Pentair · Dyna-Pro
Pentair Sta-Rite Dyna-Pro
Sta-Rite's discontinued Dyna-Pro pump: all 17 models with motor and impeller, the parts Pentair still prices, and the 2-1/2 HP impeller its catalog dropped.
Discontinued. Replaced by the SuperMax VS or IntelliPro VSF, which Pentair's Dyna-Pro page suggests. Everything on this page still applies to the units already installed.

The Dyna-Pro was Sta-Rite's self-priming pool and spa pump, from 1/2 to 2-1/2 horsepower, with its trap molded into the pump body. Pentair, which owns the Sta-Rite name, now marks it discontinued. Its page says Pentair no longer makes it, suggests asking a pool professional whether any are left in stock, and offers the SuperMax VS and the IntelliPro VSF as replacements.
Pentair's 2025-2026 catalog still lists its parts, with prices, so this page is for keeping one running. Several of them carry the same numbers as other Sta-Rite pumps: the 2 HP impeller screw is the Max-E-Pro's, and the trap basket the Max-E-Pro's and the Dura-Glas II's.
Which one you have
Pentair's page lists 17 models, with codes beginning MPE, MPEA, MPEAA and MPRA, from 1/2 to 2-1/2 horsepower. Every model the manual's motor table lists as two-speed has a Y in its code, like the MPEA6YG-207L. The table gives each one's motor, impeller and diffuser, from the manual's motor table and parts list.
The parts follow the hydraulics, not the label. The catalog names each impeller by horsepower, but its 1/2 HP impeller also fits the 3/4 HP MPEA6D-204L and MPRA6D-204L. Pentair's page shows why: the 1/2 HP MPE6C-204L and the 3/4 HP MPEA6D-204L have the same service-factor horsepower, 0.95. So find your model in the table or the impeller list rather than going by the horsepower on the motor.
What the catalog no longer lists
The 2017 manual and the 2016 parts sheet have a few parts the 2025-2026 catalog doesn't:
- The 2-1/2 HP impeller, C105-236PEA, for the MPEAA6G-208L, MPEAA6YG-208L and MPE6G-208L
- The 1/2 HP and 1 HP diffusers, C1-270PB and C1-270PC. The catalog lists only C1-270P, the diffuser for the 1-1/2 to 2-1/2 HP models.
- The blue-coated diffuser O-ring, 357098Z, and the seal plate nut, 071403
A dealer may still have them, or know the number that replaced them. Nothing I read names a replacement, so this page doesn't either.
Pentair's product page also prints one model as MPEA6YG-208L, where the manual, the 2016 sheet and the catalog all print MPEAA6YG-208L. The table keeps Pentair's spelling and notes the other.
Replacing the seal
A drip between the motor and the pump is the shaft seal, 17351-0101S, the same on every model at $41.75. The manual says running the pump dry damages it. The pump leak guide covers telling a seal leak from the others.
The manual's steps:
- Close the valves, release the pressure, and drain the pump through the plug at the bottom of the strainer pot.
- Take off the six nuts and washers holding the seal plate to the pump body, and pull the seal plate and motor away. A flat screwdriver can ease them apart.
- Take out the seven screws holding the diffuser, and lift it off.
- Take off the motor canopy without touching the capacitor terminals, and move the capacitor aside. Hold the shaft with a 1/2-inch open-end wrench on its flats.
- On 2 and 2-1/2 HP models, take out the impeller screw, a left-hand thread, and its gasket. Then unscrew the impeller counterclockwise.
- Take off the rotating half of the seal, take out the four screws holding the seal plate to the motor, lay it face down and tap out the ceramic seat. Check the slinger for damage.
Putting it back together, the manual gives a torque for every fastener:
- Motor to seal plate: 60 to 80 inch-pounds
- Impeller lock screw: 50 to 55 inch-pounds, on 2 HP, 2-1/2 HP and 3-phase models
- Diffuser screws: 10 to 14 inch-pounds
- Seal plate to pump body: 120 to 130 inch-pounds
Seat the ceramic half with a little liquid detergent on its outer edge, pressed in squarely with your thumbs; the manual uses a cardboard washer and a piece of 3/4-inch pipe if it won't go. Put a little detergent inside the rotating half and slide it on, polished carbon face out. Screwing the impeller on clockwise seats it. Don't scratch either face: the manual says a damaged one leaks.
The lid and basket
The lid comes off counterclockwise. If it sticks, tap its handles gently with a rubber mallet, and put it back hand-tight only, which the manual says keeps it from sticking.
When you put the basket back, face its large opening toward the pipe port, between the ribs. The manual says a basket in backward stops the lid fitting. Clean the lid O-ring and its groove while it's off. Don't grease the original O-ring: the manual says it has a permanent internal lubricant.
Priming and plumbing
Fill the strainer and pump with water, put the lid back, and the pump should prime. A pump below the water level primes itself when its valves open. If it won't, the manual's list is: valves open, the suction pipe's end under water, no more than 10 feet of lift, and no leaks in the suction pipe. The priming guide covers the rest.
Use at least 2-inch pipe, with a straight run of at least five times its diameter before the pump and no 90-degree elbow straight into a port. The ports take 2-inch NPT pipe inside and a Sta-Rite union collar on their 3-inch buttress thread outside. Seal threads with tape, never pipe dope, which the manual says can crack some plastics. Don't tighten past the thread stops.
Winter
Letting it freeze damages the pump and voids the warranty. Lower the water below the inlets, take off the lid, drain the pump through its two drain plugs, and cap the inlet piping. Keep the motor dry and covered, but don't wrap it in plastic. The only antifreeze the manual allows is propylene glycol: 40 percent in water protects to -50°F. Don't blow it out with compressed air; the manual calls for a low-pressure blower, under 5 psi.
Replacing it
Pentair's page names the SuperMax VS and the IntelliPro VSF. Replacing a pool pump covers what to check before you buy.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | Volts | Motor | Impeller | Diffuser |
|---|---|---|---|---|---|
| MPE6C-204L | 1/2 | 115/230 | AE100CHL | C105-236P | C1-270PB |
Note on MPE6C-204L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPE6D-205L | 3/4 | 115/230 | AE100DHL | C105-236PB | C1-270PC |
Note on MPE6D-205L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPE6E-206L | 1 | 115/230 | AE100EHL | C105-236PC | C1-270P |
| MPE6F-207L | 1-1/2 | 230 | AE100FHL | C105-236PDA | C1-270P |
Note on MPE6F-207L: Impeller screw 37337-6080 and gasket 33455-1047. | |||||
| MPE6G-208L | 2 | 230 | AE100GHL | C105-236PEA | C1-270P |
Note on MPE6G-208L: Impeller screw 37337-6080 and gasket 33455-1047. The 2025-2026 catalog lists no 2-1/2 HP impeller. | |||||
| MPEA6D-204L | 3/4 | 115/230 | AE100DLL | C105-236P | C1-270PB |
Note on MPEA6D-204L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPEA6E-205L | 1 | 115/230 | AE100ELL | C105-236PB | C1-270PC |
Note on MPEA6E-205L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPEA6F-206L | 1-1/2 | 115/230 | AE100FLL | C105-236PC | C1-270P |
| MPEA6G-207L | 2 | 230 | AE100GLL | C105-236PDA | C1-270P |
Note on MPEA6G-207L: Impeller screw 37337-6080 and gasket 33455-1047. | |||||
| MPEAA6G-208L | 2-1/2 | 230 | AE100G5LL | C105-236PEA | C1-270P |
Note on MPEAA6G-208L: Impeller screw 37337-6080 and gasket 33455-1047. The 2025-2026 catalog lists no 2-1/2 HP impeller. | |||||
| MPRA6D-204L | 3/4 | 115/230 | A100DLL | C105-236P | C1-270PB |
Note on MPRA6D-204L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPRA6E-205L | 1 | 115/230 | A100ELL | C105-236PB | C1-270PC |
Note on MPRA6E-205L: The 2025-2026 catalog lists no diffuser for it. | |||||
| MPRA6F-206L | 1-1/2 | 115/230 | A100FLL | C105-236PC | C1-270P |
| MPRA6G-207L | 2 | 230 | A100GLL | C105-236PDA | C1-270P |
Note on MPRA6G-207L: Impeller screw 37337-6080 and gasket 33455-1047. | |||||
| MPEA6YG-207L | 2 | 230, 2-speed | AE100GLL-Y | C105-236PDA | C1-270P |
Note on MPEA6YG-207L: Impeller screw 37337-6080 and gasket 33455-1047. | |||||
| MPEA6YG-208L | 2-1/2 | 230, 2-speed | AE100G5LL-Y | C105-236PEA | C1-270P |
Note on MPEA6YG-208L: Pentair's product page prints it MPEA6YG-208L; the manual, the 2016 sheet and the catalog print MPEAA6YG-208L. Impeller screw 37337-6080 and gasket 33455-1047. The 2025-2026 catalog lists no 2-1/2 HP impeller. | |||||
| MPRA6YF-206L | 1-1/2 | 230, 2-speed | A100FLL-Y | C105-236PC | C1-270P |
Pentair Sta-Rite Dyna-Pro parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The same seal on every model. The manual says running the pump dry damages it and makes the pump leak. Keep the white ceramic seat clean and free of grease: wet its outer edge with a little liquid detergent and press it in squarely with your thumbs, and don't scratch either face. $41.75 US list.
The seal between the seal plate and the pump body, held by six nuts. Tighten them to 120 to 130 inch-pounds when the pump goes back together. The manual prints it U9-373. $14.68 US list.
The manual's troubleshooting says to inspect it and replace it if it's damaged. Don't lubricate the original: it carries a permanent internal lubricant. A replacement without one may need a silicone-based lubricant. $29.77 US list.
Turn it counterclockwise to take it off, and tap the handles gently with a rubber mallet if it sticks. Put it back hand-tight only: the manual says that's what keeps it from sticking. $112.32 US list.
Put it back with its large opening facing the pipe port, between the ribs. The manual says a basket in backward stops the lid fitting. Cleaning it is the only routine maintenance. $22.05 US list.
The whole front of the pump, with the trap molded in. The manual warns that letting the pump freeze damages it, and that pipe dope can crack some plastics. $436.79 US list.
For the MPEA6G-207L, MPE6F-207L, MPEA6YG-207L, MPE6YF-207L and MPRA6G-207. Every catalog impeller is $75.84 US list; the table above has each model's. On 2 and 2-1/2 HP models, take out the impeller screw first, a left-hand thread, and fit a new gasket if the old one is cracked.
A left-hand thread. Tighten it to 50 to 55 inch-pounds, with its gasket, 33455-1047, under it. $30.83 US list.
If you are doing the job anyway
The seal plate comes off the pump body for any seal job, so its cord ring and the diffuser O-ring are in your hands too. Numbers carry the Z the 2025-2026 catalog prints where it lists the part.
Shaft seal job
The seal, the cord ring between the seal plate and the body, and the diffuser O-ring are the three seals the job uncovers: $65.11 at US list for all three.
- Shaft seal17351-0101S
- Seal plate cord ringU9-373Z
- U9-374ZU9-374Z
Pentair Sta-Rite Dyna-Pro manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Dyna-Pro self-priming pool and spa pump installation and user's guide (P/N S771 Rev. D, 2017)manual
- Dyna-Pro product page: the discontinued notice and every modelspec
- Pentair Pool 2025-2026 product catalog, pump parts: the Dyna-Pro on page 462, with US list pricesdiagram
- Dyna-Pro and Dyna-Pro E replacement parts, the older catalog page with the motor chart (PDF 2016)diagram
- Pentair pool and spa equipment warranty informationspec
Pentair Sta-Rite Dyna-Pro warranty
One year on Pentair's row for single-speed pumps, or two on its row for single-phase TEFC Super Duty pumps
Pentair's warranty table doesn't name the Dyna-Pro. It gives single-speed and booster pumps one year and single-phase TEFC Super Duty pumps two, without saying which row a Dyna-Pro falls in. The manual adds that letting the pump freeze damages it and voids the warranty. The pump is discontinued, so the warranty only matters on one installed from a dealer's remaining stock.
Manufacturer’s termsPentair Sta-Rite Dyna-Pro complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
54 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | A100DLL | Motor, 3/4 HP, 115/230 V, MPRA6D-204L | The manual's motor table |
| 1 | A100ELL | Motor, 1 HP, 115/230 V, MPRA6E-205L | |
| 1 | A100FLL | Motor, 1-1/2 HP, 115/230 V, MPRA6F-206L | |
| 1 | AE100DLL | Motor, 3/4 HP, 115/230 V, MPEA6D-204L | |
| 1 | AE100ELL | Motor, 1 HP, 115/230 V, MPEA6E-205L | |
| 1 | AE100FLL | Motor, 1-1/2 HP, 115/230 V, MPEA6F-206L | |
| 1 | AE100CHL | Motor, 1/2 HP, 115/230 V, MPE6C-204L | |
| 1 | AE100DHL | Motor, 3/4 HP, 115/230 V, MPE6D-205L | |
| 1 | AE100EHL | Motor, 1 HP, 115/230 V, MPE6E-206L | |
| 1 | A100GLL | Motor, 2 HP, 230 V, MPRA6G-207L | |
| 1 | AE100GLL | Motor, 2 HP, 230 V, MPEA6G-207L | |
| 1 | AE100G5LL | Motor, 2-1/2 HP, 230 V, MPEAA6G-208L | |
| 1 | AE100FHL | Motor, 1-1/2 HP, 230 V, MPE6F-207L | |
| 1 | AE100GHL | Motor, 2 HP, 230 V, MPE6G-208L | |
| 1 | A100FLL-Y | Motor, 1-1/2 HP, two-speed, MPRA6YF-206L | |
| 1 | AE100GLL-Y | Motor, 2 HP, two-speed, MPEA6YG-207L | The 2016 sheet gives it to the MPE6YF-207L too |
| 1 | AE100G5LL-Y | Motor, 2-1/2 HP, two-speed, MPEAA6YG-208L | And the MPE6YG-208L |
| 2 | U30-692SS | Screw, #10-32 x 1/2 in. | $3.40 US list |
| 3 | U17-568 | Bonding lug | Price on request |
| 4 | 17351-0009 | Slinger | $3.01 US list |
| 5 | C3-184P | Seal plate | $187.85 US list |
| 6 | U9-373Z | Seal plate cord ring what goes wrong | $14.68 US list. The manual prints U9-373 |
| 7 | 17351-0101S | Shaft seal what goes wrong | $41.75 US list |
| 8 | C105-236P | Impeller, 1/2 HP models: MPEA6D-204L, MPE6C-204L, MPRA6D-204L | $75.84 US list |
| 8 | C105-236PB | Impeller, 1 HP models: MPEA6E-205L, MPE6D-205L, MPRA6E-205L, MPRA6E-147L, MPRA6E-147LC | $75.84 US list |
| 8 | C105-236PC | Impeller, 1-1/2 HP models: MPEA6F-206L, MPE6E-206L, MPRA6F-206L, MPRA6YF-206L | $75.84 US list |
| 8 | C105-236PDA | Impeller, 2 HP models: MPEA6G-207L, MPE6F-207L, MPEA6YG-207L, MPE6YF-207L, MPRA6G-207 what goes wrong | $75.84 US list |
| 8 | C105-236PEA | Impeller, 2-1/2 HP models: MPEAA6G-208L, MPA6G-208L, MPEAA6YG-208L, MPE6G-208L | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 8A | 33455-1047 | Gasket, impeller, 2 and 2-1/2 HP models | Price on request |
| 8B | 37337-6080 | Impeller lock screw, 2 and 2-1/2 HP models what goes wrong | $30.83 US list |
| 9 | C1-270PB | Diffuser, 1/2 HP models | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 9 | C1-270PC | Diffuser, 1 HP models | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 9 | C1-270P | Diffuser, 1-1/2, 2 and 2-1/2 HP models | $46.99 US list |
| 10 | U9-374Z | Diffuser O-ring | $8.68 US list. The manual prints U9-374 |
| 10 | 357098Z | Diffuser O-ring, blue coating | The manual and the 2016 sheet |
| 11 | C76-71P | Tank and trap body, only what goes wrong | $436.79 US list |
| 12 | 17307-0111S | Lid and locking ring assembly what goes wrong | $112.32 US list |
| 13 | 35505-1440Z | Trap cover O-ring what goes wrong | $29.77 US list. The manual prints 35505-1440 |
| 14 | C8-58PZ | Trap basket what goes wrong | $22.05 US list. The manual prints C8-58P |
| 15A | U178-920PZ | Drain plug | Two. $8.07 US list |
| 15B | U30-919SS | Mounting screw, 5/16-14 x 5/8 in. | Two. $7.00 US list |
| 16 | C4-77P | Base, plastic | $79.63 US list |
| 17 | C35-45 | Motor pad, for the plastic base | $7.21 US list |
| 18 | U30-542SSZ | Screw, #8-32 x 7/8 in. round head | Seven, for the diffuser. $3.61 US list |
| 19 | U43-21SSZ | Lock washer, #8 external tooth | Seven. $2.91 US list |
| 20 | U43-62SSZ | Flat washer, 3/8 in. | Six. $2.75 US list |
| 21 | U43-12SSZ | Lock washer, 3/8 in. | Six. $4.55 US list |
| 22 | 071403 | Nut, 3/8-16 hex | Six, seal plate to pump body. The manual and the 2016 sheet |
| 22 | U30-75SS | Cap screw, 3/8-16 x 1-1/4 in. hex, LS suffix models | Two. $4.81 US list; the catalog numbers it item 22 |
| 23 | U30-74SSZ | Cap screw, 3/8-16 x 1 in. hex | Four. $7.00 US list; the manual numbers it item 24 |
| — | PKG 188Z | Union kit, 2 in. slip, two halves | With U11-200P collars, U9-362Z O-rings and U11-196P adapters |
| — | PKG 189 | Union kit, 2 in. NPT, two halves | With U11-199P NPT adapters |
| — | 77703-0105 | Union kit, 1.5 and 2 in. union halves | The manual's order number |
| — | 38405-4094 | Union collar | Fits the 3 in. buttress thread on the ports, per the manual |