Skip to content
PoolBuff

Pentair · MicroBrite

Pentair MicroBrite

Pentair's 3.5-inch LED light that threads into a return fitting: every version, the fittings it suits, the GloBrite niche option and the manual's mixed counts.

A small LED pool light on wet stone coping by a pool: a black knurled ring around its lens, a white threaded ring behind it, and a clear body with a green circuit board inside
Generated image, checked against Pentair’s own product photographs. It is not a photograph of this unit.

MicroBrite is Pentair's smallest pool light: 3.5 inches long, 12 volts and 12 watts, in color, white, warm white and a red-orange version for oceanfront pools under sea turtle rules. It needs no niche. It threads into a standard 1.5-inch pool wall fitting, the same kind as a return jet, so it can go where a niche wouldn't fit. Pentair also says it suits many pools with old fiber-optic lighting. It can face out from a wall or, where nobody swims, straight up.

Its sibling, the GloBrite, sits in its own niche instead, and the MicroBrite-G versions are made to fit that niche.

Which one

  • Color: five fixed colors and seven shows, at one brightness. 620424, 620425 and 620426 for 50, 100 and 150 feet of cord.
  • White: three brightness levels, 620428 to 620430.
  • Warm white: three brightness levels, 602156, 620457 and 602155. Pentair says it gives the tone of an incandescent light.
  • Turtle Edition, 602157: a 620-nanometer red-orange light, for oceanfront pools where local rules protect sea turtles. 150 feet of cord only.
  • MicroBrite-G: color, white and warm white, made to fit a GloBrite niche or Pentair's ColorVision bubbler, with 100 or 150 feet of cord.

Pentair also sells three online versions, EC-620425 (color), EC-620429 (white) and EC-620457 (warm white), all with 100 feet of cord. Their warranty is shorter, as the warranty section below explains.

The fitting it goes in

The light comes with a white threaded ring, 620460, already on it. That ring screws into the female threads of a 1-1/2-inch wall fitting, NPT or NPS. The manual lists the fittings it suits: six of Pentair's, Hayward's SP1022, four of Waterway's and three of CMP's. They're all in the parts list.

For a fiber-optic retrofit, the manual says to check that the light fits before taking the old system out, and that the conduit the fibers ran in meets the electrical code for pools.

It doesn't need a bond wire. Pentair says the light and the wall fitting make a nonmetallic, low-voltage system, and that it needs no bonding or grounding when it runs from a pool-rated 100 or 300 W isolation transformer, citing the National Electrical Code's exceptions in Articles 680.6 and 680.23.

Facing up is allowed, with the light at least 4 inches below the water. Pentair recommends that only where nobody swims, such as up-lighting a vanishing edge. On a wall, the top of the lens goes at least 4 inches down.

Installing it

The manual's steps for a wet conduit, the usual kind:

  1. Feed the cord through the fitting and conduit to the junction box or transformer.
  2. Wrap the adapter ring's threads with thread sealant tape.
  3. Pull the cord through until 3 to 6 inches shows between the light and the fitting.
  4. Turn the light several times counterclockwise in your hand, to pre-twist the cord.
  5. Start the threads by hand, turning clockwise. The cord untwists as the light goes in.
  6. Finish with the installation tool, about five turns clockwise, until it's tight. You shouldn't be able to unscrew it with your fingers.
  7. At the box, cut the cord to leave at least 6 inches, and connect black to power and white to common.

For a dry, sealed conduit, the conduit seal o-ring, 620463, goes behind the lens, under the adapter ring, with clear silicone lubricant on the threads. The water has to be below the fitting while you do it.

Removing one is where the manual contradicts itself. Its replacement steps say to turn the light an eighth of a turn counterclockwise with the tool to release it, nearly the GloBrite manual's wording. That fits the GloBrite's niche, which locks in an eighth of a turn, not a light that threaded in about five turns. Expect to unscrew it counterclockwise with the tool, further than an eighth of a turn.

Don't put it on a dimmer

Never wire a MicroBrite to a dimmer switch. Pentair says in capitals that a dimmer damages the light permanently. The white and warm white lights dim themselves, through the wall switch:

  • 100 percent: one quick off-on.
  • 75 percent: two. It comes on at 100 and drops after a second.
  • 50 percent: three.

The color light picks its mode the same way, by counting off-on cycles: 1 to 7 are the shows, 8 to 12 the fixed colors (blue, green, red, white, magenta), 13 holds the moment in a show and 14 brings it back. It's dark while you're switching, so take care with anyone in the pool. If the power's been off for more than five seconds, it comes back in the last saved mode. Pentair says the color light syncs with its IntelliBrite lights. Pentair also says, for best results, not to mix models in one installation.

Transformers, and how many lights

A MicroBrite runs only from a safety isolation transformer. Pentair's are 619962 at 100 W and 619963 at 300 W. The junction box and transformer go at least 4 inches above the ground or 8 inches above the maximum water level, whichever is higher, and at least 48 inches from the pool's edge.

The manual gives different counts for a 100 W transformer. Its text says no more than six color lights, and a note on its wiring page says up to six of any kind. Its wiring diagram says five need a 100 W transformer, and that six or seven need a 300 W one. Five keeps you inside all of them.

On a 300 W transformer, the total of all the Pentair lights on it can't pass 300 watts, and the manual adds that it shouldn't pass 80 percent of the transformer's rating. At 12 watts a light, 80 percent of 300 is 20 MicroBrite lights.

Keep the cable to 150 feet in total, in 12-gauge wire or heavier. For a longer run, Pentair says to give each light its own 100 W transformer, and to use the 13 or 14 volt tap on long runs or with several lights.

Never run it dry

Without water around it, the manual says the color light shouldn't be on for more than 30 seconds. Fill the pool until the light is under water before you switch it on. The pool light guide compares that with other makers' lights.

When it fails

There's nothing to repair inside. Pentair calls the MicroBrite non-serviceable: the whole light, with its cord, is replaced. The manual's only troubleshooting step is to make sure 12 volts AC is reaching the light, so check the transformer and the connections at the box first.

To replace one, the manual says to disconnect it at the box, tie a fish tape to the old cord, take the light out with the tool, and pull the light, cord and tape out onto the deck. Then tie the new cord to the tape, pull it back to the box, and install the new light as above.

A MicroBrite can also replace a GloBrite without breaking into the wall. The MicroBrite-G versions fit the GloBrite niche, and the niche adapter, 618040, fits a standard MicroBrite to one. The adapter's instructions say to hand-tighten it only, because tightening it too far can damage the light for good.

Where you buy it

Every dealer number is on Pentair's TradeGrade list: sold only through pool stores, builders and service companies. The warranty is two years, a year longer than the GloBrite's, and covers parts and labor when a dealer sold it and it was professionally installed. The EC- versions are sold online, and anything bought online gets one year, parts only.

Which model do you have?

The model number is on the light label. Everything else in the range is shared — these are the parts that change with it.

ModelSKULightBrightnessFits
MicroBrite Color6204255 colors, 7 showsOne levelWall fitting

Note on MicroBrite Color: The 100 ft cord. 620424 is 50 ft and 620426 is 150 ft. Sold online as EC-620425, 100 ft only.

MicroBrite White620429White only100, 75 or 50%Wall fitting

Note on MicroBrite White: The 100 ft cord. 620428 is 50 ft and 620430 is 150 ft. Sold online as EC-620429, 100 ft only.

MicroBrite Warm White620457Warm white100, 75 or 50%Wall fitting

Note on MicroBrite Warm White: The 100 ft cord. 602156 is 50 ft and 602155 is 150 ft. Sold online as EC-620457, 100 ft only.

MicroBrite Turtle Edition602157Red-orange, 620 nmNot statedWall fitting

Note on MicroBrite Turtle Edition: 150 ft cord only. A 620 nm red-orange light for oceanfront pools in areas with rules to protect sea turtles.

MicroBrite-G Color6022145 colors, 7 showsOne levelGloBrite niche

Note on MicroBrite-G Color: The 100 ft cord. 602166 is 150 ft. Also fits Pentair's ColorVision bubbler.

MicroBrite-G White602213White only100, 75 or 50%GloBrite niche

Note on MicroBrite-G White: The 100 ft cord. 602165 is 150 ft. Also fits Pentair's ColorVision bubbler.

MicroBrite-G Warm White602215Warm white100, 75 or 50%GloBrite niche

Note on MicroBrite-G Warm White: The 100 ft cord. 602167 is 150 ft. Also fits Pentair's ColorVision bubbler.

Pentair MicroBrite parts, and what goes wrong

Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.

What is it doing?

Pentair MicroBrite manuals and documentation

Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.

Pentair MicroBrite warranty

2 years parts, Included when bought from a dealer and professionally installed labor

Two years. Pentair's warranty table lists MicroBrite color and white LED pool lights at two, against one for GloBrite. Every dealer number for the light is on Pentair's TradeGrade list, sold only through stores, builders and service companies. Pentair also sells three online versions, EC-620425, EC-620429 and EC-620457, and its warranty page gives anything bought online, including from an authorized online reseller, one year, parts only, from the date of purchase. Lighting counts toward Pentair's three-year bundle warranty for equipment bought from a dealer on one invoice with a pump and a filter.

Manufacturer’s terms

Pentair MicroBrite complete parts list

Every part number the manufacturer lists for this equipment, from its own documents. Marked rows are the ones covered above with a symptom and a diagnosis.

43 parts

PartDescriptionNote
620424MicroBrite Color, 12 V, 12 W, 50 ft cord
620425MicroBrite Color, 100 ft cord what goes wrong
620426MicroBrite Color, 150 ft cord
620428MicroBrite White, 50 ft cord
620429MicroBrite White, 100 ft cord
620430MicroBrite White, 150 ft cord
602156MicroBrite Warm White, 50 ft cord
620457MicroBrite Warm White, 100 ft cord
602155MicroBrite Warm White, 150 ft cord
602157MicroBrite Turtle Edition, 150 ft cord
602214MicroBrite-G Color, 100 ft cord, for a GloBrite niche or ColorVision bubbler
602166MicroBrite-G Color, 150 ft cord
602213MicroBrite-G White, 100 ft cordThe TradeGrade list names 602213 to 602215 IntelliBrite Architectural; the catalog and product page call them MicroBrite-G
602165MicroBrite-G White, 150 ft cord
602215MicroBrite-G Warm White, 100 ft cord
602167MicroBrite-G Warm White, 150 ft cord
EC-620425MicroBrite Color, 100 ft cord, sold online
EC-620429MicroBrite White, 100 ft cord, sold online
EC-620457MicroBrite Warm White, 100 ft cord, sold online
620427Combo: two MicroBrite Color lights, 100 ft, with a 300 W transformerIn the manual's parts list; not in the 2025-2026 catalog
620431Combo: two MicroBrite White lights, 100 ft, with a 300 W transformerIn the manual's parts list; not in the 2025-2026 catalog
620460Threaded adapter ring, replacement what goes wrong
602158ZInstallation tool, hand-grip style, replacement what goes wrong
620459Installation tool, the original styleIn the manual; the catalog lists 602158Z
620463Conduit seal o-ring, replacement what goes wrong
618040Adapter, MicroBrite into a GloBrite niche what goes wrong
619962Transformer, 100 W, 120 V in, 12 to 14 V out what goes wrong
619963Transformer, 300 W, 120 V in, 12 to 14 V out
618031Color Sync controller what goes wrong
86205100Wall fitting, PentairOne of the manual's compatible 1.5 in. fittings
542429Wall fitting, PentairCompatible, per the manual
542402Wall fitting, PentairCompatible, per the manual
542414Wall fitting, PentairCompatible, per the manual
542405Wall fitting, PentairCompatible, per the manual
542404Wall fitting, PentairCompatible, per the manual
SP1022Wall fitting, HaywardCompatible, per the manual
215-9170BWall fitting, WaterwayCompatible, per the manual
400-9150BWall fitting, WaterwayCompatible, per the manual
215-9890BWall fitting, WaterwayCompatible, per the manual
400-9170BWall fitting, WaterwayCompatible, per the manual
CMP25550001060Wall fitting, CMPCompatible, per the manual
CMP25522100000Wall fitting, CMPCompatible, per the manual
CMP25550000000Wall fitting, CMPCompatible, per the manual