Pentair · Kreepy Krauly
Pentair Kreepy Krauly Great White
Pentair's discontinued bristle-drive suction cleaner: setting the regulator, why it climbs out or stalls, and the parts it still shares with the Dorado.
Discontinued. The manufacturer has discontinued it. Everything on this page still applies to the units already installed.

The Kreepy Krauly Great White, GW9500, is Pentair's bristle-drive suction cleaner, and Pentair's page now marks it discontinued. Like any suction cleaner, it runs off the pool pump's suction, through the skimmer or a dedicated vacuum port, and sends what it picks up to the pump basket and filter.
Pentair's current Dorado shares most of its parts. It takes the same swivel, gears, cams, oscillator kit, brushes and vacuum skirt under the same GW numbers. The shroud differs: GW9501 on the Great White, 360153 on the Dorado. Pentair's other suction cleaners in this catalog are the Rebel and the Kreepy Krauly Kruiser.
What it will and won't do
The manual says it clears a pool of debris in about four to six hours, visiting most spots within six hours in a random pattern. It spends most of its time in the deep end and visits the shallow end only a few times. In a vinyl pool with a hopper deep end, allow six to eight hours, with at least four trips to the shallow end.
It wasn't designed for steps, swimouts or use under a solar cover, or for the first cleanup of a new pool or one just opened for the season. For those, the Unidapt handle lets you put a pole on it and steer it by hand.
Setting it up
The manual's standard installation runs through the skimmer, with the vacuum regulator.
- Turn the pump off. Set the valves to send all suction to that skimmer, and close the main drain and any other suction lines.
- Take out the skimmer basket, and put in the vacuum regulator with the reducer cone.
- Fill the hose with water, with the cleaner head underwater. Air in the system can damage the pump.
- Attach the hose to the regulator, put the flow gauge in the other end underwater, and start the pump. Turn the regulator until the gauge reads between minimum and maximum.
- Take the gauge off, connect the leader hose to the cleaner, and let it sink.
With a vacuum port, the hose goes to the port, and the regulator still sits in the skimmer, with its cap on. The port's gate valve has to be fully open.
Too much suction, or not enough
Too much and it climbs the wall past the waterline, sucks air, and the pump loses prime, which the manual says damages the pump. Turn the regulator knob counterclockwise. If it still climbs, open the main drain valve slightly.
Not enough and it moves sluggishly or not at all. The oscillator should click about 500 times a minute. Clean the filter and baskets, clear the oscillator chamber and hose, fix any vacuum leaks at the hose, vac plate or reducer cone, and set the valves for maximum suction at the cleaner. If it still won't move, the manual says the pump may not be strong enough.
Looking after it
- Take it out before shocking or balancing the water, and wait at least four hours before putting it back.
- Store the hose flat and straight, off the cleaner. Coiled or left attached, it takes a set and the cleaner misbehaves.
- Store the cleaner off its bristles, with the lift brush retracted. A cleaner stored on its lift brush stops turning.
- Check the bristles and the vacuum skirt now and then, and replace them when worn.
The odd behavior that's normal
- It flips on its back when the pump stops. The manual says some systems surge back when they shut off, and the cleaner rights itself on restart.
- It rises on one side and pivots a few times a minute. That's how it turns.
Where Pentair's documents disagree
The manual dates from 2011 and the parts sheet from 2016, and several numbers changed between them. The 2025-2026 catalog follows the sheet but drops some parts.
- The bumper. GW9502 in the manual, 360227 in the 2016 sheet. The catalog lists neither, and only the manual lists the bumper insert kit.
- The screw kit, GW9504. Four short and two long in the manual, six short and two long in the sheet and catalog. The manual's own reassembly uses four screws, two long and two short.
- The hose. The manual's kit is 41200-0131, twelve sections it calls 4 ft. each, which would make 48 ft. The sheet and catalog list 41200-0130, a 40 ft. kit with leader.
- The regulator and flow gauge. 41200-0200 with cap 41200-0211, and gauge 41200-0210, in the manual. Regulator and cap 41200-0213, and gauge 41200-0212, in the sheet. The catalog prices the gauge and sells the regulator only in the accessory package.
- What's still sold. The catalog drops the lower body, the long gear shaft, the shaft kit and the ratchet tab, all in the manual and the sheet.
Which model do you have?
The model number is on the cleaner label. Everything else in the range is shared — these are the parts that change with it.
| Model | SKU | Cleaning path | Shroud |
|---|---|---|---|
| Great White | GW9500 | 15 in. | GW9501 |
Note on Great White: Pentair's only item number for it, shipped in a 15 lb carton with twelve hose sections, one of them the leader. Its page now carries the discontinued notice. | |||
Pentair Kreepy Krauly Great White parts, and what goes wrong
Read off the manufacturer’s parts list and checked before it ships. Open a row for what a bad one actually does — or start from the symptom and work down, which is the cheaper order.
What is it doing?
The cleaner rises on one side and pivots a few times a minute, which the manual says lets it change direction, get out of corners and away from ladders, and pick up leaves it's been pushing. Its test for a cleaner stuck more than 15 minutes: turn it over while it runs, still underwater, and the lift brush should drop within 2 minutes. Stored resting on the brush, the bristles collapse and it stops turning. $51.45 US list; its spring is GW9522 at $16.51.
The clicking is the oscillator moving back and forth in its chamber, and its vibration drives the bristles. Before replacing it, the manual's troubleshooting says to clean the filter and baskets, clear debris from the oscillator chamber and hose, fix vacuum leaks, and set the valves for maximum suction at the cleaner. The kit includes the seal kit, GW9004 at $20.24; the ratchet assembly isn't sold separately. $208.90 US list.
The bristles are the drive. The manual says to check the bristles and vacuum skirt now and then for wear or distortion, and to store the cleaner so nothing sits on or squashes them. The center brushes come out to change the ratchet tab. $58.31 US list; the outer brush ring kit, GW9505, is $151.18.
The rubber skirt that seals the vacuum under the cleaner. Fit it with the word OUTSIDE facing out, starting at the large pin at the back of the cleaner head, flush against the stop strips, and don't knock it out of place when the lower body goes back past the brush ring. $36.32 US list.
The manual's fix for a cleaner that won't go into the shallow end: the inserts make it more buoyant. Fit them only from the bottom; from the top they jam. If the bumper lifts the cleaner to the surface, check for trapped air in the cleaner and hose first, then take inserts out one at a time until it stays on the floor. The 2011 manual lists the kit; the later parts lists don't.
The swivel, vacuum regulator and cap, reducer cone, Unidapt handle, vac port fitting and flow gauge, and the only way the 2025-2026 catalog sells the regulator. The manual says to use the regulator at all times, as a safety device as well as a flow control, and to keep it underwater. Too much suction makes the cleaner climb out and the pump lose prime: turn the regulator knob counterclockwise, then open the main drain valve slightly if it still climbs. The reducer cone, also sold alone as GW9015 at $32.49, keeps the hose on when the pump stops. $126.28 US list.
The manual says it must be a Great White hose, not to cut the sections, and to connect the leader section, the one with the larger cuff, to the swivel. A cleaner that hovers with the hose stretched out needs more: measure from the suction connection to the farthest point of the pool and add at least 4 ft. Store it flat and straight, never coiled; a hose that has taken a set straightens after a few hours laid out in the sun. $366.27 US list.
Fits into the top of the cleaner with a quarter turn, and comes off with a quarter turn counterclockwise. The manual says the cleaner will pick up some debris big enough to jam it: stop the pump, clear it from the bottom first, then take off the swivel and clear it from the top. $41.17 US list.
If you are doing the job anyway
Pentair's disassembly has the lift brush and its spring coming off the same post.
Lift brush that no longer drops
The manual's disassembly takes the coil spring off the lift brush's mounting post, and says to replace the brush and the spring if necessary.
- Lift brushGW9517
- GW9522GW9522
Pentair Kreepy Krauly Great White manuals and documentation
Hosted by the manufacturer. These open on Pentair’s own servers, so they stay current.
- Great White automatic pool cleaner installation and user's guide (P/N 789 Rev. D, 5/12/11), English, Spanish and Frenchmanual
- Kreepy Krauly Great White product page, with the discontinued noticespec
- Pentair Pool 2025-2026 product catalog: Great White replacement parts and US list prices on page 316diagram
- Great White replacement parts, the older catalog page (PDF 2016)diagram
- Kreepy Krauly Great White brochure (P1-710, June 2015)spec
- Pentair pool product warranty informationspec
Pentair Kreepy Krauly Great White warranty
2 years parts
Two years, per Pentair's 2015 brochure. Pentair's current warranty table no longer lists the Great White, which is discontinued; its current suction cleaners, the Dorado, Kreepy Krauly and Kruiser, and Rebel, are all at two years. The manual's limited warranty excludes parts discolored by sun or chemicals, wear that doesn't affect how the cleaner works, and any damage to plaster or a vinyl liner. Its hose drawing says storing the cleaner with the hose attached voids the hose warranty.
Manufacturer’s termsPentair Kreepy Krauly Great White complete parts list
Every part on the manufacturer’s exploded diagram, in their numbering. Marked rows are the ones covered above with a symptom and a diagnosis.
36 parts
| No. | Part | Description | Note |
|---|---|---|---|
| 1 | GW9012 | Swivel assembly what goes wrong | $41.17 US list |
| 2 | 360227 | Bumper | The 2016 sheet; not in the 2025-2026 catalog |
| 2 | GW9502 | Bumper | The 2011 manual's number |
| 2A | GW9520 | Bumper insert kit, set of 4 what goes wrong | The 2011 manual |
| 3 | GW9504 | Screw kit | $19.34 US list. 6 short and 2 long in the 2016 sheet and catalog, 4 short and 2 long in the manual |
| 4 | GW9501 | Shroud | $222.26 US list |
| 5 | GW9505 | Brush ring kit, with the vacuum skirt | $151.18 US list. The manual calls it the brush ring |
| 6 | GW9506 | Oscillator chamber cap | $64.29 US list |
| 7 | GW9507 | Cam kit, 2- and 3-leg cams | $45.35 US list |
| 8 | GW9509 | Idler gear kit, 3 gears | $45.01 US list |
| 9 | GW9512 | Block kit, 2 blocks | $25.10 US list |
| 10 | GW9513 | Long gear shaft, stainless steel | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 11A | GW9536 | Shaft kit, stainless steel, with the mounting screw | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 12 | GW9535 | Lower body | The manual says it includes the chamber cap, shaft kit, lift brush, spring, ratchet tab, two idler gears and the 2-arm cam. Not in the 2025-2026 catalog |
| 13 | GW9517 | Lift brush what goes wrong | $51.45 US list |
| 14 | GW9508 | Vacuum skirt what goes wrong | $36.32 US list |
| 15 | GW9522 | Lift brush spring | $16.51 US list |
| 16 | GW9523 | Ratchet tab, stainless steel | The manual and the 2016 sheet; not in the 2025-2026 catalog |
| 17 | GW9004 | Oscillator seal kit, 2 seals | $20.24 US list |
| 18 | GW9503 | Oscillator assembly kit, with the seal kit what goes wrong | $208.90 US list |
| 19 | GW9013 | Center brush kit, set of 2 what goes wrong | $58.31 US list |
| — | GW9527 | Ratchet tab service kit | The 2016 sheet |
| — | 41200-0213 | Vacuum regulator and cap | The 2016 sheet |
| — | 41200-0200 | Vacuum regulator | The 2011 manual's number |
| — | 41200-0211 | Vacuum regulator cap | The 2011 manual's number |
| — | GW9015 | Reducer cone | $32.49 US list |
| — | GW9019 | Unidapt handle | The manual and the 2016 sheet. The manual says only this floating handle works |
| — | GW9530 | Vac port fitting | Priced on request |
| — | 41200-0212 | Flow gauge | $44.01 US list |
| — | 41200-0210 | Flow gauge | The 2011 manual's number |
| — | 41200-0130 | Hose sectional kit with leader, 40 ft. what goes wrong | $366.27 US list |
| — | 41200-0131 | Hose kit, 12 sections, 4 ft. each | The 2011 manual's number |
| — | 41200-0133 | Hose, bulk pack of 20 sections, 1-1/2 in. | $501.29 US list |
| — | 41200-0134 | Hose, bulk pack of 12 leader sections | $338.26 US list |
| — | 77705-0200 | Accessory package what goes wrong | The swivel, regulator and cap, reducer cone, handle, vac port fitting and flow gauge. $126.28 US list |
| — | R211084K | In-line leaf canister | The manual's suggestion for pools with lots of leaves |