Pentair · Dura-Glas
Pentair Sta-Rite Dura-Glas and Max-E-Glas
Sta-Rite's discontinued Dura-Glas and Max-E-Glas pumps: 91 models across two series, the parts Pentair still lists, and the two clamp parts its manual swaps.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Dura-Glas and the Max-E-Glas were Sta-Rite's self-priming pool pumps, single-speed and two-speed, from 1/2 to 3 horsepower. Pentair, which owns the Sta-Rite name, no longer lists either one. There's no product page, and its 2025-2026 catalog names them only as pumps two of its strainer traps fit. Neither Pentair nor the manuals say when they stopped.
This page is for keeping one running: which one you have, the parts, and the manuals' procedures. Sta-Rite's manuals are the source, and Pentair no longer hosts them, so the links go to copies on dealers' and builders' sites.
Which one you have
The model number is on the pump's nameplate. There are two series, and the trap tells them apart.
Series II has its trap molded into the pump body. Sta-Rite's 2003 manual puts the Dura-Glas II under model numbers starting P4R and the Max-E-Glas II under P4E, from 3/4 to 3 horsepower.
Series I has a separate trap bolted to the front of the pump, or none. Its 2010 manual covers both names together, as series PE, PEA, P2R and P2RA, and doesn't say which series carries which name. The manual's rule for the trap:
- PE5, PE52, P2R5, P2RA5 and P2R52 models came with the 5-inch trap, Pkg. 115.
- PE6 and P2RA6 models came with the 6-inch trap, Pkg. 161.
- PEX, PEAX, P2RX and P2RAX models came without one. The manual says these need an NSF-listed hair and lint strainer to meet NSF Standard 50.
The manual doesn't place the PEA5, PEA6 and P2FA models in that rule.
The table lists all 91 models in the two manuals, with each one's motor, impeller and diffuser. The 38 series II models come first, Dura-Glas II then Max-E-Glas II, followed by the 53 series I.
What Pentair still lists
Many series II parts carry the same numbers as the Sta-Rite Max-E-Pro's, and Pentair's 2025-2026 catalog still prices them, most on the Max-E-Pro's pages. At US list:
- Seal plate kit, C203-194P: $267.62, with the o-ring and shaft seal
- Clamp, C19-37AZ: $167.19, and its knob, WC36-22Z, $20.34
- Diffuser, C1-271PZ: $51.17
- Seal plate o-ring, U9-228AZ: $15.63, on both series
- Basket, C8-58PZ: $22.05
- Diffuser o-ring, U9-374Z: $8.68
- Impeller screw, 37337-6080: $30.83
The series II impeller numbers are in the Max-E-Pro's charts too.
Both series I traps are still listed on the catalog's trap page. The 5-inch Pkg. 115 is $230.30 complete, and its lid, o-ring, basket, body and gasket are all sold separately. The 6-inch Pkg. 161 has its lid, o-ring, basket and gasket listed, but not its body.
Not in the current catalog: the series II trap cover, C3-185P, its o-ring, U9-375, and the pump body, C176-59P; the series I seal plate, C203-193P, its shaft seal, 17304-0100S, and its pump body, C176-47P1; any of the shaft seals the series II manuals print; and the Parts-Pak overhaul kits. A dealer may still have stock, or know the number that replaced it. Nothing I read names a replacement for any of them, so this page doesn't either.
Two parts the 2003 manual mixes up
C19-37A is the clamp, and WC36-22 is its knob. Sta-Rite's 2003 manual has four parts lists, and three of them, for the Max-E-Glas II, the single-phase Dura-Glas II and the 200/400-volt Dura-Glas II, print the two the other way round. The three-phase Dura-Glas II list, the 2010 manual and Pentair's current catalog all agree. So do the prices: $167.19 for the clamp against $20.34 for the knob.
A diffuser number that can't be right
The single-phase Dura-Glas II list prints C1-271P1 as the diffuser, then adds a footnote that four models, the P4R6E, P4RA6E, P4RA6F and P4RA6YF, use C1-271P1. One of the two is a misprint. On every other series II list, C1-271P1 goes with the smaller impellers and C1-271P with the larger ones. The table shows the six models this affects as printed, and the diffuser screws change with it: U30-542SS with the C1-271P1, U30-922SS with the C1-271P. Check the one on your pump before ordering.
The shaft seal
Water dripping between the motor and the pump is the shaft seal. It carries a different number in each manual: 17304-0100S on series I, 37400-0027S on series II in the 2003 revision, and U109-358SS in the 1999 one. The Max-E-Glas II models ending LV take a Viton seal, 37400-0028S. Pentair's catalog lists none of them, but it does still list the series II seal plate kit, C203-194P, which includes the seal. The pump leak guide covers telling a seal leak from the others.
The manuals' steps for taking the seal out:
- Close the valves, open the vents to release the pressure, and drain the pump through its plugs.
- Take off the trap cover and the clamp, and pull the motor and seal plate away from the pump body.
- Take out the five screws holding the diffuser to the seal plate.
- Take off the motor canopy, short the capacitor, and hold the shaft with a 7/16-inch open-end wrench on its flats.
- If there's an impeller screw, take it out first. It's a left-hand thread, so it turns clockwise to come out. Then unscrew the impeller counterclockwise.
- Take out the four screws holding the seal plate to the motor, lay it face down, and tap the ceramic seat out.
And for putting the new one in:
- Clean the seal cavity. Wet the outer edge of the ceramic seat's rubber with a little liquid detergent, and press it in squarely with your fingers. If it won't seat, a cardboard washer over the face and a piece of 3/4-inch pipe will press it.
- Bolt the seal plate back on at 60 to 80 inch-pounds.
- Put a little detergent inside the rotating half and slide it on, polished face last, until its drive ring meets the shaft shoulder.
- Screw the impeller on clockwise, which seats the seal. Refit the impeller screw and its gasket, turning counterclockwise.
- Screw the diffuser on at 10 to 14 inch-pounds, seat the clamp, and prime the pump.
Don't scratch either polished face. The manuals say a damaged face leaks.
The trap lid
Tighten it by hand, never with a wrench. The manuals say so in capitals, more than once, and give it lugs for a lever if it sticks. The 2010 manual names Sta-Rite's U79-11 lid wrench for a lid that's been overtightened. The only time it goes on harder is for a pressure test: 30 foot-pounds, under 25 psi and 100°F, for no more than 24 hours, then back to hand tight.
Don't grease the original lid o-ring: the manuals say it carries a permanent internal lubricant. A replacement without one may need a silicone-based lubricant.
The basket is the only routine maintenance the manuals give. Stop the pump, close the valves and release the pressure, then clean the basket, the lid o-ring and the o-ring's groove.
Priming, and running it dry
Never run it dry. The manuals say that can damage the seal and cause leaking. Fill the trap and pump with water before starting it. A pump below the water level primes itself when its valves open.
The manuals' limits on how far it can lift water differ by series. Series I loses performance above 15 feet and won't pump above 25. Series II gives 10 and 20. Either way, the fix is moving the pump closer to the water and checking the suction pipe is big enough. The priming guide covers the rest.
Plumbing it
Use Teflon tape or Plasto-Joint Stik on threaded connections, never pipe dope: the manuals say it causes stress cracking in the pump. The ports have molded-in thread stops, so don't screw past them. Use at least 1-1/2-inch pipe with the 5-inch trap, and 2-inch with the 6-inch trap and on series II. Support both pipes on their own, near the pump.
Winter
Letting it freeze damages the pump and voids the warranty. Drain it through the plugs on the pump and trap, keep the motor dry and covered, and don't wrap it in plastic, which traps condensation. The only antifreeze the manuals allow is propylene glycol: 40 percent in water protects to -50°F.
Don't blow it out with compressed air. The manuals warn that can make parts explode, and call for a low-pressure blower, under 5 psi.
Replacing it
When it's time, check the base height first. Jandy says its FloPro needs a separately ordered base to replace a Dura-Glas, and Hayward sells a riser base for the TriStar VS 800 for the same job. Replacing a pool pump covers the rest.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | Volts | Motor | Impeller | Diffuser |
|---|---|---|---|---|---|
| P4RA6E-186L | 1 | 115/230 | A100ELL | C105-238P | C1-271P1 |
| P4R6E-187L | 1 | 115/230 | A100EHL | C105-238PB | C1-271P1 |
| P4RA6F-187L | 1-1/2 | 115/230 | A100FLL | C105-238PB | C1-271P1 |
| P4R6F-188L | 1-1/2 | 230 | A100FHL | C105-238PDBA | C1-271P1 |
Note on P4R6F-188L: The diffuser is as the list prints it, which may be a misprint. | |||||
| P4RAA6F-198L | 1-3/4 | 230 | A100F5LL | C105-238PDCA | C1-271P1 |
Note on P4RAA6F-198L: Impeller screw 37337-6080. The diffuser is as the list prints it, which may be a misprint. | |||||
| P4R6G-189L | 2 | 230 | AE100GHL | C105-238PEBA | C1-271P1 |
Note on P4R6G-189L: The diffuser is as the list prints it, which may be a misprint. | |||||
| P4RA6G-188L | 2 | 230 | A100GHL | C105-238PDBA | C1-271P1 |
Note on P4RA6G-188L: The diffuser is as the list prints it, which may be a misprint. | |||||
| P4RAA6G-189L | 2-1/2 | 230 | AE100G5LL | C105-238PEBA | C1-271P1 |
Note on P4RAA6G-189L: The diffuser is as the list prints it, which may be a misprint. | |||||
| P4RA6YF-187L | 1-1/2 | 230, 2-speed | A100FLL-Y | C105-238PB | C1-271P1 |
Note on P4RA6YF-187L: Two-speed. | |||||
| P4RA6YG-188L | 2 | 230, 2-speed | AE100GLL-Y | C105-238PDBA | C1-271P1 |
Note on P4RA6YG-188L: Two-speed. The diffuser is as the list prints it, which may be a misprint. | |||||
| P4R6D3-186 | 3/4 | 3-ph 208-230/460 | AP100DH | C105-238PA | C1-271P1 |
| P4R6E3-187 | 1 | 3-ph 208-230/460 | AP100EH | C105-238PBA | C1-271P1 |
Note on P4R6E3-187: Impeller screw assembly 17301-0152. | |||||
| P4R6F3-188 | 1-1/2 | 3-ph 208-230/460 | AP100FH | C105-238PDBA | C1-271P |
| P4R6G3-189 | 2 | 3-ph 208-230/460 | AP100GH | C105-238PEBA | C1-271P |
| P4R6H3-190 | 3 | 3-ph 230/460 | AP100HL | C105-238PLA | C1-271P |
Note on P4R6H3-190: Base C104-79P with motor pad C35-44. No bonding lug assembly. | |||||
| P4R62D3-186L | 3/4 | 3-ph 200/400 | AP100DH2 | C105-238PA | C1-271P1 |
| P4R62E3-187 | 1 | 3-ph 200/400 | AP100EH2 | C105-238PBA | C1-271P1 |
| P4R62F3-188 | 1-1/2 | 3-ph 200/400 | AP100FH2 | C105-238PDBA | C1-271P |
| P4R62G3-189 | 2 | 3-ph 200/400 | AP100GH2 | C105-238PEBA | C1-271P |
| P4E6D-186L | 3/4 | 115/230 | AE100DHL | C105-238P | C1-271P1 |
Note on P4E6D-186L: P4E6D-186LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4E6E-187L | 1 | 115/230 | AE100EHL | C105-238PB | C1-271P1 |
Note on P4E6E-187L: P4E6E-187LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4EA6E-186L | 1 | 115/230 | AE100ELL | C105-238P | C1-271P1 |
| P4EA6F-187L | 1-1/2 | 115/230 | AE100FLL | C105-238PB | C1-271P1 |
| P4E6F-188L | 1-1/2 | 230 | AE100FHL | C105-238PDBA | C1-271P |
Note on P4E6F-188L: Impeller screw 37337-6080. P4E6F-188LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4EAA6F-198L | 1-3/4 | 230 | AE100F5LL | C105-238PDCA | C1-271P |
Note on P4EAA6F-198L: Impeller screw 37337-6080. | |||||
| P4E6G-189L | 2 | 230 | AE100GHL | C105-238PEBA | C1-271P |
Note on P4E6G-189L: Impeller screw 37337-6080. P4E6G-189LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4EA6G-188L | 2 | 230 | AE100GLL | C105-238PDBA | C1-271P |
Note on P4EA6G-188L: Impeller screw 37337-6080. P4EA6G-188LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4EAA6G-189L | 2-1/2 | 230 | AE100G5LL | C105-238PEBA | C1-271P |
Note on P4EAA6G-189L: Impeller screw 37337-6080. | |||||
| P4E6H-190L | 3 | 230 | AE100HLL | C105-238PLA | C1-271P |
Note on P4E6H-190L: Impeller screw 37337-6080. Base C104-79P with motor pad C35-44. P4E6H-190LV is the same with a Viton shaft seal, 37400-0028S. | |||||
| P4E62D-186L | 3/4 | 100/200 | AE100DH2 | C105-238P | C1-271P1 |
| P4E62E-187L | 1 | 200 | AE100EH2 | C105-238PB | C1-271P1 |
| P4E62F-188L | 1-1/2 | 200 | AE100FH2 | C105-238PDBA | C1-271P |
Note on P4E62F-188L: Impeller screw 37337-6080. | |||||
| P4E62G-189L | 2 | 200 | AE100GH2 | C105-238PEBA | C1-271P |
Note on P4E62G-189L: Impeller screw 37337-6080. | |||||
| P4E62H-190L | 3 | 200 | AE100GHL2 | C105-238PLA | C1-271P |
Note on P4E62H-190L: Impeller screw 37337-6080. Base C104-79P with motor pad C35-44. | |||||
| P4E6G36-189 | 2 | 3-ph 575 | 62003-2087 | C105-238PEBA | C1-271P |
Note on P4E6G36-189: Impeller screw 37337-6080. | |||||
| P4E6SSG36-189 | 2 | 3-ph 575 | 62003-2087 | C105-238PEBA | C1-271PSS |
Note on P4E6SSG36-189: Impeller screw 37337-6080. Seal plate C203-194SS. | |||||
| P4E6H36-190 | 3 | 3-ph 575 | 62001-1021 | C105-238PLA | C1-271P |
Note on P4E6H36-190: Impeller screw 37337-6080. | |||||
| P4E6SSH36-190 | 3 | 3-ph 575 | 62001-1021 | C105-238PLA | C1-271PSS |
Note on P4E6SSH36-190: Impeller screw 37337-6080. Seal plate C203-194SS. | |||||
| PE5C-180L | 1/2 | 115/230 | AE100CHL | C105-92PS | C1-216P |
| PE52C-180L | 1/2 | 100/200 | AE100CH2 | C105-92PS | C1-216P |
| P2R5C-180L | 1/2 | 115/230 | A100CHL | C105-92PS | C1-216P |
| P2RA5C-179L | 1/2 | 115/230 | A100CLL | C105-92PR | C1-217P1 |
| PE52D-181L | 3/4 | 100/200 | AE100DH2 | C105-138PEB | C1-200PA |
| PE5D-181L | 3/4 | 115/230 | AE100DHL | C105-138PEB | C1-200PA |
| PEA5D-180L | 3/4 | 115/230 | AE100DLL | C105-92PS | C1-216P |
| PEAXSSD-180 | 3/4 | 115/230 | AE100DLL | C105-92PSC | C1-216PB |
| P2R5D-181L | 3/4 | 115/230 | A100DHL | C105-138PEB | C1-200PA |
| P2RA5D-180L | 3/4 | 115/230 | A100DLL | C105-92PS | C1-216P |
| 71532 | 3/4 | 115/230 | A100DLL | C105-92PS | C1-216P |
| PE52E-182L | 1 | 100/200 | AE100EH2 | C105-137PEB | C1-200PA |
| PE5E-182L | 1 | 115/230 | AE100EHL | C105-137PEB | C1-200PA |
| PEA5E-181L | 1 | 115/230 | AE100ELL | C105-138PEB | C1-200PA |
| PEAXSSE-181 | 1 | 115/230 | AE100ELL | C105-138PEBB | C1-200PAB |
| P2FA5E-180L | 1 | 115/230 | A100ESLL | C105-92PS | C1-216P |
| P2R5E-182L | 1 | 115/230 | A100EHL | C105-137PEB | C1-200PA |
| P2RA5E-181L | 1 | 115/230 | A100ELL | C105-138PEB | C1-200PA |
| 71808 | 1 | 115/230 | A100ELL | C105-138PEB | C1-200PA |
| PEA5F-182L | 1-1/2 | 115/230 | AE100FLL | C105-137PEB | C1-200PA |
| PEA6F-182L | 1-1/2 | 115/230 | AE100FLL | C105-137PEB | C1-200PA |
| PEAXSSF-182 | 1-1/2 | 115/230 | AE100FLL | C105-137PEB1 | C1-200PAB |
| P2FA5F-181L | 1-1/2 | 115/230 | A100FSLL | C105-138PEB | C1-200PA |
| P2RAXF-182LS | 1-1/2 | 115/230 | A100FLL | C105-137PEB | C1-200PA |
| PE52F-183L | 1-1/2 | 200 | AE100FH2 | C105-137PDBA | C1-200PA |
| PEAXSSG-183 | 2 | 230 | AE100GLL | C105-137PDB1A | C1-200PAB |
Note on PEAXSSG-183: One impeller screw, C30-47. | |||||
| P2RA6G-183L | 2 | 230 | A100GLL | C105-137PDBA | C1-200PA |
| P2RAXG-183L | 2 | 230 | A100GLL | C105-137PDBA | C1-200PA |
Note on P2RAXG-183L: P2RAXG-183LS is the same. | |||||
| PEAAXSSG-184 | 2-1/2 | 230 | AE100G5LL | C105-137PD1A | C1-200PAB |
Note on PEAAXSSG-184: One impeller screw, C30-47. | |||||
| PE6H-185L | 3 | 230 | AE100HLL | C105-137PKBA | C1-259P |
Note on PE6H-185L: PE6H-185LC is the same. One impeller screw, C30-12. | |||||
| PEXYD-194L | 3/4 and 1/8 | 115 | AE100ELL-Y | C105-138PEBA | C1-200PA |
| PEAXYE-181L | 1 and 1/6 | 230 | 62003-2001 | C105-138PEB | C1-200PA |
| P2RA5YE-181L | 1 and 1/6 | 230 | A100ELL-Y | C105-138PEB | C1-200PA |
Note on P2RA5YE-181L: Two-speed. P2RA5YE-181LC is the same. | |||||
| P2RA5YE-194L | 1 and 1/6 | 115 | AE100SLL-Y | C105-138PEB | C1-200PA |
| P2RA5YF-182L | 1-1/2 and 1/4 | 230 | A100FLL-Y | C105-137PEBA | C1-200PA |
Note on P2RA5YF-182L: Two-speed. One impeller screw, C30-12. | |||||
| P2RA6YF-182L | 1-1/2 and 1/4 | 230 | A100FSLL-Y | C105-137PEBA | C1-200PA |
| P2RA5YF-196L | 1-1/2 and 1/4 | 115 | A100FSLL-Y | C105-137PEBA | C1-200PA |
| PEAXYG-183L | 2 and 1/3 | 230 | AE100GLL-Y | C105-138PDBA | C1-200PA |
| P2RA5YG-183L | 2 and 1/3 | 230 | AE100GLL-Y | C105-137PDBA | C1-200PA |
Note on P2RA5YG-183L: Two-speed. One impeller screw, C30-12. | |||||
| PEAXYG-183LS | 2 and 1/3 | 230 | AE100GLL-Y | C105-138PDBA | C1-200PA |
| P2RA5C3-179 | 1/2 | 3-ph 208-230/460 | AP100CL | C105-92PRA | C1-217P |
| P2R5D3-181 | 3/4 | 3-ph 208-230/460 | AP100DH | C105-138PEBA | C1-200PA |
| P2R52D3-181 | 3/4 | 3-ph 200/400 | AP100DH2 | C105-138PEBA | C1-200PA |
| P2R5E3-182 | 1 | 3-ph 208-230/460 | AP100EH | C105-137PEBA | C1-200PA |
| P2R52E3-181 | 1 | 3-ph 200/400 | AP100EH2 | C105-137PEBA | C1-200PA |
| P2R5F3-183 | 1-1/2 | 3-ph 208-230/460 | AP100FH | C105-137PDBA | C1-200PA |
| P2R52F3-183 | 1-1/2 | 3-ph 200/400 | AP100FH2 | C105-137PDBA | C1-200PA |
| P2RA5F36-182 | 1-1/2 | 3-ph 575 | 62001-1019 | C105-137PEBA | C1-200PA |
| P2R5G3-184 | 2 | 3-ph 230/460 | AP100GH | C105-137PDA | C1-200PA |
| P2R52G3-184 | 2 | 3-ph 200/400 | AP100GH2 | C105-137PDA | C1-200PA |
| PE5G36-184 | 2 | 3-ph 575 | 62003-2087 | C105-137PDBA | C1-200PA |
| P2RA5G36-183 | 2 | 3-ph 575 | 62003-2087 | C105-137PDBA | C1-200PA |
| PE6H3-185 | 3 | 3-ph 200-230/460 | AP100HL | C105-137PKBA | C1-200PA |
Pentair Sta-Rite Dura-Glas and Max-E-Glas parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The seal plate with its o-ring and the shaft seal, the one seal Pentair still lists with a price for series II: $267.62 US list, on its Max-E-Pro pages. The shaft seal alone carries three numbers across the manuals: 37400-0027S in the 2003 revision, U109-358SS in the 1999 one, and 37400-0028S, in Viton, on the Max-E-Glas II models ending LV. None of them is in Pentair's current catalog. The manuals say running the pump dry can damage the seal and cause leaking.
The 2010 manual's seal for every series I model. The seal plate it presses into is C203-193P. Neither number is in Pentair's current catalog. When you fit it, keep the ceramic seat clean and free of grease: the manual uses a little liquid detergent on the seat's o-ring and inside the rotating half, and a nick or scratch on either polished face makes the seal leak.
The large o-ring between the seal plate and the pump body, inside the clamp. The manuals print it U9-228A. $15.63 US list. It comes in the series II seal plate kit, C203-194P.
The band that holds the motor and seal plate to the pump body, tightened by its knob, WC36-22Z at $20.34. Never loosen or tighten it while the pump is running or under pressure: the manual warns it can blow off. The knob can sit anywhere around the body. If you move it after assembly, tighten it while tapping around the clamp to help it seal, and don't move the clamp while the pump is full of water. $167.19 US list.
The basket in the molded-in trap. Cleaning it is the only routine maintenance the manuals ask for: debris in it chokes the flow through the pump. Make sure every hole is clear, and clean the lid o-ring and its groove before the lid goes back on. $22.05 US list.
The o-ring under the trap lid, C3-185P. Neither number is in Pentair's current catalog. Don't lubricate the original: the manuals say it carries a permanent internal lubricant. A replacement without one may need a silicone-based lubricant.
The lid for the Pkg. 115 trap, at $92.61 US list. Its o-ring is U9-229Z at $21.54 and its basket C108-33PZ at $20.43. The whole trap is $230.30. The manual prints the lid and basket without the Z.
The lid for the Pkg. 161 trap, at $110.79 US list. Its o-ring is 16920-0012 at $32.52 and its basket 16920-0017Z at $46.99. The catalog doesn't list this trap's body, C153-58P.
The gasket between a bolt-on trap and the pump, the same on both traps. The manual's troubleshooting says to replace it if it's defective, under suction leaks and lost prime. $14.37 US list.
Sta-Rite's lid wrench, which the 2010 manual names for a lid that's been overtightened or has set. Both manuals say to use a lever between the lugs on the lid if you need one, and to tighten the lid by hand only, never with a wrench. Not in Pentair's current catalog.
If you are doing the job anyway
The seal plate comes off the motor for any seal job, so its o-rings are already in your hands. Numbers carry the Z the 2025-2026 catalog prints where it lists the part; the manuals leave it off.
Shaft seal, series II
The seal plate kit carries the shaft seal and the seal plate o-ring. The diffuser comes off the seal plate on the way to the seal, and its o-ring is the other seal you'll be holding.
- Seal plate kit, series IIC203-194P
- U9-374ZU9-374Z
Shaft seal, series I
The seal, the seal plate o-ring and the diffuser o-ring are the three seals the job uncovers. Only the seal plate o-ring is still in Pentair's catalog.
- Shaft seal, series I17304-0100S
- Seal plate o-ring, both seriesU9-228AZ
- U9-226U9-226
Trap lid, 5 in. trap
The lid and its o-ring seal together, and the two cost $114.15 at US list against $230.30 for the complete trap.
- Trap cover, 5 in. trap, series IC3-139P1Z
- U9-229ZU9-229Z
Pentair Sta-Rite Dura-Glas and Max-E-Glas manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Dura-Glas and Max-E-Glas pumps with trap, owner's manual, series PE, PEA, P2R and P2RA (S413 Rev. A, 2010). A dealer's copy: Pentair no longer hosts itmanual
- Max-E-Glas II and Dura-Glas II pumps with integral trap, owner's manual (S454, revised July 2003). A pool builder's copymanual
- The same series II manual's May 1999 revision, with the older shaft seal and slinger numbersmanual
- Pentair Pool 2025-2026 product catalog, pump parts: the Max-E-Pro pages and the 5 in. and 6 in. trap page, with US list prices for the parts these pumps sharediagram
- Pentair Pool 2025-2026 product catalog, pumps: the hair and lint strainer packages Pentair lists for the Dura-Glas and Max-E-Glasspec
Pentair Sta-Rite Dura-Glas and Max-E-Glas warranty
One year from installation, under Sta-Rite's own warranty
Sta-Rite's 2003 warranty covered its pumps for one year from installation, or two with an A.O. Smith two-compartment motor when the pump wasn't sold as part of a systems package. Traps and in-line strainers got one year. Claims went through the installing dealer, and the owner paid labor and shipping. The manuals add that letting the pump freeze voids it. Pentair's current warranty page doesn't list either pump, and any Dura-Glas or Max-E-Glas still running is past that year.
Manufacturer’s termsPentair Sta-Rite Dura-Glas and Max-E-Glas complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
163 parts
| No. | Part | Description | Note |
|---|---|---|---|
| I-2, II-2 | U30-692SS | Screw, #10-32 x 1/2 in., bonding lug | $3.40 US list. The 200/400 V Dura-Glas II list gives U30-856ZP |
| II-2A | U43-22SS | Lock washer, bonding lug | Series II |
| I-3, II-3 | U17-568 | Bonding lug | Price on request. None on the P4R6H3-190 |
| I-4 | C69-2 | Water slinger | Series I, and series II in the 1999 revision |
| II-4 | 17351-0009 | Water slinger | Series II, 2003 revision. $3.01 US list |
| I-5 | C203-193P | Seal plate | Series I. Not in the 2025-2026 catalog |
| II-5 | C203-194P | Seal plate kit, with the o-ring and shaft seal what goes wrong | Series II. $267.62 US list |
| II-5 | C203-194SS | Seal plate kit, stainless | P4E6SSG36-189 and P4E6SSH36-190 |
| I-6, II-6 | U9-228AZ | O-ring, seal plate what goes wrong | $15.63 US list. The manuals print U9-228A |
| I-7 | 17304-0100S | Shaft seal what goes wrong | Series I. Not in the 2025-2026 catalog |
| II-7 | 37400-0027S | Shaft seal | Series II, 2003 revision. Not in the 2025-2026 catalog |
| II-7 | 37400-0028S | Shaft seal, Viton | Max-E-Glas II models ending LV |
| II-7 | U109-358SS | Shaft seal | Series II, 1999 revision |
| I-8, II-8 | C19-37AZ | Clamp what goes wrong | $167.19 US list. The manuals print C19-37A; three of the 2003 manual's four lists call it the knob |
| I-•, II-9 | WC36-22Z | Clamp knob | $20.34 US list. The manuals print WC36-22; three of the 2003 manual's four lists call it the clamp |
| I-• | C30-12 | Impeller screw | Series I models marked in the chart |
| I-• | C30-47 | Impeller screw | PEAXSSG-183 and PEAAXSSG-184 |
| II-10A | 17301-0151 | Impeller screw assembly | Series II |
| II-10A | 17301-0152 | Impeller screw assembly | P4R6E3-187 |
| II-10A | 37337-6080 | Impeller screw | The series II models the charts mark. $30.83 US list |
| I-11 | U30-542SSZ | Screw, #8-32 x 7/8 in., diffuser | Five. Series I, and series II with the C1-271P1 diffuser. $3.61 US list |
| II-14 | U30-922SS | Screw, diffuser | Five, with the C1-271P diffuser |
| I-12, II-13 | U43-21SSZ | Lock washer, #8 | Five. $2.91 US list |
| I-13 | U9-226 | O-ring, diffuser | Series I |
| II-12 | U9-374Z | O-ring, diffuser | Series II. $8.68 US list. The manual prints U9-374 |
| I-14 | C176-47P1 | Tank body, the pump body | Series I. Not in the 2025-2026 catalog |
| II-15 | C176-59P | Tank body, with the trap molded in | Series II. Not in the 2025-2026 catalog |
| II-16 | C3-185P | Trap cover | Series II. Not in the 2025-2026 catalog |
| II-17 | U9-375 | O-ring, trap cover what goes wrong | Series II. Not in the 2025-2026 catalog |
| II-18 | C8-58PZ | Basket what goes wrong | Series II. $22.05 US list. The manual prints C8-58P |
| I-15, II-19 | U178-920PZ | Drain plug, 1/4 in. NPT | One on the series I pump body, two on series II. $8.07 US list |
| — | U9-359Z | O-ring, drain plug | The 2025-2026 trap page. $2.89 US list |
| I-16 | C104-42P | Base with motor pad | Series I |
| I-17 | C35-11 | Motor pad | Series I |
| I-• | J104-9C | Base, steel | Series I models ending LS |
| I-• | C35-5 | Motor pad | Series I models ending LS |
| I-18 | U43-42SS | Washer, flat | Two. Series I |
| I-19 | U30-77SS | Screw, 3/8-16 x 1-3/4 in. hex head | Two. Series I, not on LS models. $8.76 US list |
| I-20, II-24 | U30-74SSZ | Screw, 3/8-16 x 1 in. hex head | Two on series I, four on LS models and series II. $7.00 US list |
| II-20 | U30-918SS | Base screw | Two. Series II. $7.88 US list |
| II-21 | U43-41SSZ | Washer, flat | Two on the series II base, four on each bolt-on trap. $4.07 US list |
| II-22 | C104-78P | Base with motor pad | Series II |
| II-22 | C104-79P | Base with motor pad | P4E6H-190L, P4E62H-190L and P4R6H3-190. $74.26 US list |
| II-23 | C35-43 | Motor pad | Series II |
| II-23 | C35-44 | Motor pad | With base C104-79P |
| I-• | C78-7P | Reducer, 2 x 1-1/2 in. | Series I |
| — | U30-856ZP | Screw, #10-32 x 1/2 in., bonding lug | 200/400 V Dura-Glas II |
| I-•, II-• | 32155-7117 | Motor nameplate | |
| I-•, II-• | 61002-0002 | Tag, caution | |
| I-• | 61002-0012 | Tag, warning | |
| I-•, II-• | C63-12 | Tag, caution and warning, bonding | |
| I-• | WC27-27 | Decal, no pipe dope | |
| II-• | U27-644 | Decal, don't overtighten | Max-E-Glas II |
| II-• | U27-635 | Decal, suitable for outdoor use | Dura-Glas II |
| I-• | U33-121 | Nameplate | Series I |
| II-• | U33-174 | Nameplate | Dura-Glas II |
| II-• | 32155-4035 | Nameplate | P4E series |
| II-• | 32155-4071 | Nameplate | P4EA series, and the P4R6E |
| T-1 | C3-139P1Z | Trap cover, 5 in. trap (Pkg. 115) what goes wrong | $92.61 US list. The manual prints C3-139P1 |
| T-2 | U9-229Z | O-ring, 5 in. trap cover | $21.54 US list. The manual prints U9-229 |
| T-3 | C108-33PZ | Strainer basket, 5 in. trap | $20.43 US list. The manual prints C108-33P |
| T-4 | C153-53P1 | Trap body, 5 in. trap | $172.68 US list |
| T-1 | 16920-0011Z | Trap lid, 6 in. trap (Pkg. 161) what goes wrong | $110.79 US list. The manual prints 16920-0011 |
| T-2 | 16920-0012 | O-ring, 6 in. trap lid | $32.52 US list |
| T-3 | 16920-0017Z | Strainer basket, 6 in. trap | $46.99 US list. The manual prints 16920-0017 |
| T-4 | C153-58P | Trap body, 6 in. trap | Not in the 2025-2026 catalog |
| T-5 | C20-123Z | Gasket, trap to pump what goes wrong | Both traps. $14.37 US list. The manual prints C20-123 |
| T-7 | U30-64SS | Cap screw, 5/16-18 x 1-1/4 in. | Four on each trap. $6.27 US list |
| T-8 | U43-11SS | Lock washer, 5/16 in. | Four on each trap. $3.59 US list |
| — | U9-285 | O-ring, adapter | 6 in. trap; the 2025-2026 trap page. $7.00 US list |
| — | PKG 115 | Trap, 5 in., complete | $230.30 US list |
| — | PKG 161 | Trap, 6 in., complete | No price in the 2025-2026 parts pages |
| — | PP1011 | Parts-Pak overhaul kit, 1/2 HP | Impeller, diffuser, shaft seal, gaskets, o-rings, hardware, shims, wear rings and inserts. Not for 2 and 3 HP PE pumps |
| — | PP1014 | Parts-Pak overhaul kit, 3/4 HP | |
| — | PP1016 | Parts-Pak overhaul kit, 1 HP | |
| — | PP1018 | Parts-Pak overhaul kit, 1-1/2 HP | |
| — | PP1000 | Parts-Pak seal and gasket kit, PE series | The shaft seal, gaskets and o-rings, for every PE horsepower |
| — | U79-11 | Trap lid wrench what goes wrong | Not in the 2025-2026 catalog |
| I-10 | C1-200PA | Diffuser | Series I |
| I-10 | C1-200PAB | Diffuser | Series I |
| I-10 | C1-216P | Diffuser | Series I |
| I-10 | C1-216PB | Diffuser | Series I |
| I-10 | C1-217P | Diffuser | Series I |
| I-10 | C1-217P1 | Diffuser | Series I |
| I-10 | C1-259P | Diffuser | Series I |
| II-11 | C1-271P | Diffuser | Dura-Glas II, Max-E-Glas II. $51.17 US list, as C1-271PZ |
| II-11 | C1-271P1 | Diffuser | Dura-Glas II, Max-E-Glas II. The catalog prints C1-271P1Z |
| II-11 | C1-271PSS | Diffuser | Max-E-Glas II |
| I-9 | C105-137PD1A | Impeller | Series I |
| I-9 | C105-137PDA | Impeller | Series I |
| I-9 | C105-137PDB1A | Impeller | Series I |
| I-9 | C105-137PDBA | Impeller | Series I |
| I-9 | C105-137PEB | Impeller | Series I |
| I-9 | C105-137PEB1 | Impeller | Series I |
| I-9 | C105-137PEBA | Impeller | Series I |
| I-9 | C105-137PKBA | Impeller | Series I |
| I-9 | C105-138PDBA | Impeller | Series I |
| I-9 | C105-138PEB | Impeller | Series I |
| I-9 | C105-138PEBA | Impeller | Series I |
| I-9 | C105-138PEBB | Impeller | Series I |
| II-10 | C105-238P | Impeller | Dura-Glas II, Max-E-Glas II |
| II-10 | C105-238PA | Impeller | Dura-Glas II |
| II-10 | C105-238PB | Impeller | Dura-Glas II, Max-E-Glas II |
| II-10 | C105-238PBA | Impeller | Dura-Glas II |
| II-10 | C105-238PDBA | Impeller | Dura-Glas II, Max-E-Glas II |
| II-10 | C105-238PDCA | Impeller | Dura-Glas II, Max-E-Glas II |
| II-10 | C105-238PEBA | Impeller | Dura-Glas II, Max-E-Glas II |
| II-10 | C105-238PLA | Impeller | Dura-Glas II, Max-E-Glas II |
| I-9 | C105-92PR | Impeller | Series I |
| I-9 | C105-92PRA | Impeller | Series I |
| I-9 | C105-92PS | Impeller | Series I |
| I-9 | C105-92PSC | Impeller | Series I |
| I-1 | 62001-1019 | Motor, 1-1/2 HP, 3-phase 575 V | Series I |
| II-1 | 62001-1021 | Motor, 3 HP, 3-phase 575 V | Max-E-Glas II |
| I-1 | 62003-2001 | Motor, 1 and 1/6 HP, 230 V | Series I |
| I-1, II-1 | 62003-2087 | Motor, 2 HP, 3-phase 575 V | Max-E-Glas II, Series I |
| I-1 | A100CHL | Motor, 1/2 HP, 115/230 V | Series I |
| I-1 | A100CLL | Motor, 1/2 HP, 115/230 V | Series I |
| I-1 | A100DHL | Motor, 3/4 HP, 115/230 V | Series I |
| I-1 | A100DLL | Motor, 3/4 HP, 115/230 V | Series I |
| I-1, II-1 | A100EHL | Motor, 1 HP, 115/230 V | Dura-Glas II, Series I |
| I-1, II-1 | A100ELL | Motor, 1 HP, 115/230 V | Dura-Glas II, Series I |
| I-1 | A100ELL-Y | Motor, 1 and 1/6 HP, 230 V | Series I |
| I-1 | A100ESLL | Motor, 1 HP, 115/230 V | Series I |
| II-1 | A100F5LL | Motor, 1-3/4 HP, 230 V | Dura-Glas II |
| II-1 | A100FHL | Motor, 1-1/2 HP, 230 V | Dura-Glas II |
| I-1, II-1 | A100FLL | Motor, 1-1/2 HP, 115/230 V | Dura-Glas II, Series I |
| I-1, II-1 | A100FLL-Y | Motor, 1-1/2 or 1-1/2 and 1/4 HP, 230 V or 230 V, two-speed | Dura-Glas II, Series I |
| I-1 | A100FSLL | Motor, 1-1/2 HP, 115/230 V | Series I |
| I-1 | A100FSLL-Y | Motor, 1-1/2 and 1/4 HP, 115 V or 230 V | Series I |
| II-1 | A100GHL | Motor, 2 HP, 230 V | Dura-Glas II |
| I-1 | A100GLL | Motor, 2 HP, 230 V | Series I |
| I-1 | AE100CH2 | Motor, 1/2 HP, 100/200 V | Series I |
| I-1 | AE100CHL | Motor, 1/2 HP, 115/230 V | Series I |
| I-1, II-1 | AE100DH2 | Motor, 3/4 HP, 100/200 V | Max-E-Glas II, Series I |
| I-1, II-1 | AE100DHL | Motor, 3/4 HP, 115/230 V | Max-E-Glas II, Series I |
| I-1 | AE100DLL | Motor, 3/4 HP, 115/230 V | Series I |
| I-1, II-1 | AE100EH2 | Motor, 1 HP, 100/200 V or 200 V | Max-E-Glas II, Series I |
| I-1, II-1 | AE100EHL | Motor, 1 HP, 115/230 V | Max-E-Glas II, Series I |
| I-1, II-1 | AE100ELL | Motor, 1 HP, 115/230 V | Max-E-Glas II, Series I |
| I-1 | AE100ELL-Y | Motor, 3/4 and 1/8 HP, 115 V | Series I |
| II-1 | AE100F5LL | Motor, 1-3/4 HP, 230 V | Max-E-Glas II |
| I-1, II-1 | AE100FH2 | Motor, 1-1/2 HP, 200 V | Max-E-Glas II, Series I |
| II-1 | AE100FHL | Motor, 1-1/2 HP, 230 V | Max-E-Glas II |
| I-1, II-1 | AE100FLL | Motor, 1-1/2 HP, 115/230 V | Max-E-Glas II, Series I |
| I-1, II-1 | AE100G5LL | Motor, 2-1/2 HP, 230 V | Dura-Glas II, Max-E-Glas II, Series I |
| II-1 | AE100GH2 | Motor, 2 HP, 200 V | Max-E-Glas II |
| II-1 | AE100GHL | Motor, 2 HP, 230 V | Dura-Glas II, Max-E-Glas II |
| II-1 | AE100GHL2 | Motor, 3 HP, 200 V | Max-E-Glas II |
| I-1, II-1 | AE100GLL | Motor, 2 HP, 230 V | Max-E-Glas II, Series I |
| I-1, II-1 | AE100GLL-Y | Motor, 2 or 2 and 1/3 HP, 230 V or 230 V, two-speed | Dura-Glas II, Series I |
| I-1, II-1 | AE100HLL | Motor, 3 HP, 230 V | Max-E-Glas II, Series I |
| I-1 | AE100SLL-Y | Motor, 1 and 1/6 HP, 115 V | Series I |
| I-1 | AP100CL | Motor, 1/2 HP, 3-phase 208-230/460 V | Series I |
| I-1, II-1 | AP100DH | Motor, 3/4 HP, 3-phase 208-230/460 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100DH2 | Motor, 3/4 HP, 3-phase 200/400 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100EH | Motor, 1 HP, 3-phase 208-230/460 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100EH2 | Motor, 1 HP, 3-phase 200/400 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100FH | Motor, 1-1/2 HP, 3-phase 208-230/460 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100FH2 | Motor, 1-1/2 HP, 3-phase 200/400 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100GH | Motor, 2 HP, 3-phase 208-230/460 V or 3-phase 230/460 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100GH2 | Motor, 2 HP, 3-phase 200/400 V | Dura-Glas II, Series I |
| I-1, II-1 | AP100HL | Motor, 3 HP, 3-phase 200-230/460 V or 3-phase 230/460 V | Dura-Glas II, Series I |