Pentair · OptiFlo
Pentair OptiFlo
The discontinued OptiFlo above-ground pump, Pentair and Sta-Rite: all 23 models, the parts still priced, and the impeller numbers its documents disagree on.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The OptiFlo is Pentair's above-ground pool pump, sold under both the Pentair and Sta-Rite names, at 3/4, 1 and 1-1/2 total horsepower. Pentair's pages for both now mark it discontinued. Its parts are still in the 2025-2026 catalog, on one page shared by both brands, with prices.
Pentair describes it as a high-flow pump with a 48-frame through-bolt motor, a large basket, a Cam and Ramp lid lock, and a discharge port you can turn. Newer models had a TEFC motor and met the Department of Energy's efficiency rules.
Which one you have
The table lists all 23 models on Pentair's two pages: 16 on the Pentair page, 7 on the Sta-Rite page, which end in SR. They differ in four ways:
- Discharge: horizontal or vertical. The Sta-Rite page lists only vertical models.
- Volts: 115 or 230. A few models are listed at 230 V, 50 Hz.
- Horsepower: 3/4, 1 or 1-1/2.
- Cord: 3 feet with a twist-lock or standard plug, 25 feet, or none. The Sta-Rite manual says UL-listed pumps came with the 3-foot cord, cUL-listed ones with no cord, and CSA-listed ones with a 25-foot cord.
The pump itself is the same: the two manuals list the same seal, volute, pot, lid, basket, seal plate and hardware.
The impeller depends on which document you read
There are three impeller numbers, and each document assigns them differently:
- The 2025-2026 catalog: 350017Z for 1 HP, at $96.64, and 350018 for 1-1/2 HP, at $102.43. No 3/4 HP impeller.
- The 2016 parts sheet: 350017 for 1 HP, 354552 for 3/4 HP and 350018 for 1-1/2 HP.
- The Sta-Rite manual: 354552 for 3/4 HP and "1 HP SPL", 350017 for 1 HP and "1-1/2 HP SPL", and 350018 for 1-1/2 HP. It doesn't say what SPL means.
- The Pentair manual: 350017 only.
So a 1 HP pump could take either of two impellers, depending on which version it is. Check the number on the old impeller before you order.
Also not in the current catalog: the seal plate, 357215, and the four square nuts, 357254. Both manuals and the 2016 sheet list them. A dealer may still have them, or know what replaced them; nothing I read says.
Replacing the seal
A drip between the motor and the pump is the mechanical seal, 354545S, at $45.83. The manual says running the pump dry can damage the seals and the housing, and that the seal can be changed without disconnecting any piping. The pump leak guide covers telling a seal leak from the others.
The manual's steps:
- Stop the pump, release the pressure, switch off the breaker and close the valves.
- Take out the four bolts, item 14, and pull the motor, seal plate and impeller away from the housing.
- Hold the motor shaft and turn the impeller counterclockwise to take it off, with the rotating half of the seal.
- Loosen the four motor through-bolts, take the seal plate off the motor, and press out the ceramic seat and its rubber gasket.
Putting it back:
- Clean the seal plate's seat, wet it with soapy water, and press the new ceramic seat in fully. Wipe the ceramic face with a clean tissue to take off fingerprints.
- Put the seal plate on the motor and tighten the through-bolts a little at a time, working across from bolt to opposite bolt, and not too hard.
- Check the shaft sits in the center of the seal. Clean the impeller hub, wet it with soapy water, wipe the new rotating seal's carbon face, and press it on.
- Screw the impeller on, then turn the shaft to make sure the impeller doesn't touch the seal plate.
- Clean the seal plate O-ring, check it's in place, and bolt the motor back to the housing, again working across from bolt to opposite bolt.
The lid, priming and the basket
The lid locks with a clamp ring. Turn it counterclockwise to its stop and lift to take it off. To put it back, line up the clamp's ears with the slots on the pot, press down and twist clockwise. The manual says to clean and look at the lid O-ring every time and calls lubricating it with silicone lubricant good practice.
To prime, fill the pot with water up to the suction opening, put the lid back and start the pump. If it hasn't primed within 5 minutes, switch it off and work through the manual's list: water in the pot, the lid tight, the O-ring sound, the pool's water level above the skimmer, clean baskets, open valves, and no air leak in the suction line. The priming guide covers the rest.
Clean the basket twice a week, the manual says.
Installing it
Put the pump below the pool's water level. The manual says more than 6 inches of suction lift means very long priming times and can damage the pump. Set it on a flat, solid base, high enough to keep the motor out of any flooding, and as close to the pool as practical. Use at least 1-1/2-inch pipe, seal threads with tape or a sealant made for plastic, never anything petroleum-based, and tighten fittings by hand plus 1-1/2 turns. Its maximum operating pressure is 25 psi, and it isn't meant to run in series with another pump.
Keep pool chemicals at least 10 feet away. The manual warns their fumes and spills can weaken the pump and filter.
On a cord-connected pump, don't use an extension cord, don't bury the cord, and replace a damaged one right away. The manual calls for a ground fault interrupter at the power supply.
Winter
Freezing damages the pump. Take out both drain plugs, the strainer pot's and the housing's, and drain the piping. If you can, bring the pump inside; if not, keep it in a weatherproof enclosure, and don't wrap the motor in plastic. Where it can't be drained, the only antifreeze the manual allows is propylene glycol: 40 percent in water protects to -50°F.
Replacing it
Hayward's 2025 cross-reference pairs the OptiFlo with its PowerFlo LX. Above-ground pool maintenance covers sizing a pump for above-ground plumbing.
Which model do you have?
The model number is on the pump label. Everything else in the range is shared — these are the parts that change with it.
| Model | HP | Listed on | Discharge | Volts | Cord |
|---|---|---|---|---|---|
| 348199 | 1 | Pentair page | Horizontal port | 115 | 3 ft, twist-lock |
| 348200 | 1 | Pentair page | Horizontal port | 115 | 3 ft, standard |
| 348201 | 1 | Pentair page | Horizontal port | 115 | 25 ft, standard |
| 348202 | 1 | Pentair page | Horizontal port | 115 | No cord |
| 340088-INT | 3/4 | Pentair page | Vertical port | 230 | No cord |
Note on 340088-INT: Pentair's page marks the voltage with an asterisk it doesn't explain. | |||||
| 340089-INT | 1 | Pentair page | Vertical port | 230 | No cord |
Note on 340089-INT: Pentair's page marks the voltage with an asterisk it doesn't explain. | |||||
| 340090-INT | 1-1/2 | Pentair page | Vertical port | 230 | No cord |
Note on 340090-INT: Pentair's page marks the voltage with an asterisk it doesn't explain. | |||||
| 340056-INT | 3/4 | Pentair page | Vertical port | 230 | No cord |
Note on 340056-INT: 50 Hz. | |||||
| 340056SR | 3/4 | Pentair page | Not given | 230 | Not given |
| 340057-INT | 1 | Pentair page | Vertical port | 230 | No cord |
Note on 340057-INT: 50 Hz. | |||||
| 340057SR | 1 | Pentair page | Not given | 230 | Not given |
| 340058-INT | 1-1/2 | Pentair page | Vertical port | 230 | No cord |
Note on 340058-INT: 50 Hz. | |||||
| 340058SR | 1-1/2 | Pentair page | Not given | 230 | Not given |
| 348195 | 1 | Pentair page | Vertical port | 115 | 3 ft, twist-lock |
| 348196 | 1 | Pentair page | Vertical port | 115 | 3 ft, standard |
| 348197 | 1 | Pentair page | Vertical port | 115 | 25 ft, standard |
| 348195SR | 1 | Sta-Rite page | Vertical port | 115 | 3 ft, twist-lock |
| 348196SR | 1 | Sta-Rite page | Vertical port | 115 | 3 ft, standard |
| 348197SR | 1 | Sta-Rite page | Vertical port | 115 | 25 ft, standard |
| 348198SR | 1 | Sta-Rite page | Vertical port | 115 | No cord |
| 340056SR-INT | 3/4 | Sta-Rite page | Vertical port | 230 | No cord |
| 340057SR-INT | 1 | Sta-Rite page | Vertical port | 230 | No cord |
| 340058SR-INT | 1-1/2 | Sta-Rite page | Vertical port | 230 | No cord |
Pentair OptiFlo parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The manual says running the pump dry can damage the seals and the pump housing, and that the seal can be changed without disconnecting the piping: take out the four bolts and pull the motor, seal plate and impeller away from the housing. Clean the seal faces with a tissue to take off fingerprints, and use soapy water, not grease, to seat both halves. $45.83 US list.
Two are needed. The manual's troubleshooting lists a damaged lid O-ring and a loose lid among the reasons a pump won't prime. It says to clean and inspect the O-ring every time the pot is opened, and calls lubricating it with silicone lubricant good practice. $8.84 US list.
To take the lid off, turn the clamp counterclockwise to its stop and lift it. To put it back, line up the clamp's ears with the slots on the pot, press the lid and clamp down, and twist clockwise. $23.14 US list.
The clear lid, at $19.13 US list. Pentair also lists a chemical-resistant lid, 357323, at $53.48.
The manual says to inspect and clean it twice a week. $34.93 US list.
The documents disagree on which impeller fits which pump, so check the one in yours before ordering. The catalog lists this one for 1 HP and 350018 for 1-1/2 HP, at $96.64 and $102.43. The Sta-Rite manual lists 350017 for 1 HP and 1-1/2 HP SPL pumps, 350018 for 1-1/2 HP, and a third, 354552, for 3/4 HP and 1 HP SPL. The Pentair manual lists only 350017.
Item 13 on the parts drawing, between the strainer pot and the volute. $8.84 US list.
Three, each with an O-ring, 192115Z at $4.04. To winterize, take out the strainer pot's plug and the housing's. $8.07 US list.
If you are doing the job anyway
The seal job uncovers the O-rings at the seal plate. Numbers carry the Z the 2025-2026 catalog prints where it lists the part.
Seal job
The seal and the two 2-357 O-rings the manual lists come to $63.51 at US list, and the seal plate O-ring has to be clean and in place when the motor goes back on.
- Mechanical seal354545S
- O-ring 2-357357255Z
Lid that won't seal
The manual's won't-prime list starts with a loose lid and a damaged lid O-ring; the lid, O-ring and clamp ring together are $51.11 at US list.
- Lid357227
- O-ring 2-357357255Z
- Clamp ring, the Cam and Ramp lid lock357239
Pentair OptiFlo manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- OptiFlo above-ground pool pump installation and user's guide, Pentair (P/N 356966 Rev. C, 2023)manual
- OptiFlo above-ground pool pump installation and user's guide, Sta-Rite, with the base-mounted Canadian units (P/N 152012 Rev. D, 2023)manual
- Pentair OptiFlo product page: the discontinued notice and the Pentair modelsspec
- Sta-Rite OptiFlo product page: the discontinued notice and the Sta-Rite modelsspec
- Pentair Pool 2025-2026 product catalog, pump parts: the OptiFlo on page 463, with US list pricesdiagram
- OptiFlo replacement parts, the older catalog page (PDF 2016)diagram
- Pentair pool and spa equipment warranty informationspec
Pentair OptiFlo warranty
One year on Pentair's row for single-speed pumps
Pentair's warranty table doesn't name the OptiFlo; its row for single-speed and booster pumps gives one year. Its warranty page covers labor on products professionally installed on above-ground pools, and not on its Above Ground Systems or on internet purchases. Pentair's OptiFlo page said it was sold only in store, through dealers and retail stores, though the manual also mentions online versions numbered EC-. The manual adds that wiring the motor to the wrong voltage voids the warranty. The pump is discontinued, so the warranty only matters on one installed from a dealer's remaining stock.
Manufacturer’s termsPentair OptiFlo complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
28 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | 357161Z | Drain plug what goes wrong | Three. $8.07 US list |
| 2 | 354545S | Mechanical seal what goes wrong | $45.83 US list |
| 3 | 350017Z | Impeller, 1 HP what goes wrong | $96.64 US list. The Sta-Rite manual: 1 HP and 1-1/2 HP SPL |
| 3 | 350018 | Impeller, 1-1/2 HP | $102.43 US list |
| 3 | 354552 | Impeller, 3/4 HP | The 2016 sheet; the Sta-Rite manual says 3/4 HP and 1 HP SPL. Not in the 2025-2026 catalog |
| 4 | 192115Z | O-ring, drain plug | Three. $4.04 US list |
| 5 | 357213 | Volute assembly | Includes the drain plugs. $44.05 US list |
| 6 | 357255Z | O-ring 2-357 what goes wrong | Two. $8.84 US list |
| 7 | 357227 | Lid what goes wrong | $19.13 US list |
| 7 | 357323 | Lid, chemical resistant | $53.48 US list |
| 8 | 357228Z | Strainer pot | Includes the drain plugs. $57.73 US list |
| 9 | 357239 | Clamp ring, Cam and Ramp what goes wrong | $23.14 US list |
| 10 | 357254 | Square nut, 1/4-20 | Four. The manuals and the 2016 sheet; not in the 2025-2026 catalog |
| 11 | 355667Z | Basket what goes wrong | $34.93 US list |
| 12 | 357215 | Seal plate | The manuals and the 2016 sheet; not in the 2025-2026 catalog |
| 13 | 350103Z | O-ring 2-130 what goes wrong | $8.84 US list |
| 14 | 98209000 | Machine screw, 1/4-20 x 1-1/2 in. | Four; they hold the motor and seal plate to the housing. $3.48 US list |
| — | 79137800 | Cord, 3 ft, standard 15 A plug | Not for use in Canada |
| — | 155234 | Cord, 3 ft, twist-lock 15 A plug | Not for use in Canada |
| — | 155371 | Cord, 25 ft, 16 gauge | Canada only: models 348197, 348197SR, 348201 and 348201SR and their EC- versions |
| — | 354621 | Enclosure housing, base-mounted Canadian units | The Sta-Rite manual |
| — | 354881 | Cap, CSA motor enclosure, with three screws | The Sta-Rite manual |
| — | 154716 | Screw, self-tapping hex head #10 | Three. The Sta-Rite manual |
| — | 155187 | Switch, toggle, double insulated | The Sta-Rite manual |
| — | 155193 | Connector, #16, switch | The Sta-Rite manual |
| — | 354658 | Insulating foam, adhesive backed | The Sta-Rite manual |
| — | 155109 | Nut, T4 prong | The Sta-Rite manual |
| — | 153263 | Base, CSA, 4 in. high | The Sta-Rite manual |