise about a quarter turn until it stops, and pull it back to lock it. To take the hose off, push it in and turn it back.
Running it
- Clean the wall fitting screen once a week, the manual says, and the in-line filter's screen whenever you empty the bag.
- Disconnect it before cleaning or backwashing the filter, then run the filter and booster for at least five minutes to flush the returns before reconnecting it. Clean the wall fitting screen after its first cycle, too.
- Take it out before anyone swims, and before shocking the pool. The manual's rule: water unsafe for swimming is unsafe for the cleaner.
- Empty the bag. Unhook its strap from the hose, press the release button on the vacuum tube and lift. Pull the tabs apart at the top, turn the bag over and empty it, then close the hook-and-loop strip along its whole length. Strap it back on above the first float so it doesn't fold over. If the pool is very dirty, run two short cycles and empty the bag between them.
- Inspect the wear parts: the tires, the bag, the sweep hose scrubber and the wear rings on the sweep hose, which should turn freely.
- Store the hose straight, with no kinks. If it was coiled, lay it straight in the sun for 12 to 24 hours before using it.
When it misbehaves
The manual's troubleshooting, in short:
- Doesn't move or moves slowly: check both pumps run and move water, clean the pool filter, both screens, and check the wheel speed. Look for leaks at the hose connections and swivels, and for a restrictor plate in the wall adapter. Turn the front wheels backward by hand to free debris from their gear teeth, check the rear wheels spin, and check the back-up valve cycles.
- Hangs on the steps or won't reverse: check the back-up valve cycles about every 3-1/2 minutes, then the wheel speed. For one that won't reverse, clean both screens too.
- Won't climb: empty the bag and check the wheel speed.
- Tilts to one side: usually a full bag. It leans onto two wheels in some turns, so watch it for a few minutes first.
- Hoses tangle: shorten the hose if it's long, space the floats about two feet apart, take out kinks, and replace any swivel that's tight.
- Booster pump very noisy: check both pumps move water and the wall fitting is in properly, with a good O-ring. Then call a pool professional about the booster.
- Rear wheels dragging: clear the debris tangled in them.
Parts the manual doesn't explain
The manual's list of what comes in the box includes a flow gauge, but its flow instructions use only the wheel count, and no list gives the gauge a number.
The tie bar stop kit guide from 2018 adds two stops to the Racer LS's tie bar, and to the Racer's. Fitting them is a strip-down: all four wheels and the top cover come off, along with a screw from the scrubber cover assembly, then the chassis lifts out of the lower cover to free the tie bar. The guide doesn't say what the stops are for, and no list gives the kit a part number.
Where Pentair's documents disagree
- Cleaning time. The manual's operation page recommends a two-hour cycle for an average 15 by 30 ft. pool. Its safety page says about 4 to 6 hours.
- The chassis kit. The 2024 manual lists it as 360427. The 2021 sheet gives 360391, the number the Racer's lists use for its chassis kit with tie bar.
- The Racer's pages. The catalog prices five of the same part numbers differently there: the 10 ft. hard hose, 360266, at $95.77 rather than $162.87; the wall fitting screen, E24, at $27.64 rather than $16.40; the wall adapter, LL23PM, at $53.69 rather than $15.72; the in-line filter, 360392, at $56.13 rather than $65.32; and the float, 360270, at $101.10 rather than "call". This page uses the Racer LS's own pages.
- The turbine, 360414. The Racer LS's lists call it the turbine housing kit, and the Racer's the turbine kit. The catalog prices it the same on both.
- The in-line filter's place. The manual puts it about 18 in. from the wall fitting and converts that to 45.7 mm; 18 in. is about 457 mm.
- The tune-up kit, 360417. The 2021 sheet lists a scrubber among its contents, with a bag, a drive shaft, two large tires, two small wheels and bearings, but neither list gives the Racer LS a scrubber of its own, only a scrubber cover kit, 360421.
- The warranty. No document gives a term, and Pentair's warranty table doesn't list the Racer LS.
Which model do you have?
The model number is on the cleaner label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Feed hose | Back-up valve |
|---|---|---|---|
| Racer LS | 360330 | Two 10 ft., plus a 10 ft. lead | 360428 |
Note on Racer LS: Pentair's only item number for it, in a 22.5 lb carton. Its page now carries the discontinued notice. The Racer is a separate model, with different covers, chassis, reversing and hose. | |||
Pentair Racer LS parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The stainless steel screen inside the wall fitting, a second filter for whatever gets past the pool filter. The manual says to clean it once a week, because a dirty one can damage the cleaner: turn off the booster and then the filter pump, pull the wall fitting, rinse the screen and push it back. Never run without it; that can damage the cleaner and void the warranty. A screen that keeps getting dirty points at the pool's filter system. $16.40 US list.
A filter housing in the hose about 18 in. from the wall fitting, with a debris screen inside. Check it whenever you empty the bag. With the cleaner out on the deck, twist the cap off the housing, take the screen out, clear it and flush it with a hose, then put it back and thread the cap on hand tight. The screen alone is 360437. $65.32 US list.
The valve in the lead hose that pulls the cleaner away from where it is, about every 3-1/2 minutes, for about 15 seconds, so it gets past obstructions and covers the pool at random. The manual's first check for a cleaner stuck on the steps or not reversing is that this valve cycles; the next is the wheel speed, then both screens. $144.29 US list.
The adapter that screws into the return and holds the wall fitting. If the one in the wall isn't Pentair's, the manual says to press out its red or blue flow restrictor plate with your thumbs before fitting the cleaner; left in, it starves the cleaner, which runs slowly and takes longer to clean. Its troubleshooting table checks for a plate too. $15.72 US list.
The quick-lock fitting the hose connects to, with the flow valve you turn with a flathead screwdriver. For a noisy booster, the manual says to check both pumps are moving water, then that the wall fitting is properly installed; if it leaks, an O-ring may need replacing. If the noise goes on, it says to call a pool professional about the booster. $56.54 US list.
The manual's fixes for tangling: check the hose isn't too long, that it floats with its floats about two feet apart, that it has no kinks, and that every swivel spins freely. Replace any swivel that's tight. A hose stored coiled straightens after 12 to 24 hours laid straight in the sun. $80.78 US list.
The manual says to clear any debris tangled in a rear wheel that drags or won't spin. Free-spinning rear wheels are on its list for a slow cleaner, too, and it says to replace them if they don't. $101.10 US list.
The manual says the tires protect the pool's floor and give traction, and wear out and need replacing occasionally. Debris jammed in the gear teeth of a front wheel can stop the cleaner: turn the front wheels backward by hand to free it. The large wheel kit is 360235, at $70.38. $74.04 US list.
A cleaner that tilts to one side usually has a full bag, the manual says, though it tips onto two wheels for a moment in some turns. Replace the bag when the fabric is torn or punctured. This kit comes without the collar, 360241 at $19.28. It's easier to empty dry, and a second bag can go on while the first dries. $72.90 US list.
If you are doing the job anyway
Prices are the 2025-2026 catalog's, which lists 23 Racer LS parts and gives 22 of them a price; the rest are from the 2024 manual and the 2021 sheet, unpriced.
Hook-and-loop bag with a new collar
The bag kit comes without its collar, so a cleaner whose collar is cracked or lost needs both.
- Debris bag, hook-and-loop, without collar360240
- 360241360241
Pentair Racer LS manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Racer LS installation and user's guide (P/N 371824 Rev. B, 2/16/24), English, Spanish and French, with the parts list on page 11manual
- Racer LS product page, with the discontinued noticespec
- Pentair Pool 2025-2026 product catalog: Racer LS replacement parts and US list prices on pages 306 and 307diagram
- Racer LS replacement parts sheet (PDF 2021)diagram
- Tie bar stop kit installation guide, Racer and Racer LS (P/N 371209 Rev. A, 10/22/18)guide
- Racer LS brochure (P1-181, December 2021)spec
- Pentair pool product warranty informationspec
Pentair Racer LS warranty
No term in its documents, and Pentair's current warranty table doesn't list it
The 2024 manual mentions a warranty card and says running without the wall fitting's debris screen can damage the cleaner and void the warranty, but it gives no term, and neither does the 2021 brochure. Pentair's warranty table doesn't list the Racer LS; it gives the pressure-side Platinum one year and its other cleaners two. The brochure places it in Pentair's TradeGrade family, sold through pool professionals, but Pentair's current TradeGrade list, revised 23 October 2026, doesn't include it.
Manufacturer’s termsPentair Racer LS complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
50 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 360422 | Top front cover kit | |
| 2 | 360425 | Rear cover kit | |
| 3 | 360424 | Bottom cover kit | |
| 4 | 360427 | Chassis kit | The 2024 manual's number |
| 4 | 360391 | Chassis kit, on the 2021 sheet | The Racer's chassis kit with tie bar |
| 5 | 360426 | Grill kit | |
| 6 | 360423 | Side covers kit | |
| 7 | 360235 | Large wheel kit | $70.38 US list |
| 8 | 360236 | Small wheel kit what goes wrong | $101.10 US list |
| 9 | 360237 | Large tires kit what goes wrong | $74.04 US list |
| 10 | 360240 | Debris bag kit, hook-and-loop, without collar what goes wrong | $72.90 US list |
| 11 | 360241 | Debris bag collar kit | $19.28 US list |
| 12 | 360242 | Vacuum tube kit | $56.13 US list |
| 13 | 360243 | Debris valve kit | |
| 14 | 360244 | Sweep hose kit | $86.39 US list |
| 15 | 360245 | Sweep hose scrubber kit | $21.56 US list |
| 16 | 360249 | Feed hose swivel kit what goes wrong | $80.78 US list |
| 17 | 360250 | Quick connector to the cleaner | $39.86 US list |
| 18 | 360251 | Wall fitting, listed as the feed line wall connector kit what goes wrong | $56.54 US list |
| 19 | 360252 | Feed line connector kit | |
| 20 | 360253 | Drive shaft kit | $36.25 US list |
| 21 | LLC55PMB | Wheel screw kit | |
| 22 | 360255 | Screw kit | |
| 23 | 360419 | Thrust hose kit | |
| 24 | 360258 | Rubber button kit | |
| 25 | 360414 | Turbine housing kit | $32.39 US list |
| 26 | 360260 | Venturi manifold kit | |
| 27 | 360416 | Water management kit | $21.60 US list |
| 28 | 360420 | Turbine hose kit | |
| 29 | 360417 | Tune-up kit | Not priced in the 2025-2026 catalog |
| 30 | 360431 | Hose assembly, complete | $803.18 US list |
| 31 | 360429 | Lead hose, 2.5 ft. | |
| 32 | 360430 | Lead hose, 7.5 ft. | |
| 33 | 360266 | Hard feed hose, 10 ft. | $162.87 US list |
| 34 | E24 | Wall fitting debris screen what goes wrong | $16.40 US list |
| 35 | LL23PM | Threaded wall adapter what goes wrong | $15.72 US list |
| 36 | EB10G | Sweep hose wear ring | |
| 37 | 360270 | Feed hose float | The catalog says call for the price |
| 38 | 360268 | Feed hose O-ring kit | |
| 39 | 360428 | Back-up valve kit what goes wrong | $144.29 US list |
| 40 | 360421 | Scrubber cover kit | |
| 41 | 360418 | Weight kit, listed as SS | |
| 42 | 360415 | Manifold kit | $67.21 US list |
| 43 | 360434 | Axle replacement kit | |
| 44 | EC64 | Wheel washer kit | |
| 45 | 360436 | Sweep hose cap | |
| 46 | 360392 | In-line filter assembly what goes wrong | $65.32 US list |
| 47 | 360437 | Replacement in-line filter screen kit | |
| — | 360320 | Quick disconnect hose connector kit | $6.47 US list; not in the manual |
| — | 360318 | Sweep tail quick connect | The 2021 sheet only |