Pentair · GloBrite
Pentair GloBrite
Pentair's small 12-volt LED light for steps and sun shelves: color or white, the plastic niche that needs no bond, and two transformer limits in one manual.

GloBrite is Pentair's small LED light for shallow water: steps, sun shelves, beach entries and spas. It runs on 12 volts and draws 15 watts, and it comes in two versions, color and white. Pentair says the white one gives the light of a 190-watt incandescent bulb.
It sits in its own plastic niche, and there's one for each kind of pool: gunite and concrete, vinyl, and fiberglass. The light can go in the wall or in the floor, pointing up, in as little as 4 inches of water. For a full-size pool light, see Pentair's IntelliBrite Architectural Series.
Each light number includes its cord: 50, 100 or 150 feet. The color light is 602054, 602055 and 602056, and the white is 602103, 602104 and 602105. The white light's manual gets this wrong: its parts list prints the color light's numbers. Go by the catalog.
Color or white
GloBrite Color has five fixed colors and seven light shows, at one brightness. Pentair's manual says it uses the same colors and shows as its IntelliBrite lights and can be synchronized with them. Pentair's catalog adds a note: for the best results with several lights, use the same model throughout and don't mix models in one installation.
GloBrite White has three brightness levels: 100, 75 and 50 percent. It leaves the factory at 100.
Color runs on IntelliTouch, EasyTouch and IntelliCenter, Pentair says, and white on those and SunTouch. A pool with no automation can run the color light from Pentair's Color Sync controller, 618031, through the Pentair Pool app. Pentair's newest lights, IntelliVibe, need their own controller, and the catalog says they don't work with GloBrite.
Working it from a wall switch
Both lights also work from an ordinary wall switch on the transformer's power. You choose a mode by switching the power off and on a set number of times.
On the color light, the count picks a show or a color:
- 1 to 7: shows. SAm, Party, Romance, Caribbean, American, California Sunset and Royal.
- 8 to 12: fixed colors. Blue, green, red, white and magenta.
- 13: Hold, which saves the moment in a show you're watching.
- 14: Recall, which brings it back.
So California Sunset is six cycles. While you're switching, the light stays dark, then shows white for a moment, then the mode. Pentair warns that the pool is dark during that time, so take care with anyone in it. If the power's been off for more than five seconds, the light comes back on in the last saved mode.
On the white light, one off-on cycle sets 100 percent. Two sets 75: the light comes on at 100 and dims after a second. Three sets 50.
The niche, and why there's no bond wire
Pentair says a GloBrite needs no bonding or grounding. The light and its plastic niche make a nonmetallic, low-voltage system, and the manuals cite the National Electrical Code's exceptions for it, in Articles 680.6 and 680.23. That holds with two conditions: a GloBrite niche, and one of the listed 100 or 300 W transformers. The manuals add that in a concrete pool, the bonded rebar already meets the code's water-bonding rule. They don't say the same for vinyl or fiberglass pools.
The three niches:
- Gunite and concrete, 620040. It comes with color rings. The catalog lists white, blue, black, gray and tan; the white light's product page leaves out black. It goes in a 15-inch length of 2-inch Schedule 40 PVC, set through the wall before the gunite goes on.
- Vinyl, 620039, with white, blue and gray rings. It goes in a 3-inch hole, behind the liner.
- Fiberglass, 620041 in white, 620093 in blue and 620094 in gray. It goes in a 2-inch hole, with a gasket in front and a washer and nut behind.
All three take 1-inch conduit at the back.
Before plastering a gunite pool, snap the plastic cover over the niche. It keeps plaster out of the light's cooling cavity. The color ring kit, 620056, includes one.
On a vinyl niche, drive the faceplate screws by hand. The manuals say not to use a power tool or overtighten them: that can damage the niche and the liner seal. The vinyl kit, 620054, has a new gasket, faceplate and screws.
Transformers, and two different limits
A GloBrite runs only from a safety isolation transformer. Pentair's are 619962 at 100 W and 619963 at 300 W, both taking 120 volts in and giving 12 to 14 out. The junction box and transformer go at least 4 inches above the ground or 8 inches above the maximum water level, whichever is higher, and at least 48 inches from the pool's edge.
How many lights on a 100 W transformer depends on which page you read. The color light's manual says no more than three GloBrite color lights in its text. Its wiring diagram says five GloBrite lights need a 100 W transformer, and the white light's manual says no more than five. Both lights draw the same 15 watts. Three keeps you inside both.
On a 300 W transformer, the total of all Pentair LED lights on it can't pass 300 watts. The color manual's diagram puts 6 to 17 GloBrite lights on one.
Keep the cable to 150 feet, in total, between the transformer and the light, in 12-gauge wire or heavier. For a longer run, Pentair says to give each light its own 100 W transformer. The white manual says to use the transformer's 13 or 14 volt tap on long runs or with several lights.
Pentair's catalog says its UL-listed underwater lights are certified for water up to 6,000 ppm salinity, so a salt pool is fine.
Never run it dry for long
The manuals give 30 seconds. Without water around it, the light shouldn't be on longer than that. Fill the pool until the light is under water before switching it on. The pool light guide compares the allowances on other makers' lights.
When it fails
There's nothing to repair inside a GloBrite. Pentair calls it a non-serviceable light: when it fails, the whole light is replaced. The cord comes with it, so a new light means a new cord through the conduit.
Before you replace it, check the two things the manuals' troubleshooting covers. If both LEDs are flashing, check the wiring at the junction box and at the switch. If the light won't come on at all, check the same connections and make sure power is reaching it.
The manuals' replacement steps:
- Switch off the circuit breaker.
- Open the junction box, disconnect the light's wires, and tie a fish tape to the old cord.
- Turn the light an eighth of a turn counterclockwise with the installation tool, and pull it and its cord out, drawing the fish tape through the conduit behind it. Work on the deck, not in the water.
- Tie the new light's cord to the fish tape and pull it back to the junction box.
- Push the new light into the niche with its locking tabs lined up, and turn it clockwise while pushing in until it stops.
- Connect black to power and white to common, and close the box. The installation steps say to leave at least 6 inches of cord in it.
The tool and a new O-ring come in the O-ring kit, 620057.
Other lights fit a GloBrite niche, too. Pentair makes MicroBrite-G versions of its MicroBrite for the GloBrite niche, sells an adapter, 618040, for the standard MicroBrite, and lists trim rings for putting an IntelliVibe Mezzo in one. Jandy's adapter puts its nicheless lights in the GloBrite gunite niche only; the Jandy nicheless page covers it. Swapping to another model means its own controller and transformer limits, so check those first.
Where you buy it
All six GloBrite light numbers are on Pentair's TradeGrade list: sold only through pool stores, builders and service companies. Pentair's warranty is one year. From a dealer and professionally installed, that covers parts and labor. Bought online, it's parts only.
Which model do you have?
The model number is on the light label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Light | Brightness | Per 100 W |
|---|---|---|---|---|
| GloBrite Color | 602054 | 5 colors, 7 shows | One level | 3 or 5 |
Note on GloBrite Color: The 50 ft cord. 602055 is 100 ft and 602056 is 150 ft. Both manuals also list a 30 ft cord, 602053, which the 2025-2026 catalog and the product page don't. | ||||
| GloBrite White | 602103 | White only | 100, 75 or 50% | 5 |
Note on GloBrite White: The 50 ft cord. 602104 is 100 ft and 602105 is 150 ft. The white light's own manual prints the color light's numbers, 602053 to 602056, in its parts list; the catalog and the product page give the white light these. | ||||
Pentair GloBrite parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The O-ring, the installation tool and O-ring lubricant. The tool fits pins into the holes in the front of the light and turns it an eighth of a turn: counterclockwise to release it, clockwise while pushing in until it stops, which is when the seal at the back of the light has closed off the conduit. Both manuals give the tool this number. If the light won't turn smoothly, pull it out a little, make sure it's seated and the niche is free of debris, and try again. $49.99 US list.
The gasket, the faceplate and its four screws for a GloBrite vinyl niche. The catalog says it comes with faceplates in white, blue and gray. The faceplate clamps the liner to the niche: line it up on the niche's tabs, pierce the liner through it, and drive the screws one at a time with a No. 2 Phillips screwdriver by hand. The manuals say never to use a power tool or overtighten them, which can damage the niche and the liner seal. $60.03 US list.
Three white faceplates, three gaskets and twelve screws: enough for three lights, where a pool has several. $60.03 US list. Gray is 602137, also $60.03, and blue 602136 at $63.65.
The sealing gasket that sits between the niche's flange and the pool wall, and the PVC washer that goes behind the wall, before the nut. $39.93 US list.
The plastic nut that holds a fiberglass or vinyl niche in its hole from behind the wall. The manuals say to tighten it by hand. $60.03 US list.
Color rings and the plastic cover for a gunite niche. The cover snaps over the front of the niche while the pool is plastered, to keep plaster out of the light's cooling cavity, and is thrown away afterward. Without one, the manuals say to mask the lens and cavity with tape. $60.03 US list.
Clips onto the four notches in the lens. Turn the solid side to 12 o'clock, so the opening is at the bottom. Pentair's sheet says to use it only on lights in the wall, not the floor. Fits color and white.
120 V in, 12 to 14 V out, rated for landscape and pool use. The white manual says to use the 13 or 14 V tap on a long cord run or with several lights on one transformer. How many GloBrite lights it carries depends on which manual you read: three color lights in the color manual's text, five in its diagram and in the white manual. The 300 W version is 619963.
Pentair's controller for its color LED lights on a pool with no automation, run from the Pentair Pool app: the same seven shows and five colors, saved favorites, schedules, and switching on at dusk. The catalog lists GloBrite Color among the lights it runs, and says it doesn't run IntelliVibe.
Pentair GloBrite manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- GloBrite color changing LED light installation and user's guide, English, Spanish and French (P/N 17302 Rev. F, 2024)manual
- GloBrite white LED light installation and user's guide (P/N 620218 Rev. G, 2023)manual
- GloBrite glare shield installation instructions (P/N 620312 Rev. A, 2015)manual
- GloBrite color product page: the color light, niches and transformers, dealer onlyspec
- GloBrite white product page: the white light, niches, transformers and glare shield, dealer onlyspec
- GloBrite brochure (PDF May 2025)spec
- Pentair Pool 2025-2026 product catalog, lighting: GloBrite on pages 154 and 155, with MicroBrite, IntelliVibe and the Color Sync controllerspec
- Pentair Pool 2025-2026 product catalog, lighting parts: GloBrite on page 410, with US list pricesdiagram
- Pentair TradeGrade SKU list (policy effective October 1, 2019)spec
- Pentair pool and spa equipment warranty informationspec
Pentair GloBrite warranty
1 year parts, Included when bought from a dealer and professionally installed labor
One year. Pentair's warranty table lists GloBrite LED lights at one year, against two for the IntelliBrite Architectural Series, MicroBrite and IntelliVibe. Bought from a store, builder or service company and professionally installed, that year covers parts and labor; bought online, including from an authorized online reseller, it's parts only. All six light numbers are on Pentair's TradeGrade list, sold only through stores, builders and service companies. Lighting also counts toward Pentair's three-year bundle warranty: a pump, a filter and at least one more eligible product, bought on one invoice from a store, builder or service company, installed at the same home and registered with the bill of sale.
Manufacturer’s termsPentair GloBrite complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
31 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 620054 | Vinyl niche replacement kit: gasket, faceplate and screws what goes wrong | $60.03 US list |
| 2 | 620055 | Fiberglass niche replacement kit: washer and gasket what goes wrong | $39.93 US list |
| 3 | 620056 | Gunite and concrete niche color ring kit: color rings and plaster cover what goes wrong | $60.03 US list |
| 4 | 620057 | O-ring kit: O-ring, installation tool and O-ring lubricant what goes wrong | $49.99 US list |
| 5 | 620058 | Nut kit, fiberglass and vinyl niche what goes wrong | $60.03 US list |
| — | 602138 | Faceplate kit, white, vinyl niche: three faceplates, three gaskets, twelve screws what goes wrong | $60.03 US list |
| — | 602137 | Faceplate kit, gray, vinyl niche: three faceplates, three gaskets, twelve screws | $60.03 US list |
| — | 602136 | Faceplate kit, blue, vinyl niche: three faceplates, three gaskets, twelve screws | $63.65 US list |
| — | 602054 | GloBrite Color, 12 V, 15 W, 50 ft cord | |
| — | 602055 | GloBrite Color, 12 V, 15 W, 100 ft cord | |
| — | 602056 | GloBrite Color, 12 V, 15 W, 150 ft cord | |
| — | 602053 | GloBrite, 12 V, 30 ft cord | In both manuals' parts lists, not in the 2025-2026 catalog |
| — | 602103 | GloBrite White, 12 V, 15 W, 50 ft cord | |
| — | 602104 | GloBrite White, 12 V, 15 W, 100 ft cord | |
| — | 602105 | GloBrite White, 12 V, 15 W, 150 ft cord | |
| — | 620040 | Niche, gunite and concrete | With white, blue, black, gray and tan rings, per the catalog; the white product page lists no black |
| — | 620039 | Niche, vinyl | With white, blue and gray rings |
| — | 620041 | Niche, fiberglass, white | |
| — | 620093 | Niche, fiberglass, blue | |
| — | 620094 | Niche, fiberglass, gray | |
| — | 619962 | Transformer, 100 W, 120 V in, 12 to 14 V out what goes wrong | |
| — | 619963 | Transformer, 300 W, 120 V in, 12 to 14 V out | |
| — | 620314 | Glare shield, color and white what goes wrong | |
| — | 618031 | Color Sync controller what goes wrong | |
| — | 618040 | Adapter, MicroBrite light into a GloBrite niche | From the catalog's MicroBrite pages |
| — | 619993 | Gunite combo: one 100 ft light, 300 W transformer and gunite niche | In both manuals, not in the 2025-2026 catalog |
| — | 619994 | Gunite combo: two 100 ft lights, 300 W transformer and two gunite niches | In both manuals, not in the 2025-2026 catalog |
| — | 620051 | Fiberglass combo: one 100 ft light, 300 W transformer and fiberglass niche | In both manuals, not in the 2025-2026 catalog |
| — | 620052 | Fiberglass combo: two 100 ft lights, 300 W transformer and two fiberglass niches | In both manuals, not in the 2025-2026 catalog |
| — | 620080 | Vinyl combo: one 100 ft light, 300 W transformer and vinyl niche | In both manuals, not in the 2025-2026 catalog |
| — | 620081 | Vinyl combo: two 100 ft lights, 300 W transformer and two vinyl niches | In both manuals, not in the 2025-2026 catalog |