Pentair · Challenger
Pentair Challenger
Pentair's discontinued Challenger pumps, high pressure and high flow: the F and A ratings, the parts still listed, the quick kit and the manual's mixed labels.
Discontinued. Replaced by the Max-E-Pro, SuperMax VS or IntelliPro VSF, which Pentair's Challenger pages suggest. Everything on this page still applies to the units already installed.

The Challenger was Pentair's self-priming pool pump in two series: High Pressure and High Flow. Both of Pentair's product pages now mark it discontinued. They say Pentair no longer makes it, suggest asking a pool professional whether any are left in stock, and offer three pumps as replacements: the Max-E-Pro, the SuperMax VS and the IntelliPro VSF. Pentair's own Max-E-Pro page now marks that pump discontinued as well.
Parts are another matter. Pentair's 2025-2026 catalog still lists four pages of them, with prices. This page is for keeping one running.
Which one you have
The two series share the motors, seal, seal plate, housing, strainer pot, lid and basket. They differ in the impeller and diffuser, and in the clamp. The power ends tell them apart: CH- for High Pressure and CF- for High Flow.
Pentair's pages list 22 High Pressure and 16 High Flow models, from 1/2 to 3 horsepower, all with 2-inch ports. The High Pressure page gives each model's code, like CHII-NI-1FE; the High Flow page gives only the item number. The parts lists also cover a 5 HP High Flow and 3-phase motors that the product pages don't.
The rating at the end of the code is what the parts follow. Each impeller and diffuser is listed against ratings like 1F, 1-1/2A and 1FE. The catalog never says what the letters mean, but its tables pair every A rating with the F one size smaller: the 1-1/2A shares the 1F's impeller. Pentair's High Pressure page gives the pairs nearly the same service-factor horsepower, too: 1.65 for both the 1F and the 1-1/2A. The manual lists the FE ratings with the F ratings of the same size.
So a CHII-NI-1-1/2FE takes the High Pressure impeller for 1-1/2F: 355315Z. The High Pressure models with codes ending FET, 348154 to 348157, aren't in either table, so ask a dealer before ordering an impeller for one. The High Flow page gives no codes at all, so read the code on your pump's own label.
Impellers and diffusers
High Pressure, at 2025-2026 US list:
- 1/2F, 3/4A: impeller 355147Z, $87.14. The catalog lists no diffuser; the manual gives 355148.
- 3/4F, 1A: impeller 355187, $88.88; diffuser 355188Z, $51.87.
- 1F, 1-1/2A: impeller 355369Z, $95.25; diffuser 355188Z.
- 1-1/2F, 2A: impeller 355315Z, $95.25; diffuser 355270Z, $53.60.
- 2F, 2-1/2A: impeller 355604Z, $95.25; diffuser 355545Z, $88.57.
- 3F: impeller 355544, $118.26; diffuser 355545Z.
The catalog adds a date to the 2F and 2-1/2A pumps. Impeller 355604Z is for pumps built after 1 October 1992, and one built before that takes both the 355545Z diffuser and the 355604Z impeller together.
High Flow:
- 1/2F, 3/4A: impeller 355043, $87.14; diffuser 355029Z, $64.73.
- 3/4F, 1A: impeller 355067Z, $95.25; diffuser 355029Z.
- 1F, 1-1/2A: impeller 355074Z, $95.25; diffuser 355077, $64.73.
- 1-1/2F, 2A: impeller 355086Z, $95.25; diffuser 355077.
- 2F, 2-1/2A: impeller 355093, $92.18; diffuser 355094Z, $69.39.
- 3F at 50 Hz, 5F at 60 Hz: impeller 355068, $88.88; diffuser 355069, $59.85.
The diffuser O-ring differs too: 355331Z at $5.03 on High Pressure pumps and the 5 HP High Flow, 355030Z at $15.00 on the other High Flow pumps.
Where the manual and the catalog disagree
The manual is from 2016 and the catalog is current, and they give three parts different jobs:
- 355317: the catalog calls it a mounting plate. The manual's High Pressure table lists it as the diffuser spacer.
- 355329 and 355330: the manual calls 355329 the seal plate square ring and 355330 the front housing O-ring. The catalog calls 355329Z the front housing O-ring and 355330Z the strainer pot flange O-ring.
- The band clamp: the manual gives 354629 for both series. The catalog lists 354629Z for High Flow and 355320Z, at $138.74, for High Pressure.
The catalog is the newer document and the one with prices, so the parts list follows it, with the manual's label noted. If the part in your hand doesn't match the description, check the number on it.
Replacing the seal
A drip between the motor and the pump is the shaft seal. The manual says running the pump dry damages it and makes the pump leak, and that the seal can be changed without cutting into the plumbing. The Challenger Quick Kit, 356199, at $58.45, has the seal and every O-ring the job uncovers, for $12.62 more than the seal alone. The pump leak guide covers telling a seal leak from the others.
The manual's tools are an adjustable wrench, a 1/4-inch flat screwdriver, a 9/16-inch open-end wrench and a rubber mallet. Its steps:
- Close the suction and discharge valves, and take out the drain plugs by hand.
- Loosen the band clamp knob counterclockwise and pull the motor end away from the housing. If the clamp sticks, tap its top with the mallet.
- Take out the three diffuser screws, then the diffuser and its spacer.
- Take out the impeller screw. It's a left-hand thread, so it loosens clockwise.
- Hold the motor shaft with the screwdriver through the back of the motor, and unscrew the impeller counterclockwise.
- Lift off the rotating half of the seal, and set it down flat side down, away from dirt.
- Unbolt the seal plate from the motor, four bolts, lay it face down and tap out the ceramic seat.
Then press the new ceramic seat in with your thumbs and wipe it clean, bolt the seal plate back on, and seat the spring half on it, carbon face to ceramic. Grease the motor shaft's thread, screw the impeller on, and fit the impeller screw, which tightens counterclockwise. Refit the spacer and diffuser, put the housing back, and tighten the clamp. The manual says the knob should end up parallel to the pad. Put the drain plugs back hand-tight.
The lid, priming and running dry
The lid comes off counterclockwise and goes back on pressed down and turned clockwise. The manual says to clean and look at the lid O-ring every time, and calls lubricating it with silicone lubricant each time good practice. Look at the basket at least once a week.
To prime, fill the pot with water up to the inlet, put the lid back, open the filter's air relief valve and stand clear, then start the pump. Close the valve when water comes out of it. It should prime within 30 minutes; if it hasn't, switch it off. Two-speed models should prime on high. The priming guide covers the causes the manual lists: no water in the pot, a loose lid or bad O-ring, low pool water, a clogged basket, a closed valve, low speed, or an air leak in the suction line.
Installing it
The manual wants the pump at least 5 feet from the inside of the pool wall, 3 feet from a heater's outlet, and no more than 10 feet above the water. Leave 3 inches behind the motor and 12 inches above the pot. Give the suction pipe a straight run of at least five times its diameter before the pump, and don't put a 90-degree elbow straight into either port. Seal threads with tape or a sealant made for plastic, never anything petroleum-based, and tighten fittings by hand plus 1-1/2 turns.
Winter
Freeze damage isn't covered. Switch off the breaker, take out the two drain plugs and keep them in the basket, and cover the motor without wrapping it in plastic. In mild climates the manual says running the filter all night through a frost is enough.
Replacing it
Pentair names three replacements, and its catalog has parts for fitting two of its current pumps where a Challenger was. The WhisperFlo XF needs riser plate 400012, at $106.23, sold separately. For the IntelliFlo3 VSF, Pentair lists retrofit riser base kits for Challenger models: 357832Z for 1.5 HP pumps and 357833Z for 3 HP. Replacing a pool pump covers the rest.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | SKU | Series | Volts | Service factor |
|---|---|---|---|---|---|
| CHII N1 1FET | 1 | 348154 | High pressure | 115/208 to 230 | 1.65 |
Note on CHII N1 1FET: A newer TEFC model; neither the manual nor the catalog maps it to an impeller. | |||||
| CHII N1 1-1/2FET | 1-1/2 | 348155 | High pressure | 208 to 230 | 1.47 |
Note on CHII N1 1-1/2FET: A newer TEFC model; neither the manual nor the catalog maps it to an impeller. | |||||
| CHII N1 2FET | 2 | 348156 | High pressure | 208 to 230 | 1.3 |
Note on CHII N1 2FET: A newer TEFC model; neither the manual nor the catalog maps it to an impeller. | |||||
| CHII N1 3FET | 3 | 348157 | High pressure | 208 to 230 | 1.15 |
Note on CHII N1 3FET: A newer TEFC model; neither the manual nor the catalog maps it to an impeller. | |||||
| CHII-NI-1/2FE | 1/2 | 345212 | High pressure | 115/208 to 230 | 1.90 |
| CHII-NI-3/4FE | 3/4 | 345213 | High pressure | 115/208 to 230 | 1.67 |
| CHII-NI-1FE | 1 | 345205 | High pressure | 115/208 to 230 | 1.65 |
| CHII-NI-1-1/2FE | 1-1/2 | 345206 | High pressure | 208 to 230 | 1.47 |
| CHII-NI-2FE | 2 | 345208 | High pressure | 208 or 230 | 1.30 |
| CHII-NI-3FE | 3 | 345209 | High pressure | 208 to 230 | 1.15 |
| CHII-NI-2-1/2AE | 2-1/2 | 346209 | High pressure | 208 to 230 | 1.15 |
| CHI-NI-1/2F | 1/2 | 345202 | High pressure | 115/230 | 1.90 |
Note on CHI-NI-1/2F: Pentair prints the model CHI-NI-1/2F, without the second I. | |||||
| CHII-NI-3/4F | 3/4 | 345203 | High pressure | 115/230 | 1.67 |
| CHII-NI-1F | 1 | 345204 | High pressure | 115/230 | 1.65 |
| CHII-NI-1-1/2F | 1-1/2 | 345201 | High pressure | 115/230 | 1.50 |
| CHII-NI-2F | 2 | 345218 | High pressure | 230 | 1.30 |
| CHII-NI-3F | 3 | 345219 | High pressure | 230 | 1.15 |
| CHII-NI-3/4A | 3/4 | 346203 | High pressure | 115/230 | 1.25 |
| CHII-NI-1A | 1 | 346204 | High pressure | 115/230 | 1.25 |
| CHII-NI-1-1/2A | 1-1/2 | 346206 | High pressure | 115/230 | 1.10 |
| CHII-NI-2A | 2 | 346201 | High pressure | 115/230 | 1.10 |
| CHII-NI-2-1/2A | 2-1/2 | 346249 | High pressure | 230 | 1.04 |
| 343229 | 2-1/2 | — | High flow | 230 | 1.04 |
| 343232 | 3/4 | — | High flow | 115/230 | 1.25 |
| 343233 | 1 | — | High flow | 115/230 | 1.25 |
| 343234 | 1-1/2 | — | High flow | 115/230 | 1.10 |
| 343240 | 2 | — | High flow | 115/230 | 1.10 |
| 342248 | 2 | — | High flow | 230 | 1.30 |
| 348158 | 1 | — | High flow | 115/208 to 230 | 1.65 |
| 348159 | 1-1/2 | — | High flow | 208 to 230 | 2.21 |
| 348160 | 2 | — | High flow | 208 to 230 | 2.6 |
| 342235 | 1 | — | High flow | 115/208 to 230 | 1.65 |
| 342236 | 1-1/2 | — | High flow | 208 to 230 | 1.47 |
| 342238 | 2 | — | High flow | 208 to 230 | 1.30 |
| 342232 | 1/2 | — | High flow | 115/230 | 1.90 |
| 342233 | 3/4 | — | High flow | 115/230 | 1.67 |
| 342234 | 1 | — | High flow | 115/230 | 1.65 |
| 342231 | 1-1/2 | — | High flow | 115/230 | 1.50 |
Pentair Challenger parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The shaft seal and the O-rings the job uncovers: the diffuser, front housing, pot flange and lid O-rings and both drain plug O-rings, items 4, 13, 14, 16, 21, 24 and 27. At $58.45 US list it costs $12.62 more than the seal alone, 354545S at $45.83. The manual says running the pump dry damages the seal and makes the pump leak.
The ceramic seat and the rotating spring seal. It can be changed without cutting the plumbing: the motor, seal plate, diffuser and impeller come away from the housing once the band clamp is off. Keep both faces clean and unscratched; the manual says a damaged face leaks. Pentair also lists an ozone- and salt-resistant seal, 356210S, at $51.07. $45.83 US list.
The manual's troubleshooting names a damaged lid O-ring and a loose lid among the causes of a pump that won't prime. Clean and inspect it every time the pot is opened, and it says lubricating it with silicone lubricant each time is good practice. $6.04 US list.
The clear lid, twisted counterclockwise to come off and pressed down and twisted clockwise to go back on. $103.36 US list. Its O-ring is 350013Z.
Every model except the 3 HP, which takes a stainless basket, 355441 at $302.65; a 5 HP High Flow takes 355901 at $656.04. The manual says to look at the basket at least once a week and replace it if it's cracked. $65.69 US list.
The black plate the ceramic seat presses into, bolted to the motor with four bolts. The same on both series. $163.11 US list.
The High Pressure band clamp, complete, at $138.74 US list. The High Flow's is 354629Z at $127.36, and the manual gives 354629 for both. Its knob is 174882 for a removable bolt or 175025Z for a captured T-bolt, $56.32 either way. The manual says the knob should sit parallel to the pad when the clamp is on right.
A left-hand thread: it loosens clockwise and tightens counterclockwise. Take it out before unscrewing the impeller, holding the motor shaft with a screwdriver through the back of the motor. $3.61 US list.
Two on the housing, turned by hand: no tools to remove them, hand-tight only to put them back. Each takes an O-ring, 192115Z at $4.04. $8.07 US list.
If you are doing the job anyway
Opening the pump for the seal uncovers every O-ring in it. Numbers carry the Z the 2025-2026 catalog prints; the manual leaves it off.
Seal job
The Quick Kit has the seal and the six O-rings the job puts in your hands, for $12.62 more than the seal alone, and the impeller screw comes out on the way to the seal.
- Challenger Quick Kit356199
- Impeller locking screw355389Z
Lid that leaks air
The manual names a loose lid and a damaged lid O-ring among the reasons a pump won't prime, and the O-ring costs $6.04.
- Strainer pot lid355301Z
- Lid O-ring350013Z
Pentair Challenger manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Challenger centrifugal pump installation and user's guide (P/N 355031 Rev. F, 2016)manual
- Challenger High Pressure product page: the discontinued notice and every modelspec
- Challenger High Flow product page: the discontinued notice and every modelspec
- Pentair Pool 2025-2026 product catalog, pump parts: the Challenger on pages 440 to 443, with US list pricesdiagram
- Challenger High Pressure replacement parts, the older catalog pages (PDF 2016)diagram
- Challenger High Flow replacement parts, the older catalog pages (PDF 2016)diagram
- Pentair pool and spa equipment warranty informationspec
Pentair Challenger warranty
One year on Pentair's row for single-speed pumps, or two on its row for single-phase TEFC Super Duty pumps
Pentair's warranty table doesn't name the Challenger. It gives single-speed and booster pumps one year and single-phase TEFC Super Duty pumps two, without saying which row a Challenger falls in. The manual adds that freeze damage isn't covered and that wiring the motor to the wrong voltage voids the warranty. The pump is discontinued, so the warranty only matters on one installed from a dealer's remaining stock.
Manufacturer’s termsPentair Challenger complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
106 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 354804S | Motor, 3/4 HP, single-phase TEFC, 115/208-230 V | $593.93 US list |
| 1 | 354822S | Motor, 1 HP, single-phase TEFC, 115/208-230 V | $726.14 US list |
| 1 | 354824S | Motor, 1-1/2 HP, single-phase TEFC, 208-230 V | $855.29 US list |
| 1 | 354816S | Motor, 2 HP, single-phase TEFC, 208-230 V | $1,019.06 US list |
| 1 | 354818S | Motor, 3 HP, single-phase TEFC, 208-230 V | High Pressure page. $1,331.64 US list |
| 1 | 354806S | Motor, 1 HP, 3-phase, square flange, 208-230/460 V | High Pressure page. $688.51 US list |
| 1 | 354808S | Motor, 1-1/2 HP, 3-phase, 208-230/460 V | High Pressure page. $856.03 US list |
| 1 | 354810S | Motor, 2 HP, 3-phase, 208-230/460 V | High Pressure page. $955.02 US list |
| 1 | 354812S | Motor, 3 HP, 3-phase, 208-230/460 V | High Pressure page. $1,251.71 US list |
| 1 | 354814S | Motor, 5 HP, 3-phase, 208-230/460 V | High Pressure page. $1,521.51 US list |
| 2 | 355004Z | Seal plate, black what goes wrong | Both series. $163.11 US list |
| 3 | 355317 | Plate, mount, 3/4F to 3F and 1A to 2-1/2A | High Pressure. $23.84 US list. The manual calls 355317 the diffuser spacer |
| 3 | 355495Z | Plate, mounting, 5F | High Flow. $22.05 US list |
| 4 | 354545S | Seal, 5/8 in. mechanical what goes wrong | Both series. $45.83 US list |
| 4 | 356210S | Seal, mechanical, ozone and salt resistant | $51.07 US list |
| 5 | 355147Z | Impeller, High Pressure, 1/2F and 3/4A | $87.14 US list. The manual adds 1/2FE |
| 5 | 355187 | Impeller, High Pressure, 3/4F and 1A | $88.88 US list. The manual adds 3/4FE |
| 5 | 355369Z | Impeller, High Pressure, 1F and 1-1/2A | $95.25 US list. The manual adds 1FE |
| 5 | 355315Z | Impeller, High Pressure, 1-1/2F and 2A | $95.25 US list. The manual adds 1-1/2FE |
| 5 | 355604Z | Impeller, High Pressure, 2F and 2-1/2A | $95.25 US list. Used on 2F and 2-1/2A pumps built after 1 October 1992; the manual adds 2FE and 2-1/2AE |
| 5 | 355544 | Impeller, High Pressure, 3F | $118.26 US list. The manual adds 3FE |
| 5 | 355043 | Impeller, High Flow, 1/2F and 3/4A | $87.14 US list |
| 5 | 355067Z | Impeller, High Flow, 3/4F and 1A | $95.25 US list |
| 5 | 355074Z | Impeller, High Flow, 1F and 1-1/2A | $95.25 US list. The manual adds 1FE |
| 5 | 355086Z | Impeller, High Flow, 1-1/2F and 2A | $95.25 US list. The manual adds 1-1/2FE |
| 5 | 355093 | Impeller, High Flow, 2F and 2-1/2A | $92.18 US list. The manual adds 2FE |
| 5 | 355068 | Impeller, High Flow, 3F 50 Hz and 5F 60 Hz | $88.88 US list |
| 6 | 355148 | Diffuser, High Pressure, 1/2F, 3/4A and 1/2FE | In the manual; not in the 2025-2026 catalog |
| 6 | 355188Z | Diffuser, High Pressure, 3/4F, 1F, 1A and 1-1/2A | $51.87 US list |
| 6 | 355270Z | Diffuser, High Pressure, 1-1/2F and 2A | $53.60 US list |
| 6 | 355545Z | Diffuser, High Pressure, 3F, 2-1/2A and 2F | $88.57 US list. The catalog says 2F and 2-1/2A pumps built before 1 October 1992 take it with impeller 355604Z |
| 6 | 355029Z | Diffuser, High Flow, 1/2F, 3/4F, 3/4A and 1A | $64.73 US list |
| 6 | 355077 | Diffuser, High Flow, 1F, 1-1/2F, 1-1/2A and 2A | $64.73 US list |
| 6 | 355094Z | Diffuser, High Flow, 2F and 2-1/2A | $69.39 US list |
| 6 | 355069 | Diffuser, High Flow, 3F 50 Hz and 5F 60 Hz | $59.85 US list |
| — | 355384 | Diffuser spacer, High Pressure, 1/2F, 3/4A and 1/2FE | In the manual |
| — | 355028 | Diffuser spacer, High Flow, 1/2F to 1A | In the manual |
| — | 355078 | Diffuser spacer, High Flow, 1F to 2A and FE | In the manual |
| — | 355095 | Diffuser spacer, High Flow, 2F, 2-1/2A and 2FE | In the manual |
| 7 | 355320Z | Band clamp assembly, High Pressure what goes wrong | $138.74 US list. The manual gives 354629 for both series |
| 7 | 354629Z | Band clamp assembly, High Flow | $127.36 US list |
| 8 | 355468Z | Front housing, black | Includes items 16 and 17, the drain plug and its O-ring, per the High Flow page. $238.09 US list |
| 8 | 355469 | Front housing, almond | $237.44 US list |
| 9 | 070429Z | Bolt, 3/8-16 x 7/8 in. stainless hex head | Four. $5.03 US list |
| 10 | 355389Z | Screw, impeller locking what goes wrong | Left-hand thread. $3.61 US list |
| 11 | 355305 | Base | With the dual-radius motor support adapter for 5-5/8 in. and 6-1/2 in. motors. $79.21 US list |
| 12 | 355334Z | Screw, 8-32 x 1 in. stainless hex washer head | Three. $5.03 US list |
| 13 | 355331Z | O-ring, diffuser | High Pressure, and the 5 HP High Flow. $5.03 US list |
| 13 | 355030Z | O-ring, diffuser | High Flow except 5 HP. $15.00 US list |
| 14 | 355329Z | O-ring, front housing | $26.90 US list. The manual calls 355329 the seal plate square ring |
| 15 | 355335 | Screw, 5/16-18 x 1/2 in. stainless hex washer head | Two. The catalog notes say pool pumps have every item except 15. The 2016 sheet |
| 16 | 192115Z | O-ring, drain plug | $4.04 US list |
| 17 | 357161Z | Plug, 1/4 in. drain what goes wrong | $8.07 US list |
| 18 | 152060 | Bolt, 5/16-18 x 4 in. carriage | For the earlier-style clamp band. $17.17 US list |
| 19 | 072173 | Washer, 5/16 in. stainless flat | $2.84 US list |
| 20 | 174882 | Knob, clamp, removable bolt | $56.32 US list |
| 20 | 175025Z | Knob, clamp, captured T-bolt | $56.32 US list |
| 21 | 355330Z | O-ring, strainer pot flange | $2.89 US list. The manual calls 355330 the front housing O-ring |
| 22 | 354265 | Screw, 5/16-18 x 3/4 in. stainless hex washer head | Four; the strainer pot bolts. The manual and 2016 sheet |
| 25 | 355300Z | Strainer pot, black | Includes items 23 and 24, per the High Flow page. $234.74 US list |
| 26 | 355318Z | Basket, plastic what goes wrong | All except 3F. $65.69 US list |
| 26 | 355441 | Basket, stainless, 3F only | $302.65 US list; printed 355441Z on the High Flow page |
| 26 | 355901 | Basket, stainless, 5F | High Flow. $656.04 US list |
| 27 | 350013Z | O-ring, lid what goes wrong | $6.04 US list |
| 27 | 152509Z | Square ring, 8-1/2 in., 5 HP only | High Flow. $11.74 US list |
| 28 | 355301Z | Lid, strainer pot what goes wrong | $103.36 US list |
| 28 | 354112 | Lid, strainer pot, chemical resistant | The 2016 sheet |
| 29 | 552377 | Bushing, reducer, 1/2F, 3/4F, 3/4A and 1A | High Pressure. The 2016 sheet |
| 31 | 154527Z | Wrench, 8-1/2 in. | High Flow, 5 HP. $47.05 US list |
| — | U30-74SS | Motor bolt | Four. In the manual |
| — | 356199 | Challenger Quick Kit what goes wrong | Items 4, 13, 14, 16, 21, 24 and 27. $58.45 US list |
| — | 359507Z | Pot assembly, black, with plastic bracket | All except 3F and 5F; items 23 to 28. $413.22 US list |
| — | 357391 | Pot assembly, black, with stainless basket | 3F only. The 2016 sheet |
| — | 355302 | Housing, booster pump | $328.58 US list |
| — | 355309 | Union kit | The 2016 sheet |
| — | 401014Z | Motor end cap and screw | $41.72 US list |
| — | 357924Z | Fan guard kit, TEFC and Super-Duty | Price on request |
| — | 355670 | Power end, CH-N1-1/2F and 3/4A, 115/208-230 V | Items 1 to 6, 9, 10, 12 and 13. Price on request |
| — | 355671 | Power end, CH-N1-3/4F and 1A | Price on request |
| — | 355672 | Power end, CH-N1-1F and 1-1/2A | Price on request |
| — | 355669 | Power end, CH-N1-1-1/2F and 2A | Price on request |
| — | 355674 | Power end, CH-N1-1FE and 1-1/2AE | Price on request |
| — | 355675 | Power end, CH-N1-1-1/2FE and 2AE, 208-230 V | Price on request |
| — | 355676 | Power end, CH-N1-2FE and 2-1/2AE, 208-230 V | Price on request |
| — | 355637 | Power end, CF-N1-3/4F and 1A, 115/208-230 V | High Flow. Price on request |
| — | 355984 | Power end, CF-N1-3/4FE and 1AE | High Flow. Price on request |
| — | 355639 | Power end, CF-N1-1-1/2FE and 2AE, 208-230 V | High Flow. Price on request |
| — | 355986 | Power end, CF-N1-2FE and 2-1/2AE, 208-230 V | High Flow. Price on request |
| — | 355641 | Power end, CF-N2-1F and 1-1/2A, two-speed, 230 V | High Flow. Price on request |
| — | 345211 | Power end, CFII-N1-5FE | High Flow. Price on request |
| — | 355019S | Motor, 1/2F and 3/4A, single speed | The manual's motor table |
| — | 355021S | Motor, 3/4F and 1A, single speed | The manual's motor table |
| — | 355023S | Motor, 1F and 1-1/2A, single speed | The manual's motor table |
| — | 355025S | Motor, 1-1/2F and 2A, single speed | The manual's motor table |
| — | 355027S | Motor, 2F and 2-1/2A, single speed | The manual's motor table |
| — | 355034S | Motor, 3F, single speed | The manual's motor table |
| — | 355009S | Motor, 1/2FE and 3/4FE | The manual's motor table |
| — | 355011S | Motor, 1FE | The manual's motor table |
| — | 355013S | Motor, 1-1/2FE | The manual's motor table |
| — | 355015S | Motor, 2FE and 2-1/2AE | The manual's motor table |
| — | 355017S | Motor, 3FE | The manual's motor table |
| — | 355375S | Motor, 3/4F and 1A, two-speed | The manual's motor table |
| — | 355376S | Motor, 1F and 1-1/2A, two-speed | The manual's motor table |
| — | 355377S | Motor, 1-1/2F and 2A, two-speed | The manual's motor table |
| — | 355378S | Motor, 2F and 2-1/2A, two-speed | The manual's motor table |
| — | 400012 | Riser plate, WhisperFlo XF to Challenger | For replacing a Challenger with an XF. $106.23 US list |